drivers/char/synclink_gt.c

   1 /*
   2  * $Id: synclink_gt.c,v 4.25 2006/02/06 21:20:33 paulkf Exp $
   3  *
   4  * Device driver for Microgate SyncLink GT serial adapters.
   5  *
   6  * written by Paul Fulghum for Microgate Corporation
   7  * paulkf@microgate.com
   8  *
   9  * Microgate and SyncLink are trademarks of Microgate Corporation
  10  *
  11  * This code is released under the GNU General Public License (GPL)
  12  *
  13  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  14  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  15  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  16  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  17  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  18  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  19  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  20  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  21  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  22  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  23  * OF THE POSSIBILITY OF SUCH DAMAGE.
  24  */
  25
  26 /*
  27  * DEBUG OUTPUT DEFINITIONS
  28  *
  29  * uncomment lines below to enable specific types of debug output
  30  *
  31  * DBGINFO   information - most verbose output
  32  * DBGERR    serious errors
  33  * DBGBH     bottom half service routine debugging
  34  * DBGISR    interrupt service routine debugging
  35  * DBGDATA   output receive and transmit data
  36  * DBGTBUF   output transmit DMA buffers and registers
  37  * DBGRBUF   output receive DMA buffers and registers
  38  */
  39
  40 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  41 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  42 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  43 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  44 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  45 //#define DBGTBUF(info) dump_tbufs(info)
  46 //#define DBGRBUF(info) dump_rbufs(info)
  47
  48
  49 #include <linux/config.h>
  50 #include <linux/module.h>
  51 #include <linux/version.h>
  52 #include <linux/errno.h>
  53 #include <linux/signal.h>
  54 #include <linux/sched.h>
  55 #include <linux/timer.h>
  56 #include <linux/interrupt.h>
  57 #include <linux/pci.h>
  58 #include <linux/tty.h>
  59 #include <linux/tty_flip.h>
  60 #include <linux/serial.h>
  61 #include <linux/major.h>
  62 #include <linux/string.h>
  63 #include <linux/fcntl.h>
  64 #include <linux/ptrace.h>
  65 #include <linux/ioport.h>
  66 #include <linux/mm.h>
  67 #include <linux/slab.h>
  68 #include <linux/netdevice.h>
  69 #include <linux/vmalloc.h>
  70 #include <linux/init.h>
  71 #include <linux/delay.h>
  72 #include <linux/ioctl.h>
  73 #include <linux/termios.h>
  74 #include <linux/bitops.h>
  75 #include <linux/workqueue.h>
  76 #include <linux/hdlc.h>
  77
  78 #include <asm/system.h>
  79 #include <asm/io.h>
  80 #include <asm/irq.h>
  81 #include <asm/dma.h>
  82 #include <asm/types.h>
  83 #include <asm/uaccess.h>
  84
  85 #include "linux/synclink.h"
  86
  87 #ifdef CONFIG_HDLC_MODULE
  88 #define CONFIG_HDLC 1
  89 #endif
  90
  91 /*
  92  * module identification
  93  */
  94 static char *driver_name     = "SyncLink GT";
  95 static char *driver_version  = "$Revision: 4.25 $";
  96 static char *tty_driver_name = "synclink_gt";
  97 static char *tty_dev_prefix  = "ttySLG";
  98 MODULE_LICENSE("GPL");
  99 #define MGSL_MAGIC 0x5401
 100 #define MAX_DEVICES 12
 101
 102 static struct pci_device_id pci_table[] = {
 103         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 104         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 105         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 106         {0,}, /* terminate list */
 107 };
 108 MODULE_DEVICE_TABLE(pci, pci_table);
 109
 110 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 111 static void remove_one(struct pci_dev *dev);
 112 static struct pci_driver pci_driver = {
 113         .name           = "synclink_gt",
 114         .id_table       = pci_table,
 115         .probe          = init_one,
 116         .remove         = __devexit_p(remove_one),
 117 };
 118
 119 static int pci_registered;
 120
 121 /*
 122  * module configuration and status
 123  */
 124 static struct slgt_info *slgt_device_list;
 125 static int slgt_device_count;
 126
 127 static int ttymajor;
 128 static int debug_level;
 129 static int maxframe[MAX_DEVICES];
 130 static int dosyncppp[MAX_DEVICES];
 131
 132 module_param(ttymajor, int, 0);
 133 module_param(debug_level, int, 0);
 134 module_param_array(maxframe, int, NULL, 0);
 135 module_param_array(dosyncppp, int, NULL, 0);
 136
 137 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 138 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 139 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 140 MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
 141
 142 /*
 143  * tty support and callbacks
 144  */
 145 #define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
 146
 147 static struct tty_driver *serial_driver;
 148
 149 static int  open(struct tty_struct *tty, struct file * filp);
 150 static void close(struct tty_struct *tty, struct file * filp);
 151 static void hangup(struct tty_struct *tty);
 152 static void set_termios(struct tty_struct *tty, struct termios *old_termios);
 153
 154 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 155 static void put_char(struct tty_struct *tty, unsigned char ch);
 156 static void send_xchar(struct tty_struct *tty, char ch);
 157 static void wait_until_sent(struct tty_struct *tty, int timeout);
 158 static int  write_room(struct tty_struct *tty);
 159 static void flush_chars(struct tty_struct *tty);
 160 static void flush_buffer(struct tty_struct *tty);
 161 static void tx_hold(struct tty_struct *tty);
 162 static void tx_release(struct tty_struct *tty);
 163
 164 static int  ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
 165 static int  read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
 166 static int  chars_in_buffer(struct tty_struct *tty);
 167 static void throttle(struct tty_struct * tty);
 168 static void unthrottle(struct tty_struct * tty);
 169 static void set_break(struct tty_struct *tty, int break_state);
 170
 171 /*
 172  * generic HDLC support and callbacks
 173  */
 174 #ifdef CONFIG_HDLC
 175 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 176 static void hdlcdev_tx_done(struct slgt_info *info);
 177 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 178 static int  hdlcdev_init(struct slgt_info *info);
 179 static void hdlcdev_exit(struct slgt_info *info);
 180 #endif
 181
 182
 183 /*
 184  * device specific structures, macros and functions
 185  */
 186
 187 #define SLGT_MAX_PORTS 4
 188 #define SLGT_REG_SIZE  256
 189
 190 /*
 191  * conditional wait facility
 192  */
 193 struct cond_wait {
 194         struct cond_wait *next;
 195         wait_queue_head_t q;
 196         wait_queue_t wait;
 197         unsigned int data;
 198 };
 199 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 200 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 201 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 202 static void flush_cond_wait(struct cond_wait **head);
 203
 204 /*
 205  * DMA buffer descriptor and access macros
 206  */
 207 struct slgt_desc
 208 {
 209         unsigned short count;
 210         unsigned short status;
 211         unsigned int pbuf;  /* physical address of data buffer */
 212         unsigned int next;  /* physical address of next descriptor */
 213
 214         /* driver book keeping */
 215         char *buf;          /* virtual  address of data buffer */
 216         unsigned int pdesc; /* physical address of this descriptor */
 217         dma_addr_t buf_dma_addr;
 218 };
 219
 220 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 221 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 222 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 223 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 224 #define desc_count(a)      (le16_to_cpu((a).count))
 225 #define desc_status(a)     (le16_to_cpu((a).status))
 226 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 227 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 228 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 229 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 230 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 231
 232 struct _input_signal_events {
 233         int ri_up;
 234         int ri_down;
 235         int dsr_up;
 236         int dsr_down;
 237         int dcd_up;
 238         int dcd_down;
 239         int cts_up;
 240         int cts_down;
 241 };
 242
 243 /*
 244  * device instance data structure
 245  */
 246 struct slgt_info {
 247         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 248
 249         struct slgt_info *next_device;  /* device list link */
 250
 251         int magic;
 252         int flags;
 253
 254         char device_name[25];
 255         struct pci_dev *pdev;
 256
 257         int port_count;  /* count of ports on adapter */
 258         int adapter_num; /* adapter instance number */
 259         int port_num;    /* port instance number */
 260
 261         /* array of pointers to port contexts on this adapter */
 262         struct slgt_info *port_array[SLGT_MAX_PORTS];
 263
 264         int                     count;          /* count of opens */
 265         int                     line;           /* tty line instance number */
 266         unsigned short          close_delay;
 267         unsigned short          closing_wait;   /* time to wait before closing */
 268
 269         struct mgsl_icount      icount;
 270
 271         struct tty_struct       *tty;
 272         int                     timeout;
 273         int                     x_char;         /* xon/xoff character */
 274         int                     blocked_open;   /* # of blocked opens */
 275         unsigned int            read_status_mask;
 276         unsigned int            ignore_status_mask;
 277
 278         wait_queue_head_t       open_wait;
 279         wait_queue_head_t       close_wait;
 280
 281         wait_queue_head_t       status_event_wait_q;
 282         wait_queue_head_t       event_wait_q;
 283         struct timer_list       tx_timer;
 284         struct timer_list       rx_timer;
 285
 286         unsigned int            gpio_present;
 287         struct cond_wait        *gpio_wait_q;
 288
 289         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 290
 291         struct work_struct task;
 292         u32 pending_bh;
 293         int bh_requested;
 294         int bh_running;
 295
 296         int isr_overflow;
 297         int irq_requested;      /* nonzero if IRQ requested */
 298         int irq_occurred;       /* for diagnostics use */
 299
 300         /* device configuration */
 301
 302         unsigned int bus_type;
 303         unsigned int irq_level;
 304         unsigned long irq_flags;
 305
 306         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 307         u32 phys_reg_addr;
 308         int reg_addr_requested;
 309
 310         MGSL_PARAMS params;       /* communications parameters */
 311         u32 idle_mode;
 312         u32 max_frame_size;       /* as set by device config */
 313
 314         unsigned int raw_rx_size;
 315         unsigned int if_mode;
 316
 317         /* device status */
 318
 319         int rx_enabled;
 320         int rx_restart;
 321
 322         int tx_enabled;
 323         int tx_active;
 324
 325         unsigned char signals;    /* serial signal states */
 326         int init_error;  /* initialization error */
 327
 328         unsigned char *tx_buf;
 329         int tx_count;
 330
 331         char flag_buf[MAX_ASYNC_BUFFER_SIZE];
 332         char char_buf[MAX_ASYNC_BUFFER_SIZE];
 333         BOOLEAN drop_rts_on_tx_done;
 334         struct  _input_signal_events    input_signal_events;
 335
 336         int dcd_chkcount;       /* check counts to prevent */
 337         int cts_chkcount;       /* too many IRQs if a signal */
 338         int dsr_chkcount;       /* is floating */
 339         int ri_chkcount;
 340
 341         char *bufs;             /* virtual address of DMA buffer lists */
 342         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 343
 344         unsigned int rbuf_count;
 345         struct slgt_desc *rbufs;
 346         unsigned int rbuf_current;
 347         unsigned int rbuf_index;
 348
 349         unsigned int tbuf_count;
 350         struct slgt_desc *tbufs;
 351         unsigned int tbuf_current;
 352         unsigned int tbuf_start;
 353
 354         unsigned char *tmp_rbuf;
 355         unsigned int tmp_rbuf_count;
 356
 357         /* SPPP/Cisco HDLC device parts */
 358
 359         int netcount;
 360         int dosyncppp;
 361         spinlock_t netlock;
 362 #ifdef CONFIG_HDLC
 363         struct net_device *netdev;
 364 #endif
 365
 366 };
 367
 368 static MGSL_PARAMS default_params = {
 369         .mode            = MGSL_MODE_HDLC,
 370         .loopback        = 0,
 371         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 372         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 373         .clock_speed     = 0,
 374         .addr_filter     = 0xff,
 375         .crc_type        = HDLC_CRC_16_CCITT,
 376         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 377         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 378         .data_rate       = 9600,
 379         .data_bits       = 8,
 380         .stop_bits       = 1,
 381         .parity          = ASYNC_PARITY_NONE
 382 };
 383
 384
 385 #define BH_RECEIVE  1
 386 #define BH_TRANSMIT 2
 387 #define BH_STATUS   4
 388 #define IO_PIN_SHUTDOWN_LIMIT 100
 389
 390 #define DMABUFSIZE 256
 391 #define DESC_LIST_SIZE 4096
 392
 393 #define MASK_PARITY  BIT1
 394 #define MASK_FRAMING BIT2
 395 #define MASK_BREAK   BIT3
 396 #define MASK_OVERRUN BIT4
 397
 398 #define GSR   0x00 /* global status */
 399 #define JCR   0x04 /* JTAG control */
 400 #define IODR  0x08 /* GPIO direction */
 401 #define IOER  0x0c /* GPIO interrupt enable */
 402 #define IOVR  0x10 /* GPIO value */
 403 #define IOSR  0x14 /* GPIO interrupt status */
 404 #define TDR   0x80 /* tx data */
 405 #define RDR   0x80 /* rx data */
 406 #define TCR   0x82 /* tx control */
 407 #define TIR   0x84 /* tx idle */
 408 #define TPR   0x85 /* tx preamble */
 409 #define RCR   0x86 /* rx control */
 410 #define VCR   0x88 /* V.24 control */
 411 #define CCR   0x89 /* clock control */
 412 #define BDR   0x8a /* baud divisor */
 413 #define SCR   0x8c /* serial control */
 414 #define SSR   0x8e /* serial status */
 415 #define RDCSR 0x90 /* rx DMA control/status */
 416 #define TDCSR 0x94 /* tx DMA control/status */
 417 #define RDDAR 0x98 /* rx DMA descriptor address */
 418 #define TDDAR 0x9c /* tx DMA descriptor address */
 419
 420 #define RXIDLE      BIT14
 421 #define RXBREAK     BIT14
 422 #define IRQ_TXDATA  BIT13
 423 #define IRQ_TXIDLE  BIT12
 424 #define IRQ_TXUNDER BIT11 /* HDLC */
 425 #define IRQ_RXDATA  BIT10
 426 #define IRQ_RXIDLE  BIT9  /* HDLC */
 427 #define IRQ_RXBREAK BIT9  /* async */
 428 #define IRQ_RXOVER  BIT8
 429 #define IRQ_DSR     BIT7
 430 #define IRQ_CTS     BIT6
 431 #define IRQ_DCD     BIT5
 432 #define IRQ_RI      BIT4
 433 #define IRQ_ALL     0x3ff0
 434 #define IRQ_MASTER  BIT0
 435
 436 #define slgt_irq_on(info, mask) \
 437         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 438 #define slgt_irq_off(info, mask) \
 439         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 440
 441 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 442 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 443 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 444 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 445 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 446 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 447
 448 static void  msc_set_vcr(struct slgt_info *info);
 449
 450 static int  startup(struct slgt_info *info);
 451 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 452 static void shutdown(struct slgt_info *info);
 453 static void program_hw(struct slgt_info *info);
 454 static void change_params(struct slgt_info *info);
 455
 456 static int  register_test(struct slgt_info *info);
 457 static int  irq_test(struct slgt_info *info);
 458 static int  loopback_test(struct slgt_info *info);
 459 static int  adapter_test(struct slgt_info *info);
 460
 461 static void reset_adapter(struct slgt_info *info);
 462 static void reset_port(struct slgt_info *info);
 463 static void async_mode(struct slgt_info *info);
 464 static void hdlc_mode(struct slgt_info *info);
 465
 466 static void rx_stop(struct slgt_info *info);
 467 static void rx_start(struct slgt_info *info);
 468 static void reset_rbufs(struct slgt_info *info);
 469 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 470 static void rdma_reset(struct slgt_info *info);
 471 static int  rx_get_frame(struct slgt_info *info);
 472 static int  rx_get_buf(struct slgt_info *info);
 473
 474 static void tx_start(struct slgt_info *info);
 475 static void tx_stop(struct slgt_info *info);
 476 static void tx_set_idle(struct slgt_info *info);
 477 static unsigned int free_tbuf_count(struct slgt_info *info);
 478 static void reset_tbufs(struct slgt_info *info);
 479 static void tdma_reset(struct slgt_info *info);
 480 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 481
 482 static void get_signals(struct slgt_info *info);
 483 static void set_signals(struct slgt_info *info);
