SH SuperH architecture is enabled.
SMP The kernel is an SMP kernel.
SPARC Sparc architecture is enabled.
- SWSUSP Software suspend is enabled.
+ SWSUSP Software suspend (hibernation) is enabled.
+ SUSPEND System suspend states are enabled.
TS Appropriate touchscreen support is enabled.
USB USB support is enabled.
USBHID USB Human Interface Device support is enabled.
default: 0
acpi_sleep= [HW,ACPI] Sleep options
- Format: { s3_bios, s3_mode, s3_beep, old_ordering }
+ Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, old_ordering }
See Documentation/power/video.txt for s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
as soon as the kernel's real-mode entry point is called.
+ s4_nohwsig prevents ACPI hardware signature from being
+ used during resume from hibernation.
old_ordering causes the ACPI 1.0 ordering of the _PTS
control method, wrt putting devices into low power
states, to be enforced (the ACPI 2.0 ordering of _PTS is
no delay (0).
Format: integer
+ bootmem_debug [KNL] Enable bootmem allocator debug messages.
+
bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
bttv.radio= Most important insmod options are available as
kernel args too.
hisax= [HW,ISDN]
See Documentation/isdn/README.HiSax.
- hugepages= [HW,X86-32,IA-64] Maximal number of HugeTLB pages.
- hugepagesz= [HW,IA-64,PPC] The size of the HugeTLB pages.
+ hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
+ hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
+ On x86-64 and powerpc, this option can be specified
+ multiple times interleaved with hugepages= to reserve
+ huge pages of different sizes. Valid pages sizes on
+ x86-64 are 2M (when the CPU supports "pse") and 1G
+ (when the CPU supports the "pdpe1gb" cpuinfo flag)
+ Note that 1GB pages can only be allocated at boot time
+ using hugepages= and not freed afterwards.
+ default_hugepagesz=
+ [same as hugepagesz=] The size of the default
+ HugeTLB page size. This is the size represented by
+ the legacy /proc/ hugepages APIs, used for SHM, and
+ default size when mounting hugetlbfs filesystems.
+ Defaults to the default architecture's huge page size
+ if not specified.
i8042.direct [HW] Put keyboard port into non-translated mode
i8042.dumbkbd [HW] Pretend that controller can only read data from
* [no]ncq: Turn on or off NCQ.
+ * nohrst, nosrst, norst: suppress hard, soft
+ and both resets.
+
If there are multiple matching configurations changing
the same attribute, the last one is used.
or
memmap=0x10000$0x18690000
+ memory_corruption_check=0/1 [X86]
+ Some BIOSes seem to corrupt the first 64k of
+ memory when doing things like suspend/resume.
+ Setting this option will scan the memory
+ looking for corruption. Enabling this will
+ both detect corruption and prevent the kernel
+ from using the memory being corrupted.
+ However, its intended as a diagnostic tool; if
+ repeatable BIOS-originated corruption always
+ affects the same memory, you can use memmap=
+ to prevent the kernel from using that memory.
+
+ memory_corruption_check_size=size [X86]
+ By default it checks for corruption in the low
+ 64k, making this memory unavailable for normal
+ use. Use this parameter to scan for
+ corruption in more or less memory.
+
+ memory_corruption_check_period=seconds [X86]
+ By default it checks for corruption every 60
+ seconds. Use this parameter to check at some
+ other rate. 0 disables periodic checking.
+
memtest= [KNL,X86] Enable memtest
Format: <integer>
range: 0,4 : pattern number
mga= [HW,DRM]
+ mminit_loglevel=
+ [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
+ parameter allows control of the logging verbosity for
+ the additional memory initialisation checks. A value
+ of 0 disables mminit logging and a level of 4 will
+ log everything. Information is printed at KERN_DEBUG
+ so loglevel=8 may also need to be specified.
+
mousedev.tap_time=
[MOUSE] Maximum time between finger touching and
leaving touchpad surface for touch to be considered
tdfx= [HW,DRM]
+ test_suspend= [SUSPEND]
+ Specify "mem" (for Suspend-to-RAM) or "standby" (for
+ standby suspend) as the system sleep state to briefly
+ enter during system startup. The system is woken from
+ this state using a wakeup-capable RTC alarm.
+
thash_entries= [KNL,NET]
Set number of hash buckets for TCP connection
<deci-seconds>: poll all this frequency
0: no polling (default)
- tipar.timeout= [HW,PPT]
- Set communications timeout in tenths of a second
- (default 15).
-
- tipar.delay= [HW,PPT]
- Set inter-bit delay in microseconds (default 10).
-
tmscsim= [HW,SCSI]
See comment before function dc390_setup() in
drivers/scsi/tmscsim.c.