SUSPEND System suspend states are enabled.
FTRACE Function tracing enabled.
TS Appropriate touchscreen support is enabled.
+ UMS USB Mass Storage support is enabled.
USB USB support is enabled.
USBHID USB Human Interface Device support is enabled.
V4L Video For Linux support is enabled.
clearcpuid=BITNUM [X86]
Disable CPUID feature X for the kernel. See
- include/asm-x86/cpufeature.h for the valid bit numbers.
- Note the Linux specific bits are not necessarily
+ arch/x86/include/asm/cpufeature.h for the valid bit
+ numbers. Note the Linux specific bits are not necessarily
stable over kernel options, but the vendor specific
ones should be.
Also note that user programs calling CPUID directly
not work reliably with all consoles, but is known
to work with serial and VGA consoles.
+ coredump_filter=
+ [KNL] Change the default value for
+ /proc/<pid>/coredump_filter.
+ See also Documentation/filesystems/proc.txt.
+
cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
Format:
<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
hlt [BUGS=ARM,SH]
+ hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
+ terminal devices. Valid values: 0..8
+
i8042.debug [HW] Toggle i8042 debug mode
i8042.direct [HW] Put keyboard port into non-translated mode
i8042.dumbkbd [HW] Pretend that controller can only read data from
inttest= [IA64]
+ iomem= Disable strict checking of access to MMIO memory
+ strict regions from userspace.
+ relaxed
+
iommu= [x86]
off
force
If there are multiple matching configurations changing
the same attribute, the last one is used.
+ lmb=debug [KNL] Enable lmb debug messages.
+
load_ramdisk= [RAM] List of ramdisks to load from floppy
See Documentation/blockdev/ramdisk.txt.
nosoftlockup [KNL] Disable the soft-lockup detector.
+ noswapaccount [KNL] Disable accounting of swap in memory resource
+ controller. (See Documentation/controllers/memory.txt)
+
nosync [HW,M68K] Disables sync negotiation for all devices.
notsc [BUGS=X86-32] Disable Time Stamp Counter
nr_uarts= [SERIAL] maximum number of UARTs to be registered.
+ ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
+ See Documentation/debugging-via-ohci1394.txt for more
+ info.
+
olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
Rather than timing out after 20 ms if an EC
command is not properly ACKed, override the length
autoconfiguration.
Ranges are in pairs (memory base and size).
- dynamic_printk
- Enables pr_debug()/dev_dbg() calls if
- CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
- be switched on/off via <debugfs>/dynamic_printk/modules
+ dynamic_printk Enables pr_debug()/dev_dbg() calls if
+ CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
+ These can also be switched on/off via
+ <debugfs>/dynamic_printk/modules
print-fatal-signals=
[KNL] debug: print fatal signals
reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
Format: <reboot_mode>[,<reboot_mode2>[,...]]
- See arch/*/kernel/reboot.c or arch/*/kernel/process.c
+ See arch/*/kernel/reboot.c or arch/*/kernel/process.c
relax_domain_level=
[KNL, SMP] Set scheduler's default relax_domain_level.
See comment before function dc390_setup() in
drivers/scsi/tmscsim.c.
+ topology= [S390]
+ Format: {off | on}
+ Specify if the kernel should make use of the cpu
+ topology informations if the hardware supports these.
+ The scheduler will make use of these informations and
+ e.g. base its process migration decisions on it.
+ Default is off.
+
tp720= [HW,PS2]
trix= [HW,OSS] MediaTrix AudioTrix Pro
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
+ usb-storage.delay_use=
+ [UMS] The delay in seconds before a new device is
+ scanned for Logical Units (default 5).
+
+ usb-storage.quirks=
+ [UMS] A list of quirks entries to supplement or
+ override the built-in unusual_devs list. List
+ entries are separated by commas. Each entry has
+ the form VID:PID:Flags where VID and PID are Vendor
+ and Product ID values (4-digit hex numbers) and
+ Flags is a set of characters, each corresponding
+ to a common usb-storage quirk flag as follows:
+ a = SANE_SENSE (collect more than 18 bytes
+ of sense data);
+ c = FIX_CAPACITY (decrease the reported
+ device capacity by one sector);
+ h = CAPACITY_HEURISTICS (decrease the
+ reported device capacity by one
+ sector if the number is odd);
+ i = IGNORE_DEVICE (don't bind to this
+ device);
+ l = NOT_LOCKABLE (don't try to lock and
+ unlock ejectable media);
+ m = MAX_SECTORS_64 (don't transfer more
+ than 64 sectors = 32 KB at a time);
+ o = CAPACITY_OK (accept the capacity
+ reported by the device);
+ r = IGNORE_RESIDUE (the device reports
+ bogus residue values);
+ s = SINGLE_LUN (the device has only one
+ Logical Unit);
+ w = NO_WP_DETECT (don't test whether the
+ medium is write-protected).
+ Example: quirks=0419:aaf5:rl,0421:0433:rc
+
add_efi_memmap [EFI; x86-32,X86-64] Include EFI memory map in
kernel's map of available physical RAM.
Format:
<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
- norandmaps Don't use address space randomization
- Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space
+ norandmaps Don't use address space randomization. Equivalent to
+ echo 0 > /proc/sys/kernel/randomize_va_space
______________________________________________________________________
projects / linux-2.6-omap-h63xx.git / blobdiff