 484 static void enable_loopback(struct slgt_info *info);
 485 static void set_rate(struct slgt_info *info, u32 data_rate);
 486
 487 static int  bh_action(struct slgt_info *info);
 488 static void bh_handler(void* context);
 489 static void bh_transmit(struct slgt_info *info);
 490 static void isr_serial(struct slgt_info *info);
 491 static void isr_rdma(struct slgt_info *info);
 492 static void isr_txeom(struct slgt_info *info, unsigned short status);
 493 static void isr_tdma(struct slgt_info *info);
 494 static irqreturn_t slgt_interrupt(int irq, void *dev_id, struct pt_regs * regs);
 495
 496 static int  alloc_dma_bufs(struct slgt_info *info);
 497 static void free_dma_bufs(struct slgt_info *info);
 498 static int  alloc_desc(struct slgt_info *info);
 499 static void free_desc(struct slgt_info *info);
 500 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 501 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 502
 503 static int  alloc_tmp_rbuf(struct slgt_info *info);
 504 static void free_tmp_rbuf(struct slgt_info *info);
 505
 506 static void tx_timeout(unsigned long context);
 507 static void rx_timeout(unsigned long context);
 508
 509 /*
 510  * ioctl handlers
 511  */
 512 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 513 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 514 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 515 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 516 static int  set_txidle(struct slgt_info *info, int idle_mode);
 517 static int  tx_enable(struct slgt_info *info, int enable);
 518 static int  tx_abort(struct slgt_info *info);
 519 static int  rx_enable(struct slgt_info *info, int enable);
 520 static int  modem_input_wait(struct slgt_info *info,int arg);
 521 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 522 static int  tiocmget(struct tty_struct *tty, struct file *file);
 523 static int  tiocmset(struct tty_struct *tty, struct file *file,
 524                      unsigned int set, unsigned int clear);
 525 static void set_break(struct tty_struct *tty, int break_state);
 526 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 527 static int  set_interface(struct slgt_info *info, int if_mode);
 528 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 529 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 530 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 531
 532 /*
 533  * driver functions
 534  */
 535 static void add_device(struct slgt_info *info);
 536 static void device_init(int adapter_num, struct pci_dev *pdev);
 537 static int  claim_resources(struct slgt_info *info);
 538 static void release_resources(struct slgt_info *info);
 539
 540 /*
 541  * DEBUG OUTPUT CODE
 542  */
 543 #ifndef DBGINFO
 544 #define DBGINFO(fmt)
 545 #endif
 546 #ifndef DBGERR
 547 #define DBGERR(fmt)
 548 #endif
 549 #ifndef DBGBH
 550 #define DBGBH(fmt)
 551 #endif
 552 #ifndef DBGISR
 553 #define DBGISR(fmt)
 554 #endif
 555
 556 #ifdef DBGDATA
 557 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 558 {
 559         int i;
 560         int linecount;
 561         printk("%s %s data:\n",info->device_name, label);
 562         while(count) {
 563                 linecount = (count > 16) ? 16 : count;
 564                 for(i=0; i < linecount; i++)
 565                         printk("%02X ",(unsigned char)data[i]);
 566                 for(;i<17;i++)
 567                         printk("   ");
 568                 for(i=0;i<linecount;i++) {
 569                         if (data[i]>=040 && data[i]<=0176)
 570                                 printk("%c",data[i]);
 571                         else
 572                                 printk(".");
 573                 }
 574                 printk("\n");
 575                 data  += linecount;
 576                 count -= linecount;
 577         }
 578 }
 579 #else
 580 #define DBGDATA(info, buf, size, label)
 581 #endif
 582
 583 #ifdef DBGTBUF
 584 static void dump_tbufs(struct slgt_info *info)
 585 {
 586         int i;
 587         printk("tbuf_current=%d\n", info->tbuf_current);
 588         for (i=0 ; i < info->tbuf_count ; i++) {
 589                 printk("%d: count=%04X status=%04X\n",
 590                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 591         }
 592 }
 593 #else
 594 #define DBGTBUF(info)
 595 #endif
 596
 597 #ifdef DBGRBUF
 598 static void dump_rbufs(struct slgt_info *info)
 599 {
 600         int i;
 601         printk("rbuf_current=%d\n", info->rbuf_current);
 602         for (i=0 ; i < info->rbuf_count ; i++) {
 603                 printk("%d: count=%04X status=%04X\n",
 604                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 605         }
 606 }
 607 #else
 608 #define DBGRBUF(info)
 609 #endif
 610
 611 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 612 {
 613 #ifdef SANITY_CHECK
 614         if (!info) {
 615                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 616                 return 1;
 617         }
 618         if (info->magic != MGSL_MAGIC) {
 619                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 620                 return 1;
 621         }
 622 #else
 623         if (!info)
 624                 return 1;
 625 #endif
 626         return 0;
 627 }
 628
 629 /**
 630  * line discipline callback wrappers
 631  *
 632  * The wrappers maintain line discipline references
 633  * while calling into the line discipline.
 634  *
 635  * ldisc_receive_buf  - pass receive data to line discipline
 636  */
 637 static void ldisc_receive_buf(struct tty_struct *tty,
 638                               const __u8 *data, char *flags, int count)
 639 {
 640         struct tty_ldisc *ld;
 641         if (!tty)
 642                 return;
 643         ld = tty_ldisc_ref(tty);
 644         if (ld) {
 645                 if (ld->receive_buf)
 646                         ld->receive_buf(tty, data, flags, count);
 647                 tty_ldisc_deref(ld);
 648         }
 649 }
 650
 651 /* tty callbacks */
 652
 653 static int open(struct tty_struct *tty, struct file *filp)
 654 {
 655         struct slgt_info *info;
 656         int retval, line;
 657         unsigned long flags;
 658
 659         line = tty->index;
 660         if ((line < 0) || (line >= slgt_device_count)) {
 661                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 662                 return -ENODEV;
 663         }
 664
 665         info = slgt_device_list;
 666         while(info && info->line != line)
 667                 info = info->next_device;
 668         if (sanity_check(info, tty->name, "open"))
 669                 return -ENODEV;
 670         if (info->init_error) {
 671                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 672                 return -ENODEV;
 673         }
 674
 675         tty->driver_data = info;
 676         info->tty = tty;
 677
 678         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->count));
 679
 680         /* If port is closing, signal caller to try again */
 681         if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){
 682                 if (info->flags & ASYNC_CLOSING)
 683                         interruptible_sleep_on(&info->close_wait);
 684                 retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
 685                         -EAGAIN : -ERESTARTSYS);
 686                 goto cleanup;
 687         }
 688
 689         info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 690
 691         spin_lock_irqsave(&info->netlock, flags);
 692         if (info->netcount) {
 693                 retval = -EBUSY;
 694                 spin_unlock_irqrestore(&info->netlock, flags);
 695                 goto cleanup;
 696         }
 697         info->count++;
 698         spin_unlock_irqrestore(&info->netlock, flags);
 699
 700         if (info->count == 1) {
 701                 /* 1st open on this device, init hardware */
 702                 retval = startup(info);
 703                 if (retval < 0)
 704                         goto cleanup;
 705         }
 706
 707         retval = block_til_ready(tty, filp, info);
 708         if (retval) {
 709                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 710                 goto cleanup;
 711         }
 712
 713         retval = 0;
 714
 715 cleanup:
 716         if (retval) {
 717                 if (tty->count == 1)
 718                         info->tty = NULL; /* tty layer will release tty struct */
 719                 if(info->count)
 720                         info->count--;
 721         }
 722
 723         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 724         return retval;
 725 }
 726
 727 static void close(struct tty_struct *tty, struct file *filp)
 728 {
 729         struct slgt_info *info = tty->driver_data;
 730
 731         if (sanity_check(info, tty->name, "close"))
 732                 return;
 733         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->count));
 734
 735         if (!info->count)
 736                 return;
 737
 738         if (tty_hung_up_p(filp))
 739                 goto cleanup;
 740
 741         if ((tty->count == 1) && (info->count != 1)) {
 742                 /*
 743                  * tty->count is 1 and the tty structure will be freed.
 744                  * info->count should be one in this case.
 745                  * if it's not, correct it so that the port is shutdown.
 746                  */
 747                 DBGERR(("%s close: bad refcount; tty->count=1, "
 748                        "info->count=%d\n", info->device_name, info->count));
 749                 info->count = 1;
 750         }
 751
 752         info->count--;
 753
 754         /* if at least one open remaining, leave hardware active */
 755         if (info->count)
 756                 goto cleanup;
 757
 758         info->flags |= ASYNC_CLOSING;
 759
 760         /* set tty->closing to notify line discipline to
 761          * only process XON/XOFF characters. Only the N_TTY
 762          * discipline appears to use this (ppp does not).
 763          */
 764         tty->closing = 1;
 765
 766         /* wait for transmit data to clear all layers */
 767
 768         if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
 769                 DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
 770                 tty_wait_until_sent(tty, info->closing_wait);
 771         }
 772
 773         if (info->flags & ASYNC_INITIALIZED)
 774                 wait_until_sent(tty, info->timeout);
 775         if (tty->driver->flush_buffer)
 776                 tty->driver->flush_buffer(tty);
 777         tty_ldisc_flush(tty);
 778
 779         shutdown(info);
 780
 781         tty->closing = 0;
 782         info->tty = NULL;
 783
 784         if (info->blocked_open) {
 785                 if (info->close_delay) {
 786                         msleep_interruptible(jiffies_to_msecs(info->close_delay));
 787                 }
 788                 wake_up_interruptible(&info->open_wait);
 789         }
 790
 791         info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
 792
 793         wake_up_interruptible(&info->close_wait);
 794
 795 cleanup:
 796         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->count));
 797 }
 798
 799 static void hangup(struct tty_struct *tty)
 800 {
 801         struct slgt_info *info = tty->driver_data;
 802
 803         if (sanity_check(info, tty->name, "hangup"))
 804                 return;
 805         DBGINFO(("%s hangup\n", info->device_name));
 806
 807         flush_buffer(tty);
 808         shutdown(info);
 809
 810         info->count = 0;
 811         info->flags &= ~ASYNC_NORMAL_ACTIVE;
 812         info->tty = NULL;
 813
 814         wake_up_interruptible(&info->open_wait);
 815 }
 816
 817 static void set_termios(struct tty_struct *tty, struct termios *old_termios)
 818 {
 819         struct slgt_info *info = tty->driver_data;
 820         unsigned long flags;
 821
 822         DBGINFO(("%s set_termios\n", tty->driver->name));
 823
 824         /* just return if nothing has changed */
 825         if ((tty->termios->c_cflag == old_termios->c_cflag)
 826             && (RELEVANT_IFLAG(tty->termios->c_iflag)
 827                 == RELEVANT_IFLAG(old_termios->c_iflag)))
 828                 return;
 829
 830         change_params(info);
 831
 832         /* Handle transition to B0 status */
 833         if (old_termios->c_cflag & CBAUD &&
 834             !(tty->termios->c_cflag & CBAUD)) {
 835                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 836                 spin_lock_irqsave(&info->lock,flags);
 837                 set_signals(info);
 838                 spin_unlock_irqrestore(&info->lock,flags);
 839         }
 840
 841         /* Handle transition away from B0 status */
 842         if (!(old_termios->c_cflag & CBAUD) &&
 843             tty->termios->c_cflag & CBAUD) {
 844                 info->signals |= SerialSignal_DTR;
 845                 if (!(tty->termios->c_cflag & CRTSCTS) ||
 846                     !test_bit(TTY_THROTTLED, &tty->flags)) {
 847                         info->signals |= SerialSignal_RTS;
 848                 }
 849                 spin_lock_irqsave(&info->lock,flags);
 850                 set_signals(info);
 851                 spin_unlock_irqrestore(&info->lock,flags);
 852         }
 853
 854         /* Handle turning off CRTSCTS */
 855         if (old_termios->c_cflag & CRTSCTS &&
 856             !(tty->termios->c_cflag & CRTSCTS)) {
 857                 tty->hw_stopped = 0;
 858                 tx_release(tty);
 859         }
 860 }
 861
 862 static int write(struct tty_struct *tty,
 863                  const unsigned char *buf, int count)
 864 {
 865         int ret = 0;
 866         struct slgt_info *info = tty->driver_data;
 867         unsigned long flags;
 868
 869         if (sanity_check(info, tty->name, "write"))
 870                 goto cleanup;
 871         DBGINFO(("%s write count=%d\n", info->device_name, count));
 872
 873         if (!tty || !info->tx_buf)
 874                 goto cleanup;
 875
 876         if (count > info->max_frame_size) {
 877                 ret = -EIO;
 878                 goto cleanup;
 879         }
 880
 881         if (!count)
 882                 goto cleanup;
 883
 884         if (info->params.mode == MGSL_MODE_RAW) {
 885                 unsigned int bufs_needed = (count/DMABUFSIZE);
 886                 unsigned int bufs_free = free_tbuf_count(info);
 887                 if (count % DMABUFSIZE)
 888                         ++bufs_needed;
 889                 if (bufs_needed > bufs_free)
 890                         goto cleanup;
 891         } else {
 892                 if (info->tx_active)
 893                         goto cleanup;
 894                 if (info->tx_count) {
 895                         /* send accumulated data from send_char() calls */
 896                         /* as frame and wait before accepting more data. */
 897                         tx_load(info, info->tx_buf, info->tx_count);
 898                         goto start;
 899                 }
 900         }
 901
 902         ret = info->tx_count = count;
 903         tx_load(info, buf, count);
 904         goto start;
 905
 906 start:
 907         if (info->tx_count && !tty->stopped && !tty->hw_stopped) {
 908                 spin_lock_irqsave(&info->lock,flags);
 909                 if (!info->tx_active)
 910                         tx_start(info);
 911                 spin_unlock_irqrestore(&info->lock,flags);
 912         }
 913
 914 cleanup:
 915         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 916         return ret;
 917 }
 918
 919 static void put_char(struct tty_struct *tty, unsigned char ch)
 920 {
 921         struct slgt_info *info = tty->driver_data;
 922         unsigned long flags;
 923
 924         if (sanity_check(info, tty->name, "put_char"))
 925                 return;
 926         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 927         if (!tty || !info->tx_buf)
 928                 return;
 929         spin_lock_irqsave(&info->lock,flags);
 930         if (!info->tx_active && (info->tx_count < info->max_frame_size))
 931                 info->tx_buf[info->tx_count++] = ch;
 932         spin_unlock_irqrestore(&info->lock,flags);
 933 }
 934
 935 static void send_xchar(struct tty_struct *tty, char ch)
 936 {
 937         struct slgt_info *info = tty->driver_data;
 938         unsigned long flags;
 939
 940         if (sanity_check(info, tty->name, "send_xchar"))
 941                 return;
 942         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 943         info->x_char = ch;
 944         if (ch) {
 945                 spin_lock_irqsave(&info->lock,flags);
 946                 if (!info->tx_enabled)
 947                         tx_start(info);
 948                 spin_unlock_irqrestore(&info->lock,flags);
 949         }
 950 }
 951
 952 static void wait_until_sent(struct tty_struct *tty, int timeout)
 953 {
 954         struct slgt_info *info = tty->driver_data;
 955         unsigned long orig_jiffies, char_time;
 956
 957         if (!info )
 958                 return;
 959         if (sanity_check(info, tty->name, "wait_until_sent"))
 960                 return;
 961         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 962         if (!(info->flags & ASYNC_INITIALIZED))
 963                 goto exit;
 964
 965         orig_jiffies = jiffies;
 966
 967         /* Set check interval to 1/5 of estimated time to
 968          * send a character, and make it at least 1. The check
 969          * interval should also be less than the timeout.
