ISAPNP ISA PnP code is enabled.
ISDN Appropriate ISDN support is enabled.
JOY Appropriate joystick support is enabled.
+ KMEMTRACE kmemtrace is enabled.
LIBATA Libata driver is enabled
LP Printer support is enabled.
LOOP Loopback device support is enabled.
SPARC Sparc architecture is enabled.
SWSUSP Software suspend (hibernation) is enabled.
SUSPEND System suspend states are enabled.
+ FTRACE Function tracing enabled.
TS Appropriate touchscreen support is enabled.
USB USB support is enabled.
USBHID USB Human Interface Device support is enabled.
parameter will force ia64_sal_cache_flush to call
ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
+ ftrace=[tracer]
+ [ftrace] will set and start the specified tracer
+ as early as possible in order to facilitate early
+ boot debugging.
+
+ ftrace_dump_on_oops
+ [ftrace] will dump the trace buffers on oops.
+
gamecon.map[2|3]=
[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
support via parallel port (up to 5 devices per port)
hlt [BUGS=ARM,SH]
+ hvc_iucv= [S390] Number of z/VM IUCV Hypervisor console (HVC)
+ back-ends. Valid parameters: 0..8
+
i8042.debug [HW] Toggle i8042 debug mode
i8042.direct [HW] Put keyboard port into non-translated mode
i8042.dumbkbd [HW] Pretend that controller can only read data from
use the HighMem zone if it exists, and the Normal
zone if it does not.
+ kmemtrace.enable= [KNL,KMEMTRACE] Format: { yes | no }
+ Controls whether kmemtrace is enabled
+ at boot-time.
+
+ kmemtrace.subbufs=n [KNL,KMEMTRACE] Overrides the number of
+ subbufs kmemtrace's relay channel has. Set this
+ higher than default (KMEMTRACE_N_SUBBUFS in code) if
+ you experience buffer overruns.
+
movablecore=nn[KMG] [KNL,X86-32,IA-64,PPC,X86-64] This parameter
is similar to kernelcore except it specifies the
amount of memory used for migratable allocations.
when a NMI is triggered.
Format: [state][,regs][,debounce][,die]
- nmi_watchdog= [KNL,BUGS=X86-32] Debugging features for SMP kernels
+ nmi_watchdog= [KNL,BUGS=X86-32,X86-64] Debugging features for SMP kernels
+ Format: [panic,][num]
+ Valid num: 0,1,2
+ 0 - turn nmi_watchdog off
+ 1 - use the IO-APIC timer for the NMI watchdog
+ 2 - use the local APIC for the NMI watchdog using
+ a performance counter. Note: This will use one performance
+ counter and the local APIC's performance vector.
+ When panic is specified panic when an NMI watchdog timeout occurs.
+ This is useful when you use a panic=... timeout and need the box
+ quickly up again.
+ Instead of 1 and 2 it is possible to use the following
+ symbolic names: lapic and ioapic
+ Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic
no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
emulation library even if a 387 maths coprocessor
instruction doesn't work correctly and not to
use it.
+ no_file_caps Tells the kernel not to honor file capabilities. The
+ only way then for a file to be executed with privilege
+ is to be setuid root or executed by root.
+
nohalt [IA-64] Tells the kernel not to use the power saving
function PAL_HALT_LIGHT when idle. This increases
power-consumption. On the positive side, it reduces
nomsi [MSI] If the PCI_MSI kernel config parameter is
enabled, this kernel boot option can be used to
disable the use of MSI interrupts system-wide.
+ noioapicquirk [APIC] Disable all boot interrupt quirks.
+ Safety option to keep boot IRQs enabled. This
+ should never be necessary.
+ ioapicreroute [APIC] Enable rerouting of boot IRQs to the
+ primary IO-APIC for bridges that cannot disable
+ boot IRQs. This fixes a source of spurious IRQs
+ when the system masks IRQs.
+ noioapicreroute [APIC] Disable workaround that uses the
+ boot IRQ equivalent of an IRQ that connects to
+ a chipset where boot IRQs cannot be disabled.
+ The opposite of ioapicreroute.
biosirq [X86-32] Use PCI BIOS calls to get the interrupt
routing table. These calls are known to be buggy
on several machines and they hang the machine
st= [HW,SCSI] SCSI tape parameters (buffers, etc.)
See Documentation/scsi/st.txt.
+ stacktrace [FTRACE]
+ Enabled the stack tracer on boot up.
+
sti= [PARISC,HW]
Format: <num>
Set the STI (builtin display/keyboard on the HP-PARISC
See comment before function dc390_setup() in
drivers/scsi/tmscsim.c.
+ topology= [S390]
+ Format: {off | on}
+ Specify if the kernel should make use of the cpu
+ topology informations if the hardware supports these.
+ The scheduler will make use of these informations and
+ e.g. base its process migration decisions on it.
+ Default is off.
+
tp720= [HW,PS2]
trix= [HW,OSS] MediaTrix AudioTrix Pro
Format:
<io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
+ tsc= Disable clocksource-must-verify flag for TSC.
+ Format: <string>
+ [x86] reliable: mark tsc clocksource as reliable, this
+ disables clocksource verification at runtime.
+ Used to enable high-resolution timer mode on older
+ hardware, and in virtualized environment.
+
turbografx.map[2|3]= [HW,JOY]
TurboGraFX parallel port interface
Format: