2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_ADS7846
15 tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
17 depends on HWMON = n || HWMON
19 Say Y here if you have a touchscreen interface using the
20 ADS7846/TSC2046 or ADS7843 controller, and your board-specific
21 setup code includes that in its table of SPI devices.
23 If HWMON is selected, and the driver is told the reference voltage
24 on your board, you will also get hwmon interfaces for the voltage
25 (and on ads7846/tsc2046, temperature) sensors of this chip.
27 If unsure, say N (but it's safe to say "Y").
29 To compile this driver as a module, choose M here: the
30 module will be called ads7846.
32 config TOUCHSCREEN_BITSY
33 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
34 depends on SA1100_BITSY
37 Say Y here if you have the h3600 (Bitsy) touchscreen.
41 To compile this driver as a module, choose M here: the
42 module will be called h3600_ts_input.
44 config TOUCHSCREEN_CORGI
45 tristate "SharpSL (Corgi and Spitz series) touchscreen driver (DEPRECATED)"
46 depends on PXA_SHARPSL
47 select CORGI_SSP_DEPRECATED
50 Say Y here to enable the driver for the touchscreen on the
51 Sharp SL-C7xx and SL-Cxx00 series of PDAs.
55 To compile this driver as a module, choose M here: the
56 module will be called corgi_ts.
58 NOTE: this driver is deprecated, try enable SPI and generic
59 ADS7846-based touchscreen driver.
61 config TOUCHSCREEN_FUJITSU
62 tristate "Fujitsu serial touchscreen"
65 Say Y here if you have the Fujitsu touchscreen (such as one
66 installed in Lifebook P series laptop) connected to your
71 To compile this driver as a module, choose M here: the
72 module will be called fujitsu-ts.
74 config TOUCHSCREEN_GUNZE
75 tristate "Gunze AHL-51S touchscreen"
78 Say Y here if you have the Gunze AHL-51 touchscreen connected to
83 To compile this driver as a module, choose M here: the
84 module will be called gunze.
86 config TOUCHSCREEN_ELO
87 tristate "Elo serial touchscreens"
90 Say Y here if you have an Elo serial touchscreen connected to
95 To compile this driver as a module, choose M here: the
96 module will be called elo.
98 config TOUCHSCREEN_MTOUCH
99 tristate "MicroTouch serial touchscreens"
102 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
107 To compile this driver as a module, choose M here: the
108 module will be called mtouch.
110 config TOUCHSCREEN_INEXIO
111 tristate "iNexio serial touchscreens"
114 Say Y here if you have an iNexio serial touchscreen connected to
119 To compile this driver as a module, choose M here: the
120 module will be called inexio.
122 config TOUCHSCREEN_MK712
123 tristate "ICS MicroClock MK712 touchscreen"
125 Say Y here if you have the ICS MicroClock MK712 touchscreen
126 controller chip in your system.
130 To compile this driver as a module, choose M here: the
131 module will be called mk712.
133 config TOUCHSCREEN_HP600
134 tristate "HP Jornada 6xx touchscreen"
135 depends on SH_HP6XX && SH_ADC
137 Say Y here if you have a HP Jornada 620/660/680/690 and want to
138 support the built-in touchscreen.
140 To compile this driver as a module, choose M here: the
141 module will be called hp680_ts_input.
143 config TOUCHSCREEN_HP7XX
144 tristate "HP Jornada 7xx touchscreen"
145 depends on SA1100_JORNADA720_SSP
147 Say Y here if you have a HP Jornada 710/720/728 and want
148 to support the built-in touchscreen.
150 To compile this driver as a module, choose M here: the
151 module will be called jornada720_ts.
153 config TOUCHSCREEN_HTCPEN
154 tristate "HTC Shift X9500 touchscreen"
157 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
158 Clio / Shangrila and want to support the built-in touchscreen.
162 To compile this driver as a module, choose M here: the
163 module will be called htcpen.
165 config TOUCHSCREEN_PENMOUNT
166 tristate "Penmount serial touchscreen"
169 Say Y here if you have a Penmount serial touchscreen connected to
174 To compile this driver as a module, choose M here: the
175 module will be called penmount.
177 config TOUCHSCREEN_MIGOR
178 tristate "Renesas MIGO-R touchscreen"
179 depends on SH_MIGOR && I2C
181 Say Y here to enable MIGO-R touchscreen support.
185 To compile this driver as a module, choose M here: the
186 module will be called migor_ts.
188 config TOUCHSCREEN_TOUCHRIGHT
189 tristate "Touchright serial touchscreen"
192 Say Y here if you have a Touchright serial touchscreen connected to
197 To compile this driver as a module, choose M here: the
198 module will be called touchright.
200 config TOUCHSCREEN_TOUCHWIN
201 tristate "Touchwin serial touchscreen"
204 Say Y here if you have a Touchwin serial touchscreen connected to
209 To compile this driver as a module, choose M here: the
210 module will be called touchwin.
212 config TOUCHSCREEN_ATMEL_TSADCC
213 tristate "Atmel Touchscreen Interface"
214 depends on ARCH_AT91SAM9RL
216 Say Y here if you have a 4-wire touchscreen connected to the
217 ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
221 To compile this driver as a module, choose M here: the
222 module will be called atmel_tsadcc.