 970          * Note: use tight timings here to satisfy the NIST-PCTS.
 971          */
 972
 973         if (info->params.data_rate) {
 974                 char_time = info->timeout/(32 * 5);
 975                 if (!char_time)
 976                         char_time++;
 977         } else
 978                 char_time = 1;
 979
 980         if (timeout)
 981                 char_time = min_t(unsigned long, char_time, timeout);
 982
 983         while (info->tx_active) {
 984                 msleep_interruptible(jiffies_to_msecs(char_time));
 985                 if (signal_pending(current))
 986                         break;
 987                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 988                         break;
 989         }
 990
 991 exit:
 992         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 993 }
 994
 995 static int write_room(struct tty_struct *tty)
 996 {
 997         struct slgt_info *info = tty->driver_data;
 998         int ret;
 999
1000         if (sanity_check(info, tty->name, "write_room"))
1001                 return 0;
1002         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
1003         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
1004         return ret;
1005 }
1006
1007 static void flush_chars(struct tty_struct *tty)
1008 {
1009         struct slgt_info *info = tty->driver_data;
1010         unsigned long flags;
1011
1012         if (sanity_check(info, tty->name, "flush_chars"))
1013                 return;
1014         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
1015
1016         if (info->tx_count <= 0 || tty->stopped ||
1017             tty->hw_stopped || !info->tx_buf)
1018                 return;
1019
1020         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
1021
1022         spin_lock_irqsave(&info->lock,flags);
1023         if (!info->tx_active && info->tx_count) {
1024                 tx_load(info, info->tx_buf,info->tx_count);
1025                 tx_start(info);
1026         }
1027         spin_unlock_irqrestore(&info->lock,flags);
1028 }
1029
1030 static void flush_buffer(struct tty_struct *tty)
1031 {
1032         struct slgt_info *info = tty->driver_data;
1033         unsigned long flags;
1034
1035         if (sanity_check(info, tty->name, "flush_buffer"))
1036                 return;
1037         DBGINFO(("%s flush_buffer\n", info->device_name));
1038
1039         spin_lock_irqsave(&info->lock,flags);
1040         if (!info->tx_active)
1041                 info->tx_count = 0;
1042         spin_unlock_irqrestore(&info->lock,flags);
1043
1044         wake_up_interruptible(&tty->write_wait);
1045         tty_wakeup(tty);
1046 }
1047
1048 /*
1049  * throttle (stop) transmitter
1050  */
1051 static void tx_hold(struct tty_struct *tty)
1052 {
1053         struct slgt_info *info = tty->driver_data;
1054         unsigned long flags;
1055
1056         if (sanity_check(info, tty->name, "tx_hold"))
1057                 return;
1058         DBGINFO(("%s tx_hold\n", info->device_name));
1059         spin_lock_irqsave(&info->lock,flags);
1060         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1061                 tx_stop(info);
1062         spin_unlock_irqrestore(&info->lock,flags);
1063 }
1064
1065 /*
1066  * release (start) transmitter
1067  */
1068 static void tx_release(struct tty_struct *tty)
1069 {
1070         struct slgt_info *info = tty->driver_data;
1071         unsigned long flags;
1072
1073         if (sanity_check(info, tty->name, "tx_release"))
1074                 return;
1075         DBGINFO(("%s tx_release\n", info->device_name));
1076         spin_lock_irqsave(&info->lock,flags);
1077         if (!info->tx_active && info->tx_count) {
1078                 tx_load(info, info->tx_buf, info->tx_count);
1079                 tx_start(info);
1080         }
1081         spin_unlock_irqrestore(&info->lock,flags);
1082 }
1083
1084 /*
1085  * Service an IOCTL request
1086  *
1087  * Arguments
1088  *
1089  *      tty     pointer to tty instance data
1090  *      file    pointer to associated file object for device
1091  *      cmd     IOCTL command code
1092  *      arg     command argument/context
1093  *
1094  * Return 0 if success, otherwise error code
1095  */
1096 static int ioctl(struct tty_struct *tty, struct file *file,
1097                  unsigned int cmd, unsigned long arg)
1098 {
1099         struct slgt_info *info = tty->driver_data;
1100         struct mgsl_icount cnow;        /* kernel counter temps */
1101         struct serial_icounter_struct __user *p_cuser;  /* user space */
1102         unsigned long flags;
1103         void __user *argp = (void __user *)arg;
1104
1105         if (sanity_check(info, tty->name, "ioctl"))
1106                 return -ENODEV;
1107         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1108
1109         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1110             (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
1111                 if (tty->flags & (1 << TTY_IO_ERROR))
1112                     return -EIO;
1113         }
1114
1115         switch (cmd) {
1116         case MGSL_IOCGPARAMS:
1117                 return get_params(info, argp);
1118         case MGSL_IOCSPARAMS:
1119                 return set_params(info, argp);
1120         case MGSL_IOCGTXIDLE:
1121                 return get_txidle(info, argp);
1122         case MGSL_IOCSTXIDLE:
1123                 return set_txidle(info, (int)arg);
1124         case MGSL_IOCTXENABLE:
1125                 return tx_enable(info, (int)arg);
1126         case MGSL_IOCRXENABLE:
1127                 return rx_enable(info, (int)arg);
1128         case MGSL_IOCTXABORT:
1129                 return tx_abort(info);
1130         case MGSL_IOCGSTATS:
1131                 return get_stats(info, argp);
1132         case MGSL_IOCWAITEVENT:
1133                 return wait_mgsl_event(info, argp);
1134         case TIOCMIWAIT:
1135                 return modem_input_wait(info,(int)arg);
1136         case MGSL_IOCGIF:
1137                 return get_interface(info, argp);
1138         case MGSL_IOCSIF:
1139                 return set_interface(info,(int)arg);
1140         case MGSL_IOCSGPIO:
1141                 return set_gpio(info, argp);
1142         case MGSL_IOCGGPIO:
1143                 return get_gpio(info, argp);
1144         case MGSL_IOCWAITGPIO:
1145                 return wait_gpio(info, argp);
1146         case TIOCGICOUNT:
1147                 spin_lock_irqsave(&info->lock,flags);
1148                 cnow = info->icount;
1149                 spin_unlock_irqrestore(&info->lock,flags);
1150                 p_cuser = argp;
1151                 if (put_user(cnow.cts, &p_cuser->cts) ||
1152                     put_user(cnow.dsr, &p_cuser->dsr) ||
1153                     put_user(cnow.rng, &p_cuser->rng) ||
1154                     put_user(cnow.dcd, &p_cuser->dcd) ||
1155                     put_user(cnow.rx, &p_cuser->rx) ||
1156                     put_user(cnow.tx, &p_cuser->tx) ||
1157                     put_user(cnow.frame, &p_cuser->frame) ||
1158                     put_user(cnow.overrun, &p_cuser->overrun) ||
1159                     put_user(cnow.parity, &p_cuser->parity) ||
1160                     put_user(cnow.brk, &p_cuser->brk) ||
1161                     put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
1162                         return -EFAULT;
1163                 return 0;
1164         default:
1165                 return -ENOIOCTLCMD;
1166         }
1167         return 0;
1168 }
1169
1170 /*
1171  * proc fs support
1172  */
1173 static inline int line_info(char *buf, struct slgt_info *info)
1174 {
1175         char stat_buf[30];
1176         int ret;
1177         unsigned long flags;
1178
1179         ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1180                       info->device_name, info->phys_reg_addr,
1181                       info->irq_level, info->max_frame_size);
1182
1183         /* output current serial signal states */
1184         spin_lock_irqsave(&info->lock,flags);
1185         get_signals(info);
1186         spin_unlock_irqrestore(&info->lock,flags);
1187
1188         stat_buf[0] = 0;
1189         stat_buf[1] = 0;
1190         if (info->signals & SerialSignal_RTS)
1191                 strcat(stat_buf, "|RTS");
1192         if (info->signals & SerialSignal_CTS)
1193                 strcat(stat_buf, "|CTS");
1194         if (info->signals & SerialSignal_DTR)
1195                 strcat(stat_buf, "|DTR");
1196         if (info->signals & SerialSignal_DSR)
1197                 strcat(stat_buf, "|DSR");
1198         if (info->signals & SerialSignal_DCD)
1199                 strcat(stat_buf, "|CD");
1200         if (info->signals & SerialSignal_RI)
1201                 strcat(stat_buf, "|RI");
1202
1203         if (info->params.mode != MGSL_MODE_ASYNC) {
1204                 ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
1205                                info->icount.txok, info->icount.rxok);
1206                 if (info->icount.txunder)
1207                         ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
1208                 if (info->icount.txabort)
1209                         ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
1210                 if (info->icount.rxshort)
1211                         ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
1212                 if (info->icount.rxlong)
1213                         ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
1214                 if (info->icount.rxover)
1215                         ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
1216                 if (info->icount.rxcrc)
1217                         ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
1218         } else {
1219                 ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
1220                                info->icount.tx, info->icount.rx);
1221                 if (info->icount.frame)
1222                         ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
1223                 if (info->icount.parity)
1224                         ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
1225                 if (info->icount.brk)
1226                         ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
1227                 if (info->icount.overrun)
1228                         ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
1229         }
1230
1231         /* Append serial signal status to end */
1232         ret += sprintf(buf+ret, " %s\n", stat_buf+1);
1233
1234         ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1235                        info->tx_active,info->bh_requested,info->bh_running,
1236                        info->pending_bh);
1237
1238         return ret;
1239 }
1240
1241 /* Called to print information about devices
1242  */
1243 static int read_proc(char *page, char **start, off_t off, int count,
1244                      int *eof, void *data)
1245 {
1246         int len = 0, l;
1247         off_t   begin = 0;
1248         struct slgt_info *info;
1249
1250         len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
1251
1252         info = slgt_device_list;
1253         while( info ) {
1254                 l = line_info(page + len, info);
1255                 len += l;
1256                 if (len+begin > off+count)
1257                         goto done;
1258                 if (len+begin < off) {
1259                         begin += len;
1260                         len = 0;
1261                 }
1262                 info = info->next_device;
1263         }
1264
1265         *eof = 1;
1266 done:
1267         if (off >= len+begin)
1268                 return 0;
1269         *start = page + (off-begin);
1270         return ((count < begin+len-off) ? count : begin+len-off);
1271 }
1272
1273 /*
1274  * return count of bytes in transmit buffer
1275  */
1276 static int chars_in_buffer(struct tty_struct *tty)
1277 {
1278         struct slgt_info *info = tty->driver_data;
1279         if (sanity_check(info, tty->name, "chars_in_buffer"))
1280                 return 0;
1281         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, info->tx_count));
1282         return info->tx_count;
1283 }
1284
1285 /*
1286  * signal remote device to throttle send data (our receive data)
1287  */
1288 static void throttle(struct tty_struct * tty)
1289 {
1290         struct slgt_info *info = tty->driver_data;
1291         unsigned long flags;
1292
1293         if (sanity_check(info, tty->name, "throttle"))
1294                 return;
1295         DBGINFO(("%s throttle\n", info->device_name));
1296         if (I_IXOFF(tty))
1297                 send_xchar(tty, STOP_CHAR(tty));
1298         if (tty->termios->c_cflag & CRTSCTS) {
1299                 spin_lock_irqsave(&info->lock,flags);
1300                 info->signals &= ~SerialSignal_RTS;
1301                 set_signals(info);
1302                 spin_unlock_irqrestore(&info->lock,flags);
1303         }
1304 }
1305
1306 /*
1307  * signal remote device to stop throttling send data (our receive data)
1308  */
1309 static void unthrottle(struct tty_struct * tty)
1310 {
1311         struct slgt_info *info = tty->driver_data;
1312         unsigned long flags;
1313
1314         if (sanity_check(info, tty->name, "unthrottle"))
1315                 return;
1316         DBGINFO(("%s unthrottle\n", info->device_name));
1317         if (I_IXOFF(tty)) {
1318                 if (info->x_char)
1319                         info->x_char = 0;
1320                 else
1321                         send_xchar(tty, START_CHAR(tty));
1322         }
1323         if (tty->termios->c_cflag & CRTSCTS) {
1324                 spin_lock_irqsave(&info->lock,flags);
1325                 info->signals |= SerialSignal_RTS;
1326                 set_signals(info);
1327                 spin_unlock_irqrestore(&info->lock,flags);
1328         }
1329 }
1330
1331 /*
1332  * set or clear transmit break condition
1333  * break_state  -1=set break condition, 0=clear
1334  */
1335 static void set_break(struct tty_struct *tty, int break_state)
1336 {
1337         struct slgt_info *info = tty->driver_data;
1338         unsigned short value;
1339         unsigned long flags;
1340
1341         if (sanity_check(info, tty->name, "set_break"))
1342                 return;
1343         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1344
1345         spin_lock_irqsave(&info->lock,flags);
1346         value = rd_reg16(info, TCR);
1347         if (break_state == -1)
1348                 value |= BIT6;
1349         else
1350                 value &= ~BIT6;
1351         wr_reg16(info, TCR, value);
1352         spin_unlock_irqrestore(&info->lock,flags);
1353 }
1354
1355 #ifdef CONFIG_HDLC
1356
1357 /**
1358  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1359  * set encoding and frame check sequence (FCS) options
1360  *
1361  * dev       pointer to network device structure
1362  * encoding  serial encoding setting
1363  * parity    FCS setting
1364  *
1365  * returns 0 if success, otherwise error code
1366  */
1367 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1368                           unsigned short parity)
1369 {
1370         struct slgt_info *info = dev_to_port(dev);
1371         unsigned char  new_encoding;
1372         unsigned short new_crctype;
1373
1374         /* return error if TTY interface open */
1375         if (info->count)
1376                 return -EBUSY;
1377
1378         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1379
1380         switch (encoding)
1381         {
1382         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1383         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1384         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1385         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1386         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1387         default: return -EINVAL;
1388         }
1389
1390         switch (parity)
1391         {
1392         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1393         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1394         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1395         default: return -EINVAL;
1396         }
1397
1398         info->params.encoding = new_encoding;
1399         info->params.crc_type = new_crctype;
1400
1401         /* if network interface up, reprogram hardware */
1402         if (info->netcount)
1403                 program_hw(info);
1404
1405         return 0;
1406 }
1407
1408 /**
1409  * called by generic HDLC layer to send frame
1410  *
1411  * skb  socket buffer containing HDLC frame
1412  * dev  pointer to network device structure
1413  *
1414  * returns 0 if success, otherwise error code
1415  */
1416 static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
1417 {
1418         struct slgt_info *info = dev_to_port(dev);
1419         struct net_device_stats *stats = hdlc_stats(dev);
1420         unsigned long flags;
1421
1422         DBGINFO(("%s hdlc_xmit\n", dev->name));
1423
1424         /* stop sending until this frame completes */
1425         netif_stop_queue(dev);
1426
1427         /* copy data to device buffers */
1428         info->tx_count = skb->len;
1429         tx_load(info, skb->data, skb->len);
1430
1431         /* update network statistics */
1432         stats->tx_packets++;
1433         stats->tx_bytes += skb->len;
1434
1435         /* done with socket buffer, so free it */
1436         dev_kfree_skb(skb);
1437
1438         /* save start time for transmit timeout detection */
1439         dev->trans_start = jiffies;
1440
1441         /* start hardware transmitter if necessary */
1442         spin_lock_irqsave(&info->lock,flags);
1443         if (!info->tx_active)
1444                 tx_start(info);
1445         spin_unlock_irqrestore(&info->lock,flags);
1446
1447         return 0;
1448 }
1449
1450 /**
1451  * called by network layer when interface enabled
1452  * claim resources and initialize hardware
1453  *
1454  * dev  pointer to network device structure
1455  *
1456  * returns 0 if success, otherwise error code
1457  */
1458 static int hdlcdev_open(struct net_device *dev)
1459 {
1460         struct slgt_info *info = dev_to_port(dev);
1461         int rc;
1462         unsigned long flags;
1463
1464         DBGINFO(("%s hdlcdev_open\n", dev->name));
1465
1466         /* generic HDLC layer open processing */
1467         if ((rc = hdlc_open(dev)))
