bool
default y
select RTC_LIB
+ select SYS_SUPPORTS_APM_EMULATION
help
The ARM series is a line of low-power-consumption RISC chip designs
licensed by ARM Ltd and targeted at embedded applications and
Europe. There is an ARM Linux project with a web page at
<http://www.arm.linux.org.uk/>.
+config SYS_SUPPORTS_APM_EMULATION
+ bool
+
+config GENERIC_GPIO
+ bool
+ default n
+
config GENERIC_TIME
bool
default n
bool
default y
+config NO_IOPORT
+ bool
+ default n
+
config EISA
bool
---help---
config ARCH_MAY_HAVE_PC_FDC
bool
+config ZONE_DMA
+ bool
+ default y
+
config GENERIC_ISA_DMA
bool
config ARCH_AT91
bool "Atmel AT91"
+ select GENERIC_GPIO
help
This enables support for systems based on the Atmel AT91RM9200
and AT91SAM9xxx processors.
bool "Cirrus CL-PS7500FE"
select TIMER_ACORN
select ISA
+ select NO_IOPORT
help
Support for the Cirrus Logic PS7500FE system-on-a-chip.
config ARCH_EBSA110
bool "EBSA-110"
select ISA
+ select NO_IOPORT
help
This is an evaluation board for the StrongARM processor available
from Digital. It has limited hardware on-board, including an
config ARCH_IOP13XX
bool "IOP13xx-based"
+ depends on MMU
+ select PLAT_IOP
select PCI
help
Support for Intel's IOP13XX (XScale) family of processors.
If you have any questions or comments about the Linux kernel port
to this board, send e-mail to <sjhill@cotw.com>.
+config ARCH_NS9XXX
+ bool "NetSilicon NS9xxx"
+ help
+ Say Y here if you intend to run this kernel on a NetSilicon NS9xxx
+ System.
+
+ <http://www.digi.com/products/microprocessors/index.jsp>
+
config ARCH_PNX4008
bool "Philips Nexperia PNX4008 Mobile"
help
bool "PXA2xx-based"
depends on MMU
select ARCH_MTD_XIP
+ select GENERIC_GPIO
+ select GENERIC_TIME
help
Support for Intel's PXA2XX processor line.
select TIMER_ACORN
select ARCH_MAY_HAVE_PC_FDC
select ISA_DMA_API
+ select NO_IOPORT
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
select ISA
select ARCH_DISCONTIGMEM_ENABLE
select ARCH_MTD_XIP
+ select GENERIC_GPIO
help
Support for StrongARM 11x0 based boards.
config ARCH_S3C2410
- bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442"
+ bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
+ select GENERIC_GPIO
help
Samsung S3C2410X CPU based systems, such as the Simtec Electronics
BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
config ARCH_OMAP
bool "TI OMAP"
+ select GENERIC_GPIO
+ select GENERIC_TIME
help
Support for TI's OMAP platform (OMAP1 and OMAP2).
source "arch/arm/mach-s3c2412/Kconfig"
source "arch/arm/mach-s3c2440/Kconfig"
source "arch/arm/mach-s3c2442/Kconfig"
+source "arch/arm/mach-s3c2443/Kconfig"
endif
source "arch/arm/mach-lh7a40x/Kconfig"
source "arch/arm/mach-realview/Kconfig"
-source "arch/arm/mach-at91rm9200/Kconfig"
+source "arch/arm/mach-at91/Kconfig"
source "arch/arm/mach-netx/Kconfig"
+source "arch/arm/mach-ns9xxx/Kconfig"
+
# Definitions to make life easier
config ARCH_ACORN
bool
config IWMMXT
bool "Enable iWMMXt support"
- depends CPU_XSCALE || CPU_XSC3
+ depends on CPU_XSCALE || CPU_XSC3
default y if PXA27x
help
Enable support for iWMMXt context switching at run time if
config LEDS_TIMER
bool "Timer LED" if (!ARCH_CDB89712 && !ARCH_OMAP) || \
- MACH_OMAP_H2 || MACH_OMAP_PERSEUS2
+ OMAP_OSK_MISTRAL || MACH_OMAP_H2 \
+ || MACH_OMAP_PERSEUS2
depends on LEDS
default y if ARCH_EBSA110
help
config LEDS_CPU
bool "CPU usage LED" if (!ARCH_CDB89712 && !ARCH_EBSA110 && \
- !ARCH_OMAP) || MACH_OMAP_H2 || MACH_OMAP_PERSEUS2
+ !ARCH_OMAP) \
+ || OMAP_OSK_MISTRAL || MACH_OMAP_H2 \
+ || MACH_OMAP_PERSEUS2
depends on LEDS
help
If you say Y here, the red LED will be used to give a good real
be linked for and stored to. This address is dependent on your
own flash usage.
+config KEXEC
+ bool "Kexec system call (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ kexec is a system call that implements the ability to shutdown your
+ current kernel, and to start another kernel. It is like a reboot
+ but it is indepedent of the system firmware. And like a reboot
+ you can start any kernel with it, not just Linux.
+
+ It is an ongoing process to be certain the hardware in a machine
+ is properly shutdown, so do not be surprised if this code does not
+ initially work for you. It may help to enable device hotplugging
+ support.
+
endmenu
if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_IMX )
source "kernel/power/Kconfig"
-config APM
- tristate "Advanced Power Management Emulation"
- ---help---
- APM is a BIOS specification for saving power using several different
- techniques. This is mostly useful for battery powered laptops with
- APM compliant BIOSes. If you say Y here, the system time will be
- reset after a RESUME operation, the /proc/apm device will provide
- battery status information, and user-space programs will receive
- notification of APM "events" (e.g. battery status change).
-
- In order to use APM, you will need supporting software. For location
- and more information, read <file:Documentation/pm.txt> and the
- Battery Powered Linux mini-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- This driver does not spin down disk drives (see the hdparm(8)
- manpage ("man 8 hdparm") for that), and it doesn't turn off
- VESA-compliant "green" monitors.
-
- Generally, if you don't have a battery in your machine, there isn't
- much point in using this driver and you should say N. If you get
- random kernel OOPSes or reboots that don't seem to be related to
- anything, try disabling/enabling this option (or disabling/enabling
- APM in your BIOS).
-
endmenu
source "net/Kconfig"
source "drivers/rtc/Kconfig"
+if ARCH_OMAP
+source "drivers/cbus/Kconfig"
+endif
+
endmenu
source "fs/Kconfig"
projects / linux-2.6-omap-h63xx.git / blobdiff