[SCSI] 3w-xxxx: remove unnecessary local_irq_save/restore for scsi sg copy API

[linux-2.6-omap-h63xx.git] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 329dcabe4c5eae0382a2902839d0f91d69d442d7..dd28a0d56981e4e0376fb5010086c817633a6a3b 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -284,6 +284,11 @@ and is between 256 and 4096 characters. It is defined in the file
                        isolate - enable device isolation (each device, as far
                                  as possible, will get its own protection
                                  domain)
+                       fullflush - enable flushing of IO/TLB entries when
+                                   they are unmapped. Otherwise they are
+                                   flushed before they will be reused, which
+                                   is a lot of faster
+
        amd_iommu_size= [HW,X86-64]
                        Define the size of the aperture for the AMD IOMMU
                        driver. Possible values are:
@@ -653,11 +658,12 @@ and is between 256 and 4096 characters. It is defined in the file
        earlyprintk=    [X86-32,X86-64,SH,BLACKFIN]
                        earlyprintk=vga
                        earlyprintk=serial[,ttySn[,baudrate]]
+                       earlyprintk=dbgp
 
                        Append ",keep" to not disable it when the real console
                        takes over.
 
-                       Only vga or serial at a time, not both.
+                       Only vga or serial or usb debug port at a time.
 
                        Currently only ttyS0 and ttyS1 are supported.
 
@@ -790,6 +796,7 @@ and is between 256 and 4096 characters. It is defined in the file
                        Defaults to the default architecture's huge page size
                        if not specified.
 
+       i8042.debug     [HW] Toggle i8042 debug mode
        i8042.direct    [HW] Put keyboard port into non-translated mode
        i8042.dumbkbd   [HW] Pretend that controller can only read data from
                             keyboard and cannot control its state
@@ -1014,6 +1021,10 @@ and is between 256 and 4096 characters. It is defined in the file
                        (only serial suported for now)
                        Format: <serial_device>[,baud]
 
+       kmac=           [MIPS] korina ethernet MAC address.
+                       Configure the RouterBoard 532 series on-chip
+                       Ethernet adapter MAC address.
+
        l2cr=           [PPC]
 
        l3cr=           [PPC]
@@ -1222,6 +1233,29 @@ and is between 256 and 4096 characters. It is defined in the file
                                 or
                                 memmap=0x10000$0x18690000
 
+       memory_corruption_check=0/1 [X86]
+                       Some BIOSes seem to corrupt the first 64k of
+                       memory when doing things like suspend/resume.
+                       Setting this option will scan the memory
+                       looking for corruption.  Enabling this will
+                       both detect corruption and prevent the kernel
+                       from using the memory being corrupted.
+                       However, its intended as a diagnostic tool; if
+                       repeatable BIOS-originated corruption always
+                       affects the same memory, you can use memmap=
+                       to prevent the kernel from using that memory.
+
+       memory_corruption_check_size=size [X86]
+                       By default it checks for corruption in the low
+                       64k, making this memory unavailable for normal
+                       use.  Use this parameter to scan for
+                       corruption in more or less memory.
+
+       memory_corruption_check_period=seconds [X86]
+                       By default it checks for corruption every 60
+                       seconds.  Use this parameter to check at some
+                       other rate.  0 disables periodic checking.
+
        memtest=        [KNL,X86] Enable memtest
                        Format: <integer>
                        range: 0,4 : pattern number
@@ -1419,6 +1453,12 @@ and is between 256 and 4096 characters. It is defined in the file
 
        nolapic_timer   [X86-32,APIC] Do not use the local APIC timer.
 
+       nox2apic        [X86-64,APIC] Do not enable x2APIC mode.
+
+       x2apic_phys     [X86-64,APIC] Use x2apic physical mode instead of
+                       default x2apic cluster mode on platforms
+                       supporting x2apic.
+
        noltlbs         [PPC] Do not use large page/tlb entries for kernel
                        lowmem mapping on PPC40x.
 
@@ -1674,6 +1714,11 @@ and is between 256 and 4096 characters. It is defined in the file
                        autoconfiguration.
                        Ranges are in pairs (memory base and size).
 
+       dynamic_printk
+                       Enables pr_debug()/dev_dbg() calls if
+                       CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
+                       be switched on/off via <debugfs>/dynamic_printk/modules
+
        print-fatal-signals=
                        [KNL] debug: print fatal signals
                        print-fatal-signals=1: print segfault info to