1468                 return rc;
1469
1470         /* arbitrate between network and tty opens */
1471         spin_lock_irqsave(&info->netlock, flags);
1472         if (info->count != 0 || info->netcount != 0) {
1473                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1474                 spin_unlock_irqrestore(&info->netlock, flags);
1475                 return -EBUSY;
1476         }
1477         info->netcount=1;
1478         spin_unlock_irqrestore(&info->netlock, flags);
1479
1480         /* claim resources and init adapter */
1481         if ((rc = startup(info)) != 0) {
1482                 spin_lock_irqsave(&info->netlock, flags);
1483                 info->netcount=0;
1484                 spin_unlock_irqrestore(&info->netlock, flags);
1485                 return rc;
1486         }
1487
1488         /* assert DTR and RTS, apply hardware settings */
1489         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1490         program_hw(info);
1491
1492         /* enable network layer transmit */
1493         dev->trans_start = jiffies;
1494         netif_start_queue(dev);
1495
1496         /* inform generic HDLC layer of current DCD status */
1497         spin_lock_irqsave(&info->lock, flags);
1498         get_signals(info);
1499         spin_unlock_irqrestore(&info->lock, flags);
1500         hdlc_set_carrier(info->signals & SerialSignal_DCD, dev);
1501
1502         return 0;
1503 }
1504
1505 /**
1506  * called by network layer when interface is disabled
1507  * shutdown hardware and release resources
1508  *
1509  * dev  pointer to network device structure
1510  *
1511  * returns 0 if success, otherwise error code
1512  */
1513 static int hdlcdev_close(struct net_device *dev)
1514 {
1515         struct slgt_info *info = dev_to_port(dev);
1516         unsigned long flags;
1517
1518         DBGINFO(("%s hdlcdev_close\n", dev->name));
1519
1520         netif_stop_queue(dev);
1521
1522         /* shutdown adapter and release resources */
1523         shutdown(info);
1524
1525         hdlc_close(dev);
1526
1527         spin_lock_irqsave(&info->netlock, flags);
1528         info->netcount=0;
1529         spin_unlock_irqrestore(&info->netlock, flags);
1530
1531         return 0;
1532 }
1533
1534 /**
1535  * called by network layer to process IOCTL call to network device
1536  *
1537  * dev  pointer to network device structure
1538  * ifr  pointer to network interface request structure
1539  * cmd  IOCTL command code
1540  *
1541  * returns 0 if success, otherwise error code
1542  */
1543 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1544 {
1545         const size_t size = sizeof(sync_serial_settings);
1546         sync_serial_settings new_line;
1547         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1548         struct slgt_info *info = dev_to_port(dev);
1549         unsigned int flags;
1550
1551         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1552
1553         /* return error if TTY interface open */
1554         if (info->count)
1555                 return -EBUSY;
1556
1557         if (cmd != SIOCWANDEV)
1558                 return hdlc_ioctl(dev, ifr, cmd);
1559
1560         switch(ifr->ifr_settings.type) {
1561         case IF_GET_IFACE: /* return current sync_serial_settings */
1562
1563                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1564                 if (ifr->ifr_settings.size < size) {
1565                         ifr->ifr_settings.size = size; /* data size wanted */
1566                         return -ENOBUFS;
1567                 }
1568
1569                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1570                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1571                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1572                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1573
1574                 switch (flags){
1575                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1576                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1577                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1578                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1579                 default: new_line.clock_type = CLOCK_DEFAULT;
1580                 }
1581
1582                 new_line.clock_rate = info->params.clock_speed;
1583                 new_line.loopback   = info->params.loopback ? 1:0;
1584
1585                 if (copy_to_user(line, &new_line, size))
1586                         return -EFAULT;
1587                 return 0;
1588
1589         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1590
1591                 if(!capable(CAP_NET_ADMIN))
1592                         return -EPERM;
1593                 if (copy_from_user(&new_line, line, size))
1594                         return -EFAULT;
1595
1596                 switch (new_line.clock_type)
1597                 {
1598                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1599                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1600                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1601                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1602                 case CLOCK_DEFAULT:  flags = info->params.flags &
1603                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1604                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1605                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1606                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1607                 default: return -EINVAL;
1608                 }
1609
1610                 if (new_line.loopback != 0 && new_line.loopback != 1)
1611                         return -EINVAL;
1612
1613                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1614                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1615                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1616                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1617                 info->params.flags |= flags;
1618
1619                 info->params.loopback = new_line.loopback;
1620
1621                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1622                         info->params.clock_speed = new_line.clock_rate;
1623                 else
1624                         info->params.clock_speed = 0;
1625
1626                 /* if network interface up, reprogram hardware */
1627                 if (info->netcount)
1628                         program_hw(info);
1629                 return 0;
1630
1631         default:
1632                 return hdlc_ioctl(dev, ifr, cmd);
1633         }
1634 }
1635
1636 /**
1637  * called by network layer when transmit timeout is detected
1638  *
1639  * dev  pointer to network device structure
1640  */
1641 static void hdlcdev_tx_timeout(struct net_device *dev)
1642 {
1643         struct slgt_info *info = dev_to_port(dev);
1644         struct net_device_stats *stats = hdlc_stats(dev);
1645         unsigned long flags;
1646
1647         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1648
1649         stats->tx_errors++;
1650         stats->tx_aborted_errors++;
1651
1652         spin_lock_irqsave(&info->lock,flags);
1653         tx_stop(info);
1654         spin_unlock_irqrestore(&info->lock,flags);
1655
1656         netif_wake_queue(dev);
1657 }
1658
1659 /**
1660  * called by device driver when transmit completes
1661  * reenable network layer transmit if stopped
1662  *
1663  * info  pointer to device instance information
1664  */
1665 static void hdlcdev_tx_done(struct slgt_info *info)
1666 {
1667         if (netif_queue_stopped(info->netdev))
1668                 netif_wake_queue(info->netdev);
1669 }
1670
1671 /**
1672  * called by device driver when frame received
1673  * pass frame to network layer
1674  *
1675  * info  pointer to device instance information
1676  * buf   pointer to buffer contianing frame data
1677  * size  count of data bytes in buf
1678  */
1679 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1680 {
1681         struct sk_buff *skb = dev_alloc_skb(size);
1682         struct net_device *dev = info->netdev;
1683         struct net_device_stats *stats = hdlc_stats(dev);
1684
1685         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1686
1687         if (skb == NULL) {
1688                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1689                 stats->rx_dropped++;
1690                 return;
1691         }
1692
1693         memcpy(skb_put(skb, size),buf,size);
1694
1695         skb->protocol = hdlc_type_trans(skb, info->netdev);
1696
1697         stats->rx_packets++;
1698         stats->rx_bytes += size;
1699
1700         netif_rx(skb);
1701
1702         info->netdev->last_rx = jiffies;
1703 }
1704
1705 /**
1706  * called by device driver when adding device instance
1707  * do generic HDLC initialization
1708  *
1709  * info  pointer to device instance information
1710  *
1711  * returns 0 if success, otherwise error code
1712  */
1713 static int hdlcdev_init(struct slgt_info *info)
1714 {
1715         int rc;
1716         struct net_device *dev;
1717         hdlc_device *hdlc;
1718
1719         /* allocate and initialize network and HDLC layer objects */
1720
1721         if (!(dev = alloc_hdlcdev(info))) {
1722                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1723                 return -ENOMEM;
1724         }
1725
1726         /* for network layer reporting purposes only */
1727         dev->mem_start = info->phys_reg_addr;
1728         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1729         dev->irq       = info->irq_level;
1730
1731         /* network layer callbacks and settings */
1732         dev->do_ioctl       = hdlcdev_ioctl;
1733         dev->open           = hdlcdev_open;
1734         dev->stop           = hdlcdev_close;
1735         dev->tx_timeout     = hdlcdev_tx_timeout;
1736         dev->watchdog_timeo = 10*HZ;
1737         dev->tx_queue_len   = 50;
1738
1739         /* generic HDLC layer callbacks and settings */
1740         hdlc         = dev_to_hdlc(dev);
1741         hdlc->attach = hdlcdev_attach;
1742         hdlc->xmit   = hdlcdev_xmit;
1743
1744         /* register objects with HDLC layer */
1745         if ((rc = register_hdlc_device(dev))) {
1746                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1747                 free_netdev(dev);
1748                 return rc;
1749         }
1750
1751         info->netdev = dev;
1752         return 0;
1753 }
1754
1755 /**
1756  * called by device driver when removing device instance
1757  * do generic HDLC cleanup
1758  *
1759  * info  pointer to device instance information
1760  */
1761 static void hdlcdev_exit(struct slgt_info *info)
1762 {
1763         unregister_hdlc_device(info->netdev);
1764         free_netdev(info->netdev);
1765         info->netdev = NULL;
1766 }
1767
1768 #endif /* ifdef CONFIG_HDLC */
1769
1770 /*
1771  * get async data from rx DMA buffers
1772  */
1773 static void rx_async(struct slgt_info *info)
1774 {
1775         struct tty_struct *tty = info->tty;
1776         struct mgsl_icount *icount = &info->icount;
1777         unsigned int start, end;
1778         unsigned char *p;
1779         unsigned char status;
1780         struct slgt_desc *bufs = info->rbufs;
1781         int i, count;
1782         int chars = 0;
1783         int stat;
1784         unsigned char ch;
1785
1786         start = end = info->rbuf_current;
1787
1788         while(desc_complete(bufs[end])) {
1789                 count = desc_count(bufs[end]) - info->rbuf_index;
1790                 p     = bufs[end].buf + info->rbuf_index;
1791
1792                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1793                 DBGDATA(info, p, count, "rx");
1794
1795                 for(i=0 ; i < count; i+=2, p+=2) {
1796                         if (tty && chars) {
1797                                 tty_flip_buffer_push(tty);
1798                                 chars = 0;
1799                         }
1800                         ch = *p;
1801                         icount->rx++;
1802
1803                         stat = 0;
1804
1805                         if ((status = *(p+1) & (BIT9 + BIT8))) {
1806                                 if (status & BIT9)
1807                                         icount->parity++;
1808                                 else if (status & BIT8)
1809                                         icount->frame++;
1810                                 /* discard char if tty control flags say so */
1811                                 if (status & info->ignore_status_mask)
1812                                         continue;
1813                                 if (status & BIT9)
1814                                         stat = TTY_PARITY;
1815                                 else if (status & BIT8)
1816                                         stat = TTY_FRAME;
1817                         }
1818                         if (tty) {
1819                                 tty_insert_flip_char(tty, ch, stat);
1820                                 chars++;
1821                         }
1822                 }
1823
1824                 if (i < count) {
1825                         /* receive buffer not completed */
1826                         info->rbuf_index += i;
1827                         info->rx_timer.expires = jiffies + 1;
1828                         add_timer(&info->rx_timer);
1829                         break;
1830                 }
1831
1832                 info->rbuf_index = 0;
1833                 free_rbufs(info, end, end);
1834
1835                 if (++end == info->rbuf_count)
1836                         end = 0;
1837
1838                 /* if entire list searched then no frame available */
1839                 if (end == start)
1840                         break;
1841         }
1842
1843         if (tty && chars)
1844                 tty_flip_buffer_push(tty);
1845 }
1846
1847 /*
1848  * return next bottom half action to perform
1849  */
1850 static int bh_action(struct slgt_info *info)
1851 {
1852         unsigned long flags;
1853         int rc;
1854
1855         spin_lock_irqsave(&info->lock,flags);
1856
1857         if (info->pending_bh & BH_RECEIVE) {
1858                 info->pending_bh &= ~BH_RECEIVE;
1859                 rc = BH_RECEIVE;
1860         } else if (info->pending_bh & BH_TRANSMIT) {
1861                 info->pending_bh &= ~BH_TRANSMIT;
1862                 rc = BH_TRANSMIT;
1863         } else if (info->pending_bh & BH_STATUS) {
1864                 info->pending_bh &= ~BH_STATUS;
1865                 rc = BH_STATUS;
1866         } else {
1867                 /* Mark BH routine as complete */
1868                 info->bh_running   = 0;
1869                 info->bh_requested = 0;
1870                 rc = 0;
1871         }
1872
1873         spin_unlock_irqrestore(&info->lock,flags);
1874
1875         return rc;
1876 }
1877
1878 /*
1879  * perform bottom half processing
1880  */
1881 static void bh_handler(void* context)
1882 {
1883         struct slgt_info *info = context;
1884         int action;
1885
1886         if (!info)
1887                 return;
1888         info->bh_running = 1;
1889
1890         while((action = bh_action(info))) {
1891                 switch (action) {
1892                 case BH_RECEIVE:
1893                         DBGBH(("%s bh receive\n", info->device_name));
1894                         switch(info->params.mode) {
1895                         case MGSL_MODE_ASYNC:
1896                                 rx_async(info);
1897                                 break;
1898                         case MGSL_MODE_HDLC:
1899                                 while(rx_get_frame(info));
1900                                 break;
1901                         case MGSL_MODE_RAW:
1902                                 while(rx_get_buf(info));
1903                                 break;
1904                         }
1905                         /* restart receiver if rx DMA buffers exhausted */
1906                         if (info->rx_restart)
1907                                 rx_start(info);
1908                         break;
1909                 case BH_TRANSMIT:
1910                         bh_transmit(info);
1911                         break;
1912                 case BH_STATUS:
1913                         DBGBH(("%s bh status\n", info->device_name));
1914                         info->ri_chkcount = 0;
1915                         info->dsr_chkcount = 0;
1916                         info->dcd_chkcount = 0;
1917                         info->cts_chkcount = 0;
1918                         break;
1919                 default:
1920                         DBGBH(("%s unknown action\n", info->device_name));
1921                         break;
1922                 }
1923         }
1924         DBGBH(("%s bh_handler exit\n", info->device_name));
1925 }
1926
1927 static void bh_transmit(struct slgt_info *info)
1928 {
1929         struct tty_struct *tty = info->tty;
1930
1931         DBGBH(("%s bh_transmit\n", info->device_name));
1932         if (tty) {
1933                 tty_wakeup(tty);
1934                 wake_up_interruptible(&tty->write_wait);
1935         }
1936 }
1937
1938 static void dsr_change(struct slgt_info *info)
1939 {
1940         get_signals(info);
1941         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1942         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1943                 slgt_irq_off(info, IRQ_DSR);
1944                 return;
1945         }
1946         info->icount.dsr++;
1947         if (info->signals & SerialSignal_DSR)
1948                 info->input_signal_events.dsr_up++;
1949         else
1950                 info->input_signal_events.dsr_down++;
1951         wake_up_interruptible(&info->status_event_wait_q);
1952         wake_up_interruptible(&info->event_wait_q);
1953         info->pending_bh |= BH_STATUS;
1954 }
1955
1956 static void cts_change(struct slgt_info *info)
1957 {
1958         get_signals(info);
1959         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
1960         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1961                 slgt_irq_off(info, IRQ_CTS);
1962                 return;
1963         }
1964         info->icount.cts++;
1965         if (info->signals & SerialSignal_CTS)
1966                 info->input_signal_events.cts_up++;
1967         else