224 config TOUCHSCREEN_TSC2005
225 tristate "TSC2005 touchscreen support"
226 depends on SPI_MASTER
228 Say Y here for if you are using the touchscreen features of TSC2005.
230 config TOUCHSCREEN_TSC210X
231 tristate "TI TSC210x based touchscreens"
232 depends on SPI_MASTER
235 Say Y here if you have a touchscreen interface using a
236 TI TSC210x controller, and your board-specific initialisation
237 code includes that in its table of SPI devices.
239 If unsure, say N (but it's safe to say "Y").
241 To compile this driver as a module, choose M here: the
242 module will be called tsc210x_ts.
244 config TOUCHSCREEN_TSC2301
245 tristate "TSC2301 touchscreen support"
246 depends on SPI_TSC2301
248 Say Y here for if you are using the touchscreen features of TSC2301.
250 config TOUCHSCREEN_UCB1400
251 tristate "Philips UCB1400 touchscreen"
253 depends on UCB1400_CORE
255 This enables support for the Philips UCB1400 touchscreen interface.
256 The UCB1400 is an AC97 audio codec. The touchscreen interface
257 will be initialized only after the ALSA subsystem has been
258 brought up and the UCB1400 detected. You therefore have to
259 configure ALSA support as well (either built-in or modular,
260 independently of whether this driver is itself built-in or
261 modular) for this driver to work.
263 To compile this driver as a module, choose M here: the
264 module will be called ucb1400_ts.
266 config TOUCHSCREEN_WM97XX
267 tristate "Support for WM97xx AC97 touchscreen controllers"
270 Say Y here if you have a Wolfson Microelectronics WM97xx
271 touchscreen connected to your system. Note that this option
272 only enables core driver, you will also need to select
273 support for appropriate chip below.
277 To compile this driver as a module, choose M here: the
278 module will be called wm97xx-ts.
280 config TOUCHSCREEN_WM9705
281 bool "WM9705 Touchscreen interface support"
282 depends on TOUCHSCREEN_WM97XX
285 Say Y here to enable support for the Wolfson Microelectronics
286 WM9705 touchscreen controller.
288 config TOUCHSCREEN_WM9712
289 bool "WM9712 Touchscreen interface support"
290 depends on TOUCHSCREEN_WM97XX
293 Say Y here to enable support for the Wolfson Microelectronics
294 WM9712 touchscreen controller.
296 config TOUCHSCREEN_WM9713
297 bool "WM9713 Touchscreen interface support"
298 depends on TOUCHSCREEN_WM97XX
301 Say Y here to enable support for the Wolfson Microelectronics
302 WM9713 touchscreen controller.
304 config TOUCHSCREEN_WM97XX_MAINSTONE
305 tristate "WM97xx Mainstone accelerated touch"
306 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
308 Say Y here for support for streaming mode with WM97xx touchscreens
309 on Mainstone systems.
313 To compile this driver as a module, choose M here: the
314 module will be called mainstone-wm97xx.
316 config TOUCHSCREEN_USB_COMPOSITE
317 tristate "USB Touchscreen Driver"
318 depends on USB_ARCH_HAS_HCD
321 USB Touchscreen driver for:
322 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
323 - PanJit TouchSet USB
324 - 3M MicroTouch USB (EX II series)
326 - some other eTurboTouch
329 - IRTOUCHSYSTEMS/UNITOP
331 - GoTop Super_Q2/GogoPen/PenPower tablets
333 Have a look at <http://linux.chapter7.ch/touchkit/> for
334 a usage description and the required user-space stuff.
336 To compile this driver as a module, choose M here: the
337 module will be called usbtouchscreen.
339 config TOUCHSCREEN_USB_EGALAX
341 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
342 depends on TOUCHSCREEN_USB_COMPOSITE
344 config TOUCHSCREEN_USB_PANJIT
346 bool "PanJit device support" if EMBEDDED
347 depends on TOUCHSCREEN_USB_COMPOSITE
349 config TOUCHSCREEN_USB_3M
351 bool "3M/Microtouch EX II series device support" if EMBEDDED
352 depends on TOUCHSCREEN_USB_COMPOSITE
354 config TOUCHSCREEN_USB_ITM
356 bool "ITM device support" if EMBEDDED
357 depends on TOUCHSCREEN_USB_COMPOSITE
359 config TOUCHSCREEN_USB_ETURBO
361 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
362 depends on TOUCHSCREEN_USB_COMPOSITE
364 config TOUCHSCREEN_USB_GUNZE
366 bool "Gunze AHL61 device support" if EMBEDDED
367 depends on TOUCHSCREEN_USB_COMPOSITE
369 config TOUCHSCREEN_USB_DMC_TSC10
371 bool "DMC TSC-10/25 device support" if EMBEDDED
372 depends on TOUCHSCREEN_USB_COMPOSITE
374 config TOUCHSCREEN_USB_IRTOUCH
376 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
377 depends on TOUCHSCREEN_USB_COMPOSITE
379 config TOUCHSCREEN_USB_IDEALTEK
381 bool "IdealTEK URTC1000 device support" if EMBEDDED
382 depends on TOUCHSCREEN_USB_COMPOSITE
384 config TOUCHSCREEN_USB_GENERAL_TOUCH
386 bool "GeneralTouch Touchscreen device support" if EMBEDDED
387 depends on TOUCHSCREEN_USB_COMPOSITE
389 config TOUCHSCREEN_USB_GOTOP
391 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
392 depends on TOUCHSCREEN_USB_COMPOSITE
394 config TOUCHSCREEN_TOUCHIT213
395 tristate "Sahara TouchIT-213 touchscreen"
398 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
402 To compile this driver as a module, choose M here: the
403 module will be called touchit213.