1968                 info->input_signal_events.cts_down++;
1969         wake_up_interruptible(&info->status_event_wait_q);
1970         wake_up_interruptible(&info->event_wait_q);
1971         info->pending_bh |= BH_STATUS;
1972
1973         if (info->flags & ASYNC_CTS_FLOW) {
1974                 if (info->tty) {
1975                         if (info->tty->hw_stopped) {
1976                                 if (info->signals & SerialSignal_CTS) {
1977                                         info->tty->hw_stopped = 0;
1978                                         info->pending_bh |= BH_TRANSMIT;
1979                                         return;
1980                                 }
1981                         } else {
1982                                 if (!(info->signals & SerialSignal_CTS))
1983                                         info->tty->hw_stopped = 1;
1984                         }
1985                 }
1986         }
1987 }
1988
1989 static void dcd_change(struct slgt_info *info)
1990 {
1991         get_signals(info);
1992         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
1993         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1994                 slgt_irq_off(info, IRQ_DCD);
1995                 return;
1996         }
1997         info->icount.dcd++;
1998         if (info->signals & SerialSignal_DCD) {
1999                 info->input_signal_events.dcd_up++;
2000         } else {
2001                 info->input_signal_events.dcd_down++;
2002         }
2003 #ifdef CONFIG_HDLC
2004         if (info->netcount)
2005                 hdlc_set_carrier(info->signals & SerialSignal_DCD, info->netdev);
2006 #endif
2007         wake_up_interruptible(&info->status_event_wait_q);
2008         wake_up_interruptible(&info->event_wait_q);
2009         info->pending_bh |= BH_STATUS;
2010
2011         if (info->flags & ASYNC_CHECK_CD) {
2012                 if (info->signals & SerialSignal_DCD)
2013                         wake_up_interruptible(&info->open_wait);
2014                 else {
2015                         if (info->tty)
2016                                 tty_hangup(info->tty);
2017                 }
2018         }
2019 }
2020
2021 static void ri_change(struct slgt_info *info)
2022 {
2023         get_signals(info);
2024         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2025         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2026                 slgt_irq_off(info, IRQ_RI);
2027                 return;
2028         }
2029         info->icount.dcd++;
2030         if (info->signals & SerialSignal_RI) {
2031                 info->input_signal_events.ri_up++;
2032         } else {
2033                 info->input_signal_events.ri_down++;
2034         }
2035         wake_up_interruptible(&info->status_event_wait_q);
2036         wake_up_interruptible(&info->event_wait_q);
2037         info->pending_bh |= BH_STATUS;
2038 }
2039
2040 static void isr_serial(struct slgt_info *info)
2041 {
2042         unsigned short status = rd_reg16(info, SSR);
2043
2044         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2045
2046         wr_reg16(info, SSR, status); /* clear pending */
2047
2048         info->irq_occurred = 1;
2049
2050         if (info->params.mode == MGSL_MODE_ASYNC) {
2051                 if (status & IRQ_TXIDLE) {
2052                         if (info->tx_count)
2053                                 isr_txeom(info, status);
2054                 }
2055                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2056                         info->icount.brk++;
2057                         /* process break detection if tty control allows */
2058                         if (info->tty) {
2059                                 if (!(status & info->ignore_status_mask)) {
2060                                         if (info->read_status_mask & MASK_BREAK) {
2061                                                 tty_insert_flip_char(info->tty, 0, TTY_BREAK);
2062                                                 if (info->flags & ASYNC_SAK)
2063                                                         do_SAK(info->tty);
2064                                         }
2065                                 }
2066                         }
2067                 }
2068         } else {
2069                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2070                         isr_txeom(info, status);
2071
2072                 if (status & IRQ_RXIDLE) {
2073                         if (status & RXIDLE)
2074                                 info->icount.rxidle++;
2075                         else
2076                                 info->icount.exithunt++;
2077                         wake_up_interruptible(&info->event_wait_q);
2078                 }
2079
2080                 if (status & IRQ_RXOVER)
2081                         rx_start(info);
2082         }
2083
2084         if (status & IRQ_DSR)
2085                 dsr_change(info);
2086         if (status & IRQ_CTS)
2087                 cts_change(info);
2088         if (status & IRQ_DCD)
2089                 dcd_change(info);
2090         if (status & IRQ_RI)
2091                 ri_change(info);
2092 }
2093
2094 static void isr_rdma(struct slgt_info *info)
2095 {
2096         unsigned int status = rd_reg32(info, RDCSR);
2097
2098         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2099
2100         /* RDCSR (rx DMA control/status)
2101          *
2102          * 31..07  reserved
2103          * 06      save status byte to DMA buffer
2104          * 05      error
2105          * 04      eol (end of list)
2106          * 03      eob (end of buffer)
2107          * 02      IRQ enable
2108          * 01      reset
2109          * 00      enable
2110          */
2111         wr_reg32(info, RDCSR, status);  /* clear pending */
2112
2113         if (status & (BIT5 + BIT4)) {
2114                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2115                 info->rx_restart = 1;
2116         }
2117         info->pending_bh |= BH_RECEIVE;
2118 }
2119
2120 static void isr_tdma(struct slgt_info *info)
2121 {
2122         unsigned int status = rd_reg32(info, TDCSR);
2123
2124         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2125
2126         /* TDCSR (tx DMA control/status)
2127          *
2128          * 31..06  reserved
2129          * 05      error
2130          * 04      eol (end of list)
2131          * 03      eob (end of buffer)
2132          * 02      IRQ enable
2133          * 01      reset
2134          * 00      enable
2135          */
2136         wr_reg32(info, TDCSR, status);  /* clear pending */
2137
2138         if (status & (BIT5 + BIT4 + BIT3)) {
2139                 // another transmit buffer has completed
2140                 // run bottom half to get more send data from user
2141                 info->pending_bh |= BH_TRANSMIT;
2142         }
2143 }
2144
2145 static void isr_txeom(struct slgt_info *info, unsigned short status)
2146 {
2147         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2148
2149         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2150         tdma_reset(info);
2151         reset_tbufs(info);
2152         if (status & IRQ_TXUNDER) {
2153                 unsigned short val = rd_reg16(info, TCR);
2154                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2155                 wr_reg16(info, TCR, val); /* clear reset bit */
2156         }
2157
2158         if (info->tx_active) {
2159                 if (info->params.mode != MGSL_MODE_ASYNC) {
2160                         if (status & IRQ_TXUNDER)
2161                                 info->icount.txunder++;
2162                         else if (status & IRQ_TXIDLE)
2163                                 info->icount.txok++;
2164                 }
2165
2166                 info->tx_active = 0;
2167                 info->tx_count = 0;
2168
2169                 del_timer(&info->tx_timer);
2170
2171                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2172                         info->signals &= ~SerialSignal_RTS;
2173                         info->drop_rts_on_tx_done = 0;
2174                         set_signals(info);
2175                 }
2176
2177 #ifdef CONFIG_HDLC
2178                 if (info->netcount)
2179                         hdlcdev_tx_done(info);
2180                 else
2181 #endif
2182                 {
2183                         if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
2184                                 tx_stop(info);
2185                                 return;
2186                         }
2187                         info->pending_bh |= BH_TRANSMIT;
2188                 }
2189         }
2190 }
2191
2192 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2193 {
2194         struct cond_wait *w, *prev;
2195
2196         /* wake processes waiting for specific transitions */
2197         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2198                 if (w->data & changed) {
2199                         w->data = state;
2200                         wake_up_interruptible(&w->q);
2201                         if (prev != NULL)
2202                                 prev->next = w->next;
2203                         else
2204                                 info->gpio_wait_q = w->next;
2205                 } else
2206                         prev = w;
2207         }
2208 }
2209
2210 /* interrupt service routine
2211  *
2212  *      irq     interrupt number
2213  *      dev_id  device ID supplied during interrupt registration
2214  *      regs    interrupted processor context
2215  */
2216 static irqreturn_t slgt_interrupt(int irq, void *dev_id, struct pt_regs * regs)
2217 {
2218         struct slgt_info *info;
2219         unsigned int gsr;
2220         unsigned int i;
2221
2222         DBGISR(("slgt_interrupt irq=%d entry\n", irq));
2223
2224         info = dev_id;
2225         if (!info)
2226                 return IRQ_NONE;
2227
2228         spin_lock(&info->lock);
2229
2230         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2231                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2232                 info->irq_occurred = 1;
2233                 for(i=0; i < info->port_count ; i++) {
2234                         if (info->port_array[i] == NULL)
2235                                 continue;
2236                         if (gsr & (BIT8 << i))
2237                                 isr_serial(info->port_array[i]);
2238                         if (gsr & (BIT16 << (i*2)))
2239                                 isr_rdma(info->port_array[i]);
2240                         if (gsr & (BIT17 << (i*2)))
2241                                 isr_tdma(info->port_array[i]);
2242                 }
2243         }
2244
2245         if (info->gpio_present) {
2246                 unsigned int state;
2247                 unsigned int changed;
2248                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2249                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2250                         /* read latched state of GPIO signals */
2251                         state = rd_reg32(info, IOVR);
2252                         /* clear pending GPIO interrupt bits */
2253                         wr_reg32(info, IOSR, changed);
2254                         for (i=0 ; i < info->port_count ; i++) {
2255                                 if (info->port_array[i] != NULL)
2256                                         isr_gpio(info->port_array[i], changed, state);
2257                         }
2258                 }
2259         }
2260
2261         for(i=0; i < info->port_count ; i++) {
2262                 struct slgt_info *port = info->port_array[i];
2263
2264                 if (port && (port->count || port->netcount) &&
2265                     port->pending_bh && !port->bh_running &&
2266                     !port->bh_requested) {
2267                         DBGISR(("%s bh queued\n", port->device_name));
2268                         schedule_work(&port->task);
2269                         port->bh_requested = 1;
2270                 }
2271         }
2272
2273         spin_unlock(&info->lock);
2274
2275         DBGISR(("slgt_interrupt irq=%d exit\n", irq));
2276         return IRQ_HANDLED;
2277 }
2278
2279 static int startup(struct slgt_info *info)
2280 {
2281         DBGINFO(("%s startup\n", info->device_name));
2282
2283         if (info->flags & ASYNC_INITIALIZED)
2284                 return 0;
2285
2286         if (!info->tx_buf) {
2287                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2288                 if (!info->tx_buf) {
2289                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2290                         return -ENOMEM;
2291                 }
2292         }
2293
2294         info->pending_bh = 0;
2295
2296         memset(&info->icount, 0, sizeof(info->icount));
2297
2298         /* program hardware for current parameters */
2299         change_params(info);
2300
2301         if (info->tty)
2302                 clear_bit(TTY_IO_ERROR, &info->tty->flags);
2303
2304         info->flags |= ASYNC_INITIALIZED;
2305
2306         return 0;
2307 }
2308
2309 /*
2310  *  called by close() and hangup() to shutdown hardware
2311  */
2312 static void shutdown(struct slgt_info *info)
2313 {
2314         unsigned long flags;
2315
2316         if (!(info->flags & ASYNC_INITIALIZED))
2317                 return;
2318
2319         DBGINFO(("%s shutdown\n", info->device_name));
2320
2321         /* clear status wait queue because status changes */
2322         /* can't happen after shutting down the hardware */
2323         wake_up_interruptible(&info->status_event_wait_q);
2324         wake_up_interruptible(&info->event_wait_q);
2325
2326         del_timer_sync(&info->tx_timer);
2327         del_timer_sync(&info->rx_timer);
2328
2329         kfree(info->tx_buf);
2330         info->tx_buf = NULL;
2331
2332         spin_lock_irqsave(&info->lock,flags);
2333
2334         tx_stop(info);
2335         rx_stop(info);
2336
2337         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2338
2339         if (!info->tty || info->tty->termios->c_cflag & HUPCL) {
2340                 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2341                 set_signals(info);
2342         }
2343
2344         flush_cond_wait(&info->gpio_wait_q);
2345
2346         spin_unlock_irqrestore(&info->lock,flags);
2347
2348         if (info->tty)
2349                 set_bit(TTY_IO_ERROR, &info->tty->flags);
2350
2351         info->flags &= ~ASYNC_INITIALIZED;
2352 }
2353
2354 static void program_hw(struct slgt_info *info)
2355 {
2356         unsigned long flags;
2357
2358         spin_lock_irqsave(&info->lock,flags);
2359
2360         rx_stop(info);
2361         tx_stop(info);
2362
2363         if (info->params.mode == MGSL_MODE_HDLC ||
2364             info->params.mode == MGSL_MODE_RAW ||
2365             info->netcount)
2366                 hdlc_mode(info);
2367         else
2368                 async_mode(info);
2369
2370         set_signals(info);
2371
2372         info->dcd_chkcount = 0;
2373         info->cts_chkcount = 0;
2374         info->ri_chkcount = 0;
2375         info->dsr_chkcount = 0;
2376
2377         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
2378         get_signals(info);
2379
2380         if (info->netcount ||
2381             (info->tty && info->tty->termios->c_cflag & CREAD))
2382                 rx_start(info);
2383
2384         spin_unlock_irqrestore(&info->lock,flags);
2385 }
2386
2387 /*
2388  * reconfigure adapter based on new parameters
2389  */
2390 static void change_params(struct slgt_info *info)
2391 {
2392         unsigned cflag;
2393         int bits_per_char;
2394
2395         if (!info->tty || !info->tty->termios)
2396                 return;
2397         DBGINFO(("%s change_params\n", info->device_name));
2398
2399         cflag = info->tty->termios->c_cflag;
2400
2401         /* if B0 rate (hangup) specified then negate DTR and RTS */
2402         /* otherwise assert DTR and RTS */
2403         if (cflag & CBAUD)
2404                 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2405         else
2406                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2407
2408         /* byte size and parity */
2409
2410         switch (cflag & CSIZE) {
2411         case CS5: info->params.data_bits = 5; break;
2412         case CS6: info->params.data_bits = 6; break;
2413         case CS7: info->params.data_bits = 7; break;
2414         case CS8: info->params.data_bits = 8; break;
2415         default:  info->params.data_bits = 7; break;
2416         }
2417
2418         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2419
2420         if (cflag & PARENB)
2421                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2422         else
2423                 info->params.parity = ASYNC_PARITY_NONE;
2424
2425         /* calculate number of jiffies to transmit a full
2426          * FIFO (32 bytes) at specified data rate
2427          */
2428         bits_per_char = info->params.data_bits +
2429                         info->params.stop_bits + 1;
2430
2431         info->params.data_rate = tty_get_baud_rate(info->tty);
2432
2433         if (info->params.data_rate) {
2434                 info->timeout = (32*HZ*bits_per_char) /
2435                                 info->params.data_rate;
2436         }
2437         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2438
2439         if (cflag & CRTSCTS)
2440                 info->flags |= ASYNC_CTS_FLOW;
2441         else
2442                 info->flags &= ~ASYNC_CTS_FLOW;
2443
2444         if (cflag & CLOCAL)
2445                 info->flags &= ~ASYNC_CHECK_CD;
2446         else
2447                 info->flags |= ASYNC_CHECK_CD;
2448
2449         /* process tty input control flags */
2450
2451         info->read_status_mask = IRQ_RXOVER;
2452         if (I_INPCK(info->tty))
2453                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2454         if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
2455                 info->read_status_mask |= MASK_BREAK;
2456         if (I_IGNPAR(info->tty))
2457                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2458         if (I_IGNBRK(info->tty)) {
2459                 info->ignore_status_mask |= MASK_BREAK;
2460                 /* If ignoring parity and break indicators, ignore
2461                  * overruns too.  (For real raw support).
2462                  */
2463                 if (I_IGNPAR(info->tty))
2464                         info->ignore_status_mask |= MASK_OVERRUN;
2465         }
2466
2467         program_hw(info);
2468 }
2469
2470 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2471 {
2472         DBGINFO(("%s get_stats\n",  info->device_name));
2473         if (!user_icount) {
2474                 memset(&info->icount, 0, sizeof(info->icount));
2475         } else {
2476                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2477                         return -EFAULT;
2478         }
2479         return 0;
2480 }
2481
2482 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2483 {
2484         DBGINFO(("%s get_params\n", info->device_name));
2485         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2486                 return -EFAULT;
2487         return 0;
2488 }
2489
2490 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2491 {
2492         unsigned long flags;
2493         MGSL_PARAMS tmp_params;
2494
2495         DBGINFO(("%s set_params\n", info->device_name));
2496         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2497                 return -EFAULT;
2498
2499         spin_lock_irqsave(&info->lock, flags);
2500         memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2501         spin_unlock_irqrestore(&info->lock, flags);
2502
2503         change_params(info);
2504
2505         return 0;
2506 }
2507
2508 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2509 {
2510         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2511         if (put_user(info->idle_mode, idle_mode))
2512                 return -EFAULT;
2513         return 0;
2514 }
2515
2516 static int set_txidle(struct slgt_info *info, int idle_mode)
2517 {
2518         unsigned long flags;
2519         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2520         spin_lock_irqsave(&info->lock,flags);
2521         info->idle_mode = idle_mode;
2522         tx_set_idle(info);
2523         spin_unlock_irqrestore(&info->lock,flags);
2524         return 0;
2525 }
2526
2527 static int tx_enable(struct slgt_info *info, int enable)
2528 {
2529         unsigned long flags;
2530         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2531         spin_lock_irqsave(&info->lock,flags);
2532         if (enable) {
2533                 if (!info->tx_enabled)
2534                         tx_start(info);
2535         } else {
2536                 if (info->tx_enabled)
2537                         tx_stop(info);
2538         }
2539         spin_unlock_irqrestore(&info->lock,flags);
2540         return 0;
2541 }
2542
2543 /*
2544  * abort transmit HDLC frame
2545  */
2546 static int tx_abort(struct slgt_info *info)
2547 {
2548         unsigned long flags;
2549         DBGINFO(("%s tx_abort\n", info->device_name));
2550         spin_lock_irqsave(&info->lock,flags);
2551         tdma_reset(info);
2552         spin_unlock_irqrestore(&info->lock,flags);
2553         return 0;
2554 }
2555
2556 static int rx_enable(struct slgt_info *info, int enable)
2557 {
2558         unsigned long flags;
2559         DBGINFO(("%s rx_enable(%d)\n", info->device_name, enable));
2560         spin_lock_irqsave(&info->lock,flags);
2561         if (enable) {
2562                 if (!info->rx_enabled)
2563                         rx_start(info);
2564         } else {
2565                 if (info->rx_enabled)
2566                         rx_stop(info);
2567         }
2568         spin_unlock_irqrestore(&info->lock,flags);
2569         return 0;
2570 }
2571
2572 /*
2573  *  wait for specified event to occur
2574  */
2575 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2576 {
2577         unsigned long flags;
2578         int s;
2579         int rc=0;
2580         struct mgsl_icount cprev, cnow;
2581         int events;
2582         int mask;
2583         struct  _input_signal_events oldsigs, newsigs;
2584         DECLARE_WAITQUEUE(wait, current);
2585
2586         if (get_user(mask, mask_ptr))
2587                 return -EFAULT;
2588
2589         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2590
2591         spin_lock_irqsave(&info->lock,flags);
2592
2593         /* return immediately if state matches requested events */
2594         get_signals(info);
2595         s = info->signals;
2596
2597         events = mask &
2598                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2599                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2600                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2601                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2602         if (events) {
2603                 spin_unlock_irqrestore(&info->lock,flags);
2604                 goto exit;
2605         }
2606
2607         /* save current irq counts */
2608         cprev = info->icount;
2609         oldsigs = info->input_signal_events;
2610
2611         /* enable hunt and idle irqs if needed */
2612         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2613                 unsigned short val = rd_reg16(info, SCR);
2614                 if (!(val & IRQ_RXIDLE))
2615                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2616         }
2617
2618         set_current_state(TASK_INTERRUPTIBLE);
2619         add_wait_queue(&info->event_wait_q, &wait);
2620
2621         spin_unlock_irqrestore(&info->lock,flags);
2622
2623         for(;;) {
2624                 schedule();
2625                 if (signal_pending(current)) {
2626                         rc = -ERESTARTSYS;
2627                         break;
2628                 }
2629
2630                 /* get current irq counts */
2631                 spin_lock_irqsave(&info->lock,flags);
2632                 cnow = info->icount;
2633                 newsigs = info->input_signal_events;
2634                 set_current_state(TASK_INTERRUPTIBLE);
2635                 spin_unlock_irqrestore(&info->lock,flags);
2636
2637                 /* if no change, wait aborted for some reason */
2638                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2639                     newsigs.dsr_down == oldsigs.dsr_down &&
2640                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2641                     newsigs.dcd_down == oldsigs.dcd_down &&
2642                     newsigs.cts_up   == oldsigs.cts_up   &&
2643                     newsigs.cts_down == oldsigs.cts_down &&
2644                     newsigs.ri_up    == oldsigs.ri_up    &&
2645                     newsigs.ri_down  == oldsigs.ri_down  &&
2646                     cnow.exithunt    == cprev.exithunt   &&
2647                     cnow.rxidle      == cprev.rxidle) {
2648                         rc = -EIO;
2649                         break;
2650                 }
2651
2652                 events = mask &
2653                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2654                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2655                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2656                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2657                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2658                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2659                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2660                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2661                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2662                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2663                 if (events)
2664                         break;
2665
2666                 cprev = cnow;
2667                 oldsigs = newsigs;
2668         }
2669
2670         remove_wait_queue(&info->event_wait_q, &wait);
2671         set_current_state(TASK_RUNNING);
2672
2673
2674         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2675                 spin_lock_irqsave(&info->lock,flags);
2676                 if (!waitqueue_active(&info->event_wait_q)) {
2677                         /* disable enable exit hunt mode/idle rcvd IRQs */
2678                         wr_reg16(info, SCR,
2679                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2680                 }
2681                 spin_unlock_irqrestore(&info->lock,flags);
2682         }
2683 exit:
2684         if (rc == 0)
2685                 rc = put_user(events, mask_ptr);
2686         return rc;
2687 }
2688
2689 static int get_interface(struct slgt_info *info, int __user *if_mode)
2690 {
2691         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2692         if (put_user(info->if_mode, if_mode))
2693                 return -EFAULT;
2694         return 0;
2695 }
2696
2697 static int set_interface(struct slgt_info *info, int if_mode)
2698 {
2699         unsigned long flags;
2700         unsigned short val;
2701
2702         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2703         spin_lock_irqsave(&info->lock,flags);
2704         info->if_mode = if_mode;
2705
2706         msc_set_vcr(info);
2707
2708         /* TCR (tx control) 07  1=RTS driver control */
2709         val = rd_reg16(info, TCR);
2710         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2711                 val |= BIT7;
2712         else
2713                 val &= ~BIT7;
2714         wr_reg16(info, TCR, val);
2715
2716         spin_unlock_irqrestore(&info->lock,flags);
2717         return 0;
2718 }
2719
2720 /*
2721  * set general purpose IO pin state and direction
2722  *
2723  * user_gpio fields:
2724  * state   each bit indicates a pin state
2725  * smask   set bit indicates pin state to set
2726  * dir     each bit indicates a pin direction (0=input, 1=output)
2727  * dmask   set bit indicates pin direction to set
2728  */
2729 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2730 {
2731         unsigned long flags;
2732         struct gpio_desc gpio;
2733         __u32 data;
2734
2735         if (!info->gpio_present)
2736                 return -EINVAL;
2737         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2738                 return -EFAULT;
2739         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2740                  info->device_name, gpio.state, gpio.smask,
2741                  gpio.dir, gpio.dmask));
2742
2743         spin_lock_irqsave(&info->lock,flags);
2744         if (gpio.dmask) {
2745                 data = rd_reg32(info, IODR);
2746                 data |= gpio.dmask & gpio.dir;
2747                 data &= ~(gpio.dmask & ~gpio.dir);
2748                 wr_reg32(info, IODR, data);
2749         }
2750         if (gpio.smask) {
2751                 data = rd_reg32(info, IOVR);
2752                 data |= gpio.smask & gpio.state;
2753                 data &= ~(gpio.smask & ~gpio.state);
2754                 wr_reg32(info, IOVR, data);
2755         }
2756         spin_unlock_irqrestore(&info->lock,flags);
2757
2758         return 0;
2759 }
2760
2761 /*
2762  * get general purpose IO pin state and direction
2763  */
2764 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2765 {
2766         struct gpio_desc gpio;
2767         if (!info->gpio_present)
2768                 return -EINVAL;
2769         gpio.state = rd_reg32(info, IOVR);
2770         gpio.smask = 0xffffffff;
2771         gpio.dir   = rd_reg32(info, IODR);
2772         gpio.dmask = 0xffffffff;
2773         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2774                 return -EFAULT;
2775         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2776                  info->device_name, gpio.state, gpio.dir));
2777         return 0;
2778 }
2779
2780 /*
2781  * conditional wait facility
2782  */
2783 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2784 {
2785         init_waitqueue_head(&w->q);
2786         init_waitqueue_entry(&w->wait, current);
2787         w->data = data;
2788 }
2789
2790 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2791 {
2792         set_current_state(TASK_INTERRUPTIBLE);
2793         add_wait_queue(&w->q, &w->wait);
2794         w->next = *head;
2795         *head = w;
2796 }
2797
2798 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2799 {
2800         struct cond_wait *w, *prev;
2801         remove_wait_queue(&cw->q, &cw->wait);
2802         set_current_state(TASK_RUNNING);
2803         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2804                 if (w == cw) {
2805                         if (prev != NULL)
2806                                 prev->next = w->next;
2807                         else
2808                                 *head = w->next;
2809                         break;
2810                 }
2811         }
2812 }
2813
2814 static void flush_cond_wait(struct cond_wait **head)
2815 {
2816         while (*head != NULL) {
2817                 wake_up_interruptible(&(*head)->q);
2818                 *head = (*head)->next;
2819         }
2820 }
2821
2822 /*
2823  * wait for general purpose I/O pin(s) to enter specified state
2824  *
2825  * user_gpio fields:
2826  * state - bit indicates target pin state
2827  * smask - set bit indicates watched pin
2828  *
2829  * The wait ends when at least one watched pin enters the specified
2830  * state. When 0 (no error) is returned, user_gpio->state is set to the
2831  * state of all GPIO pins when the wait ends.
2832  *
2833  * Note: Each pin may be a dedicated input, dedicated output, or
2834  * configurable input/output. The number and configuration of pins
2835  * varies with the specific adapter model. Only input pins (dedicated
2836  * or configured) can be monitored with this function.
2837  */
2838 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2839 {
2840         unsigned long flags;
2841         int rc = 0;
2842         struct gpio_desc gpio;
2843         struct cond_wait wait;
2844         u32 state;
2845
2846         if (!info->gpio_present)
2847                 return -EINVAL;
2848         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2849                 return -EFAULT;
2850         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2851                  info->device_name, gpio.state, gpio.smask));
2852         /* ignore output pins identified by set IODR bit */
2853         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2854                 return -EINVAL;
2855         init_cond_wait(&wait, gpio.smask);
2856
2857         spin_lock_irqsave(&info->lock, flags);
2858         /* enable interrupts for watched pins */
2859         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
2860         /* get current pin states */
2861         state = rd_reg32(info, IOVR);
2862
2863         if (gpio.smask & ~(state ^ gpio.state)) {
2864                 /* already in target state */
2865                 gpio.state = state;
2866         } else {
2867                 /* wait for target state */
2868                 add_cond_wait(&info->gpio_wait_q, &wait);
2869                 spin_unlock_irqrestore(&info->lock, flags);
2870                 schedule();
2871                 if (signal_pending(current))
2872                         rc = -ERESTARTSYS;
2873                 else
2874                         gpio.state = wait.data;
2875                 spin_lock_irqsave(&info->lock, flags);
2876                 remove_cond_wait(&info->gpio_wait_q, &wait);
2877         }
2878
2879         /* disable all GPIO interrupts if no waiting processes */
2880         if (info->gpio_wait_q == NULL)
2881                 wr_reg32(info, IOER, 0);
2882         spin_unlock_irqrestore(&info->lock,flags);
2883
2884         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2885                 rc = -EFAULT;
2886         return rc;
2887 }
2888
2889 static int modem_input_wait(struct slgt_info *info,int arg)
2890 {
2891         unsigned long flags;
2892         int rc;
2893         struct mgsl_icount cprev, cnow;
2894         DECLARE_WAITQUEUE(wait, current);
2895
2896         /* save current irq counts */
2897         spin_lock_irqsave(&info->lock,flags);
2898         cprev = info->icount;
2899         add_wait_queue(&info->status_event_wait_q, &wait);
2900         set_current_state(TASK_INTERRUPTIBLE);
2901         spin_unlock_irqrestore(&info->lock,flags);
2902
2903         for(;;) {
2904                 schedule();
2905                 if (signal_pending(current)) {
2906                         rc = -ERESTARTSYS;
2907                         break;
2908                 }
2909
2910                 /* get new irq counts */
2911                 spin_lock_irqsave(&info->lock,flags);
2912                 cnow = info->icount;
2913                 set_current_state(TASK_INTERRUPTIBLE);
2914                 spin_unlock_irqrestore(&info->lock,flags);
2915
2916                 /* if no change, wait aborted for some reason */
2917                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
2918                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
2919                         rc = -EIO;
2920                         break;
2921                 }
2922
2923                 /* check for change in caller specified modem input */
2924                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
2925                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
2926                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
2927                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
2928                         rc = 0;
2929                         break;
2930                 }
2931
2932                 cprev = cnow;
2933         }
2934         remove_wait_queue(&info->status_event_wait_q, &wait);
2935         set_current_state(TASK_RUNNING);
2936         return rc;
2937 }
2938
2939 /*
2940  *  return state of serial control and status signals
2941  */
2942 static int tiocmget(struct tty_struct *tty, struct file *file)
2943 {
2944         struct slgt_info *info = tty->driver_data;
2945         unsigned int result;
2946         unsigned long flags;
2947
2948         spin_lock_irqsave(&info->lock,flags);
2949         get_signals(info);
2950         spin_unlock_irqrestore(&info->lock,flags);
2951
2952         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
2953                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
2954                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
2955                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
2956                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
2957                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
2958
2959         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
2960         return result;
2961 }
2962
2963 /*
2964  * set modem control signals (DTR/RTS)
2965  *
2966  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
2967  *              TIOCMSET = set/clear signal values
2968  *      value   bit mask for command
2969  */
2970 static int tiocmset(struct tty_struct *tty, struct file *file,
2971                     unsigned int set, unsigned int clear)
2972 {
2973         struct slgt_info *info = tty->driver_data;
2974         unsigned long flags;
2975
2976         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
2977
2978         if (set & TIOCM_RTS)
2979                 info->signals |= SerialSignal_RTS;
2980         if (set & TIOCM_DTR)
2981                 info->signals |= SerialSignal_DTR;
2982         if (clear & TIOCM_RTS)
2983                 info->signals &= ~SerialSignal_RTS;
2984         if (clear & TIOCM_DTR)
2985                 info->signals &= ~SerialSignal_DTR;
2986
2987         spin_lock_irqsave(&info->lock,flags);
2988         set_signals(info);
2989         spin_unlock_irqrestore(&info->lock,flags);
2990         return 0;
2991 }
2992
2993 /*
2994  *  block current process until the device is ready to open
2995  */
2996 static int block_til_ready(struct tty_struct *tty, struct file *filp,
2997                            struct slgt_info *info)
2998 {
2999         DECLARE_WAITQUEUE(wait, current);
3000         int             retval;
3001         int             do_clocal = 0, extra_count = 0;
3002         unsigned long   flags;
3003
3004         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3005
3006         if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3007                 /* nonblock mode is set or port is not enabled */
3008                 info->flags |= ASYNC_NORMAL_ACTIVE;
3009                 return 0;
3010         }
3011
3012         if (tty->termios->c_cflag & CLOCAL)
3013                 do_clocal = 1;
3014
3015         /* Wait for carrier detect and the line to become
3016          * free (i.e., not in use by the callout).  While we are in
3017          * this loop, info->count is dropped by one, so that
3018          * close() knows when to free things.  We restore it upon
3019          * exit, either normal or abnormal.
3020          */
3021
3022         retval = 0;
3023         add_wait_queue(&info->open_wait, &wait);
3024
3025         spin_lock_irqsave(&info->lock, flags);
3026         if (!tty_hung_up_p(filp)) {
3027                 extra_count = 1;
3028                 info->count--;
3029         }
3030         spin_unlock_irqrestore(&info->lock, flags);
3031         info->blocked_open++;
3032
3033         while (1) {
3034                 if ((tty->termios->c_cflag & CBAUD)) {
3035                         spin_lock_irqsave(&info->lock,flags);
3036                         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3037                         set_signals(info);
3038                         spin_unlock_irqrestore(&info->lock,flags);
3039                 }
3040
3041                 set_current_state(TASK_INTERRUPTIBLE);
3042
3043                 if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){
3044                         retval = (info->flags & ASYNC_HUP_NOTIFY) ?
3045                                         -EAGAIN : -ERESTARTSYS;
3046                         break;
3047                 }
3048
3049                 spin_lock_irqsave(&info->lock,flags);
3050                 get_signals(info);
3051                 spin_unlock_irqrestore(&info->lock,flags);
3052
3053                 if (!(info->flags & ASYNC_CLOSING) &&
3054                     (do_clocal || (info->signals & SerialSignal_DCD)) ) {
3055                         break;
3056                 }
3057
3058                 if (signal_pending(current)) {
3059                         retval = -ERESTARTSYS;
3060                         break;
3061                 }
3062
3063                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3064                 schedule();
3065         }
3066
3067         set_current_state(TASK_RUNNING);
3068         remove_wait_queue(&info->open_wait, &wait);
3069
3070         if (extra_count)
3071                 info->count++;
3072         info->blocked_open--;
3073
3074         if (!retval)
3075                 info->flags |= ASYNC_NORMAL_ACTIVE;
3076
3077         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3078         return retval;
3079 }
3080
3081 static int alloc_tmp_rbuf(struct slgt_info *info)
3082 {
3083         info->tmp_rbuf = kmalloc(info->max_frame_size, GFP_KERNEL);
3084         if (info->tmp_rbuf == NULL)
3085                 return -ENOMEM;
3086         return 0;
3087 }
3088
3089 static void free_tmp_rbuf(struct slgt_info *info)
3090 {
3091         kfree(info->tmp_rbuf);
3092         info->tmp_rbuf = NULL;
3093 }
3094
3095 /*
3096  * allocate DMA descriptor lists.
3097  */
3098 static int alloc_desc(struct slgt_info *info)
3099 {
3100         unsigned int i;
3101         unsigned int pbufs;
3102
3103         /* allocate memory to hold descriptor lists */
3104         info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3105         if (info->bufs == NULL)
3106                 return -ENOMEM;
3107
3108         memset(info->bufs, 0, DESC_LIST_SIZE);
3109
3110         info->rbufs = (struct slgt_desc*)info->bufs;
3111         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3112
3113         pbufs = (unsigned int)info->bufs_dma_addr;
3114
3115         /*
3116          * Build circular lists of descriptors
3117          */
3118
3119         for (i=0; i < info->rbuf_count; i++) {
3120                 /* physical address of this descriptor */
3121                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3122
3123                 /* physical address of next descriptor */
3124                 if (i == info->rbuf_count - 1)
3125                         info->rbufs[i].next = cpu_to_le32(pbufs);
3126                 else
3127                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3128                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3129         }
3130
3131         for (i=0; i < info->tbuf_count; i++) {
3132                 /* physical address of this descriptor */
3133                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3134
3135                 /* physical address of next descriptor */
3136                 if (i == info->tbuf_count - 1)
3137                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3138                 else
3139                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3140         }
3141
3142         return 0;
3143 }
3144
3145 static void free_desc(struct slgt_info *info)
3146 {
3147         if (info->bufs != NULL) {
3148                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3149                 info->bufs  = NULL;
3150                 info->rbufs = NULL;
3151                 info->tbufs = NULL;
3152         }
3153 }
3154
3155 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3156 {
3157         int i;
3158         for (i=0; i < count; i++) {
3159                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3160                         return -ENOMEM;
3161                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3162         }
3163         return 0;
3164 }
3165
3166 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3167 {
3168         int i;
3169         for (i=0; i < count; i++) {
3170                 if (bufs[i].buf == NULL)
3171                         continue;
3172                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3173                 bufs[i].buf = NULL;
3174         }
3175 }
3176
3177 static int alloc_dma_bufs(struct slgt_info *info)
3178 {
3179         info->rbuf_count = 32;
3180         info->tbuf_count = 32;
3181
3182         if (alloc_desc(info) < 0 ||
3183             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3184             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3185             alloc_tmp_rbuf(info) < 0) {
3186                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3187                 return -ENOMEM;
3188         }
3189         reset_rbufs(info);
3190         return 0;
3191 }
3192
3193 static void free_dma_bufs(struct slgt_info *info)
3194 {
3195         if (info->bufs) {
3196                 free_bufs(info, info->rbufs, info->rbuf_count);
3197                 free_bufs(info, info->tbufs, info->tbuf_count);
3198                 free_desc(info);
3199         }
3200         free_tmp_rbuf(info);
3201 }
3202
3203 static int claim_resources(struct slgt_info *info)
3204 {
3205         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3206                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3207                         info->device_name, info->phys_reg_addr));
3208                 info->init_error = DiagStatus_AddressConflict;
3209                 goto errout;
3210         }
3211         else
3212                 info->reg_addr_requested = 1;
3213
3214         info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
3215         if (!info->reg_addr) {
3216                 DBGERR(("%s cant map device registers, addr=%08X\n",
3217                         info->device_name, info->phys_reg_addr));
3218                 info->init_error = DiagStatus_CantAssignPciResources;
3219                 goto errout;
3220         }
3221         return 0;
3222
3223 errout:
3224         release_resources(info);
3225         return -ENODEV;
3226 }
3227
3228 static void release_resources(struct slgt_info *info)
3229 {
3230         if (info->irq_requested) {
3231                 free_irq(info->irq_level, info);
3232                 info->irq_requested = 0;
3233         }
3234
3235         if (info->reg_addr_requested) {
3236                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3237                 info->reg_addr_requested = 0;
3238         }
3239
3240         if (info->reg_addr) {
3241                 iounmap(info->reg_addr);
3242                 info->reg_addr = NULL;
3243         }
3244 }
3245
3246 /* Add the specified device instance data structure to the
3247  * global linked list of devices and increment the device count.
3248  */
3249 static void add_device(struct slgt_info *info)
3250 {
3251         char *devstr;
3252
3253         info->next_device = NULL;
3254         info->line = slgt_device_count;
3255         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3256
3257         if (info->line < MAX_DEVICES) {
3258                 if (maxframe[info->line])
3259                         info->max_frame_size = maxframe[info->line];
3260                 info->dosyncppp = dosyncppp[info->line];
3261         }
3262
3263         slgt_device_count++;
3264
3265         if (!slgt_device_list)
3266                 slgt_device_list = info;
3267         else {
3268                 struct slgt_info *current_dev = slgt_device_list;
3269                 while(current_dev->next_device)
3270                         current_dev = current_dev->next_device;
3271                 current_dev->next_device = info;
3272         }
3273
3274         if (info->max_frame_size < 4096)
3275                 info->max_frame_size = 4096;
3276         else if (info->max_frame_size > 65535)
3277                 info->max_frame_size = 65535;
3278
3279         switch(info->pdev->device) {
3280         case SYNCLINK_GT_DEVICE_ID:
3281                 devstr = "GT";
3282                 break;
3283         case SYNCLINK_GT4_DEVICE_ID:
3284                 devstr = "GT4";
3285                 break;
3286         case SYNCLINK_AC_DEVICE_ID:
3287                 devstr = "AC";
3288                 info->params.mode = MGSL_MODE_ASYNC;
3289                 break;
3290         default:
3291                 devstr = "(unknown model)";
3292         }
3293         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3294                 devstr, info->device_name, info->phys_reg_addr,
3295                 info->irq_level, info->max_frame_size);
3296
3297 #ifdef CONFIG_HDLC
3298         hdlcdev_init(info);
3299 #endif
3300 }
3301
3302 /*
3303  *  allocate device instance structure, return NULL on failure
3304  */
3305 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3306 {
3307         struct slgt_info *info;
3308
3309         info = kmalloc(sizeof(struct slgt_info), GFP_KERNEL);
3310
3311         if (!info) {
3312                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3313                         driver_name, adapter_num, port_num));
3314         } else {
3315                 memset(info, 0, sizeof(struct slgt_info));
3316                 info->magic = MGSL_MAGIC;
3317                 INIT_WORK(&info->task, bh_handler, info);
3318                 info->max_frame_size = 4096;
3319                 info->raw_rx_size = DMABUFSIZE;
3320                 info->close_delay = 5*HZ/10;
3321                 info->closing_wait = 30*HZ;
3322                 init_waitqueue_head(&info->open_wait);
3323                 init_waitqueue_head(&info->close_wait);
3324                 init_waitqueue_head(&info->status_event_wait_q);
3325                 init_waitqueue_head(&info->event_wait_q);
3326                 spin_lock_init(&info->netlock);
3327                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3328                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3329                 info->adapter_num = adapter_num;
3330                 info->port_num = port_num;
3331
3332                 init_timer(&info->tx_timer);
3333                 info->tx_timer.data = (unsigned long)info;
3334                 info->tx_timer.function = tx_timeout;
3335
3336                 init_timer(&info->rx_timer);
3337                 info->rx_timer.data = (unsigned long)info;
3338                 info->rx_timer.function = rx_timeout;
3339
3340                 /* Copy configuration info to device instance data */
3341                 info->pdev = pdev;
3342                 info->irq_level = pdev->irq;
3343                 info->phys_reg_addr = pci_resource_start(pdev,0);
3344
3345                 info->bus_type = MGSL_BUS_TYPE_PCI;
3346                 info->irq_flags = SA_SHIRQ;
3347
3348                 info->init_error = -1; /* assume error, set to 0 on successful init */
3349         }
3350
3351         return info;
3352 }
3353
3354 static void device_init(int adapter_num, struct pci_dev *pdev)
3355 {
3356         struct slgt_info *port_array[SLGT_MAX_PORTS];
3357         int i;
3358         int port_count = 1;
3359
3360         if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3361                 port_count = 4;
3362
3363         /* allocate device instances for all ports */
3364         for (i=0; i < port_count; ++i) {
3365                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3366                 if (port_array[i] == NULL) {
3367                         for (--i; i >= 0; --i)
3368                                 kfree(port_array[i]);
3369                         return;
3370                 }
3371         }
3372
3373         /* give copy of port_array to all ports and add to device list  */
3374         for (i=0; i < port_count; ++i) {
3375                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3376                 add_device(port_array[i]);
3377                 port_array[i]->port_count = port_count;
3378                 spin_lock_init(&port_array[i]->lock);
3379         }
3380
3381         /* Allocate and claim adapter resources */
3382         if (!claim_resources(port_array[0])) {
3383
3384                 alloc_dma_bufs(port_array[0]);
3385
3386                 /* copy resource information from first port to others */
3387                 for (i = 1; i < port_count; ++i) {
3388                         port_array[i]->lock      = port_array[0]->lock;
3389                         port_array[i]->irq_level = port_array[0]->irq_level;
3390                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3391                         alloc_dma_bufs(port_array[i]);
3392                 }
3393
3394                 if (request_irq(port_array[0]->irq_level,
3395                                         slgt_interrupt,
3396                                         port_array[0]->irq_flags,
3397                                         port_array[0]->device_name,
3398                                         port_array[0]) < 0) {
3399                         DBGERR(("%s request_irq failed IRQ=%d\n",
3400                                 port_array[0]->device_name,
3401                                 port_array[0]->irq_level));
3402                 } else {
3403                         port_array[0]->irq_requested = 1;
3404                         adapter_test(port_array[0]);
3405                         for (i=1 ; i < port_count ; i++) {
3406                                 port_array[i]->init_error = port_array[0]->init_error;
3407                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3408                         }
3409                 }
3410         }
3411 }
3412
3413 static int __devinit init_one(struct pci_dev *dev,
3414                               const struct pci_device_id *ent)
3415 {
3416         if (pci_enable_device(dev)) {
3417                 printk("error enabling pci device %p\n", dev);
3418                 return -EIO;
3419         }
3420         pci_set_master(dev);
3421         device_init(slgt_device_count, dev);
3422         return 0;
3423 }
3424
3425 static void __devexit remove_one(struct pci_dev *dev)
3426 {
3427 }
3428
3429 static struct tty_operations ops = {
3430         .open = open,
3431         .close = close,
3432         .write = write,
3433         .put_char = put_char,
3434         .flush_chars = flush_chars,
3435         .write_room = write_room,
3436         .chars_in_buffer = chars_in_buffer,
3437         .flush_buffer = flush_buffer,
3438         .ioctl = ioctl,
3439         .throttle = throttle,
3440         .unthrottle = unthrottle,
3441         .send_xchar = send_xchar,
3442         .break_ctl = set_break,
3443         .wait_until_sent = wait_until_sent,
3444         .read_proc = read_proc,
3445         .set_termios = set_termios,
3446         .stop = tx_hold,
3447         .start = tx_release,
3448         .hangup = hangup,
3449         .tiocmget = tiocmget,
3450         .tiocmset = tiocmset,
3451 };
3452
3453 static void slgt_cleanup(void)
3454 {
3455         int rc;
3456         struct slgt_info *info;
3457         struct slgt_info *tmp;
3458
3459         printk("unload %s %s\n", driver_name, driver_version);
3460
3461         if (serial_driver) {
3462                 if ((rc = tty_unregister_driver(serial_driver)))
3463                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3464                 put_tty_driver(serial_driver);
3465         }
3466
3467         /* reset devices */
3468         info = slgt_device_list;
3469         while(info) {
3470                 reset_port(info);
3471                 info = info->next_device;
3472         }
3473
3474         /* release devices */
3475         info = slgt_device_list;
3476         while(info) {
3477 #ifdef CONFIG_HDLC
3478                 hdlcdev_exit(info);
3479 #endif
3480                 free_dma_bufs(info);
3481                 free_tmp_rbuf(info);
3482                 if (info->port_num == 0)
3483                         release_resources(info);
3484                 tmp = info;
3485                 info = info->next_device;
3486                 kfree(tmp);
3487         }
3488
3489         if (pci_registered)
3490                 pci_unregister_driver(&pci_driver);
3491 }
3492
3493 /*
3494  *  Driver initialization entry point.
3495  */
3496 static int __init slgt_init(void)
3497 {
3498         int rc;
3499
3500         printk("%s %s\n", driver_name, driver_version);
3501
3502         slgt_device_count = 0;
3503         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3504                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3505                 return rc;
3506         }
3507         pci_registered = 1;
3508
3509         if (!slgt_device_list) {
3510                 printk("%s no devices found\n",driver_name);
3511                 return -ENODEV;
3512         }
3513
3514         serial_driver = alloc_tty_driver(MAX_DEVICES);
3515         if (!serial_driver) {
3516                 rc = -ENOMEM;
3517                 goto error;
3518         }
3519
3520         /* Initialize the tty_driver structure */
3521
3522         serial_driver->owner = THIS_MODULE;
3523         serial_driver->driver_name = tty_driver_name;
3524         serial_driver->name = tty_dev_prefix;
3525         serial_driver->major = ttymajor;
3526         serial_driver->minor_start = 64;
3527         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3528         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3529         serial_driver->init_termios = tty_std_termios;
3530         serial_driver->init_termios.c_cflag =
3531                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3532         serial_driver->flags = TTY_DRIVER_REAL_RAW;
3533         tty_set_operations(serial_driver, &ops);
3534         if ((rc = tty_register_driver(serial_driver)) < 0) {
3535                 DBGERR(("%s can't register serial driver\n", driver_name));
3536                 put_tty_driver(serial_driver);
3537                 serial_driver = NULL;
3538                 goto error;
3539         }
3540
3541         printk("%s %s, tty major#%d\n",
3542                 driver_name, driver_version,
3543                 serial_driver->major);
3544
3545         return 0;
3546
3547 error:
3548         slgt_cleanup();
3549         return rc;
3550 }
3551
3552 static void __exit slgt_exit(void)
3553 {
3554         slgt_cleanup();
3555 }
3556
3557 module_init(slgt_init);
3558 module_exit(slgt_exit);
3559
3560 /*
3561  * register access routines
3562  */
3563
3564 #define CALC_REGADDR() \
3565         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3566         if (addr >= 0x80) \
3567                 reg_addr += (info->port_num) * 32;
3568
3569 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3570 {
3571         CALC_REGADDR();
3572         return readb((void __iomem *)reg_addr);
3573 }
3574
3575 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3576 {
3577         CALC_REGADDR();
3578         writeb(value, (void __iomem *)reg_addr);
3579 }
3580
3581 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3582 {
3583         CALC_REGADDR();
3584         return readw((void __iomem *)reg_addr);
3585 }
3586
3587 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3588 {
3589         CALC_REGADDR();
3590         writew(value, (void __iomem *)reg_addr);
3591 }
3592
3593 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3594 {
3595         CALC_REGADDR();
3596         return readl((void __iomem *)reg_addr);
3597 }
3598
3599 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3600 {
3601         CALC_REGADDR();
3602         writel(value, (void __iomem *)reg_addr);
3603 }
3604
3605 static void rdma_reset(struct slgt_info *info)
3606 {
3607         unsigned int i;
3608
3609         /* set reset bit */
3610         wr_reg32(info, RDCSR, BIT1);
3611
3612         /* wait for enable bit cleared */
3613         for(i=0 ; i < 1000 ; i++)
3614                 if (!(rd_reg32(info, RDCSR) & BIT0))
3615                         break;
3616 }
3617
3618 static void tdma_reset(struct slgt_info *info)
3619 {
3620         unsigned int i;
3621
3622         /* set reset bit */
3623         wr_reg32(info, TDCSR, BIT1);
3624
3625         /* wait for enable bit cleared */
3626         for(i=0 ; i < 1000 ; i++)
3627                 if (!(rd_reg32(info, TDCSR) & BIT0))
3628                         break;
3629 }
3630
3631 /*
3632  * enable internal loopback
3633  * TxCLK and RxCLK are generated from BRG
3634  * and TxD is looped back to RxD internally.
3635  */
3636 static void enable_loopback(struct slgt_info *info)
3637 {
3638         /* SCR (serial control) BIT2=looopback enable */
3639         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3640
3641         if (info->params.mode != MGSL_MODE_ASYNC) {
3642                 /* CCR (clock control)
3643                  * 07..05  tx clock source (010 = BRG)
3644                  * 04..02  rx clock source (010 = BRG)
3645                  * 01      auxclk enable   (0 = disable)
3646                  * 00      BRG enable      (1 = enable)
3647                  *
3648                  * 0100 1001
3649                  */
3650                 wr_reg8(info, CCR, 0x49);
3651
3652                 /* set speed if available, otherwise use default */
3653                 if (info->params.clock_speed)
3654                         set_rate(info, info->params.clock_speed);
3655                 else
3656                         set_rate(info, 3686400);
3657         }
3658 }
3659
3660 /*
3661  *  set baud rate generator to specified rate
3662  */
3663 static void set_rate(struct slgt_info *info, u32 rate)
3664 {
3665         unsigned int div;
3666         static unsigned int osc = 14745600;
3667
3668         /* div = osc/rate - 1
3669          *
3670          * Round div up if osc/rate is not integer to
3671          * force to next slowest rate.
3672          */
3673
3674         if (rate) {
3675                 div = osc/rate;
3676                 if (!(osc % rate) && div)
3677                         div--;
3678                 wr_reg16(info, BDR, (unsigned short)div);
3679         }
3680 }
3681
3682 static void rx_stop(struct slgt_info *info)
3683 {
3684         unsigned short val;
3685
3686         /* disable and reset receiver */
3687         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3688         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3689         wr_reg16(info, RCR, val);                  /* clear reset bit */
3690
3691         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3692
3693         /* clear pending rx interrupts */
3694         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3695
3696         rdma_reset(info);
3697
3698         info->rx_enabled = 0;
3699         info->rx_restart = 0;
3700 }
3701
3702 static void rx_start(struct slgt_info *info)
3703 {
3704         unsigned short val;
3705
3706         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3707
3708         /* clear pending rx overrun IRQ */
3709         wr_reg16(info, SSR, IRQ_RXOVER);
3710
3711         /* reset and disable receiver */
3712         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3713         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3714         wr_reg16(info, RCR, val);                  /* clear reset bit */
3715
3716         rdma_reset(info);
3717         reset_rbufs(info);
3718
3719         /* set 1st descriptor address */
3720         wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3721
3722         if (info->params.mode != MGSL_MODE_ASYNC) {
3723                 /* enable rx DMA and DMA interrupt */
3724                 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3725         } else {
3726                 /* enable saving of rx status, rx DMA and DMA interrupt */
3727                 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3728         }
3729
3730         slgt_irq_on(info, IRQ_RXOVER);
3731
3732         /* enable receiver */
3733         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3734
3735         info->rx_restart = 0;
3736         info->rx_enabled = 1;
3737 }
3738
3739 static void tx_start(struct slgt_info *info)
3740 {
3741         if (!info->tx_enabled) {
3742                 wr_reg16(info, TCR,
3743                         (unsigned short)(rd_reg16(info, TCR) | BIT1));
3744                 info->tx_enabled = TRUE;
3745         }
3746
3747         if (info->tx_count) {
3748                 info->drop_rts_on_tx_done = 0;
3749
3750                 if (info->params.mode != MGSL_MODE_ASYNC) {
3751                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3752                                 get_signals(info);
3753                                 if (!(info->signals & SerialSignal_RTS)) {
3754                                         info->signals |= SerialSignal_RTS;
3755                                         set_signals(info);
3756                                         info->drop_rts_on_tx_done = 1;
3757                                 }
3758                         }
3759
3760                         slgt_irq_off(info, IRQ_TXDATA);
3761                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3762                         /* clear tx idle and underrun status bits */
3763                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3764
3765                         if (!(rd_reg32(info, TDCSR) & BIT0)) {
3766                                 /* tx DMA stopped, restart tx DMA */
3767                                 tdma_reset(info);
3768                                 /* set 1st descriptor address */
3769                                 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3770                                 if (info->params.mode == MGSL_MODE_RAW)
3771                                         wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
3772                                 else
3773                                         wr_reg32(info, TDCSR, BIT0); /* DMA enable */
3774                         }
3775
3776                         if (info->params.mode != MGSL_MODE_RAW) {
3777                                 info->tx_timer.expires = jiffies + msecs_to_jiffies(5000);
3778                                 add_timer(&info->tx_timer);
3779                         }
3780                 } else {
3781                         tdma_reset(info);
3782                         /* set 1st descriptor address */
3783                         wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3784
3785                         slgt_irq_off(info, IRQ_TXDATA);
3786                         slgt_irq_on(info, IRQ_TXIDLE);
3787                         /* clear tx idle status bit */
3788                         wr_reg16(info, SSR, IRQ_TXIDLE);
3789
3790                         /* enable tx DMA */
3791                         wr_reg32(info, TDCSR, BIT0);
3792                 }
3793
3794                 info->tx_active = 1;
3795         }
3796 }
3797
3798 static void tx_stop(struct slgt_info *info)
3799 {
3800         unsigned short val;
3801
3802         del_timer(&info->tx_timer);
3803
3804         tdma_reset(info);
3805
3806         /* reset and disable transmitter */
3807         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
3808         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3809         wr_reg16(info, TCR, val);                  /* clear reset */
3810
3811         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3812
3813         /* clear tx idle and underrun status bit */
3814         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3815
3816         reset_tbufs(info);
3817
3818         info->tx_enabled = 0;
3819         info->tx_active  = 0;
3820 }
3821
3822 static void reset_port(struct slgt_info *info)
3823 {
3824         if (!info->reg_addr)
3825                 return;
3826
3827         tx_stop(info);
3828         rx_stop(info);
3829
3830         info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
3831         set_signals(info);
3832
3833         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3834 }
3835
3836 static void reset_adapter(struct slgt_info *info)
3837 {
3838         int i;
3839         for (i=0; i < info->port_count; ++i) {
3840                 if (info->port_array[i])
3841                         reset_port(info->port_array[i]);
3842         }
3843 }
3844
3845 static void async_mode(struct slgt_info *info)
3846 {
3847         unsigned short val;
3848
3849         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3850         tx_stop(info);
3851         rx_stop(info);
3852
3853         /* TCR (tx control)
3854          *
3855          * 15..13  mode, 010=async
3856          * 12..10  encoding, 000=NRZ
3857          * 09      parity enable
3858          * 08      1=odd parity, 0=even parity
3859          * 07      1=RTS driver control
3860          * 06      1=break enable
3861          * 05..04  character length
3862          *         00=5 bits
3863          *         01=6 bits
3864          *         10=7 bits
3865          *         11=8 bits
3866          * 03      0=1 stop bit, 1=2 stop bits
3867          * 02      reset
3868          * 01      enable
3869          * 00      auto-CTS enable
3870          */
3871         val = 0x4000;
3872
3873         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
3874                 val |= BIT7;
3875
3876         if (info->params.parity != ASYNC_PARITY_NONE) {
3877                 val |= BIT9;
3878                 if (info->params.parity == ASYNC_PARITY_ODD)
3879                         val |= BIT8;
3880         }
3881
3882         switch (info->params.data_bits)
3883         {
3884         case 6: val |= BIT4; break;
3885         case 7: val |= BIT5; break;
3886         case 8: val |= BIT5 + BIT4; break;
3887         }
3888
3889         if (info->params.stop_bits != 1)
3890                 val |= BIT3;
3891
3892         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
3893                 val |= BIT0;
3894
3895         wr_reg16(info, TCR, val);
3896
3897         /* RCR (rx control)
3898          *
3899          * 15..13  mode, 010=async
3900          * 12..10  encoding, 000=NRZ
3901          * 09      parity enable
3902          * 08      1=odd parity, 0=even parity
3903          * 07..06  reserved, must be 0
3904          * 05..04  character length
3905          *         00=5 bits
3906          *         01=6 bits
3907          *         10=7 bits
3908          *         11=8 bits
3909          * 03      reserved, must be zero
3910          * 02      reset
3911          * 01      enable
3912          * 00      auto-DCD enable
3913          */
3914         val = 0x4000;
3915
3916         if (info->params.parity != ASYNC_PARITY_NONE) {
3917                 val |= BIT9;
3918                 if (info->params.parity == ASYNC_PARITY_ODD)
3919                         val |= BIT8;
3920         }
3921
3922         switch (info->params.data_bits)
3923         {
3924         case 6: val |= BIT4; break;
3925         case 7: val |= BIT5; break;
3926         case 8: val |= BIT5 + BIT4; break;
3927         }
3928
3929         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
3930                 val |= BIT0;
3931
3932         wr_reg16(info, RCR, val);
3933
3934         /* CCR (clock control)
3935          *
3936          * 07..05  011 = tx clock source is BRG/16
3937          * 04..02  010 = rx clock source is BRG
3938          * 01      0 = auxclk disabled
3939          * 00      1 = BRG enabled
3940          *
3941          * 0110 1001
3942          */
3943         wr_reg8(info, CCR, 0x69);
3944
3945         msc_set_vcr(info);
3946
3947         tx_set_idle(info);
3948
3949         /* SCR (serial control)
3950          *
3951          * 15  1=tx req on FIFO half empty
3952          * 14  1=rx req on FIFO half full
3953          * 13  tx data  IRQ enable
3954          * 12  tx idle  IRQ enable
3955          * 11  rx break on IRQ enable
3956          * 10  rx data  IRQ enable
3957          * 09  rx break off IRQ enable
3958          * 08  overrun  IRQ enable
3959          * 07  DSR      IRQ enable
3960          * 06  CTS      IRQ enable
3961          * 05  DCD      IRQ enable
3962          * 04  RI       IRQ enable
3963          * 03  reserved, must be zero
3964          * 02  1=txd->rxd internal loopback enable
3965          * 01  reserved, must be zero
3966          * 00  1=master IRQ enable
3967          */
3968         val = BIT15 + BIT14 + BIT0;
3969         wr_reg16(info, SCR, val);
3970
3971         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
3972
3973         set_rate(info, info->params.data_rate * 16);
3974
3975         if (info->params.loopback)
3976                 enable_loopback(info);
3977 }
3978
3979 static void hdlc_mode(struct slgt_info *info)
3980 {
3981         unsigned short val;
3982
3983         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3984         tx_stop(info);
3985         rx_stop(info);
3986
3987         /* TCR (tx control)
3988          *
3989          * 15..13  mode, 000=HDLC 001=raw sync
3990          * 12..10  encoding
3991          * 09      CRC enable
3992          * 08      CRC32
3993          * 07      1=RTS driver control
3994          * 06      preamble enable
3995          * 05..04  preamble length
3996          * 03      share open/close flag
3997          * 02      reset
3998          * 01      enable
3999          * 00      auto-CTS enable
4000          */
4001         val = 0;
4002
4003         if (info->params.mode == MGSL_MODE_RAW)
4004                 val |= BIT13;
4005         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4006                 val |= BIT7;
4007
4008         switch(info->params.encoding)
4009         {
4010         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4011         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4012         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4013         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4014         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4015         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4016         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4017         }
4018
4019         switch (info->params.crc_type)
4020         {
4021         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4022         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4023         }
4024
4025         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4026                 val |= BIT6;
4027
4028         switch (info->params.preamble_length)
4029         {
4030         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4031         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4032         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4033         }
4034
4035         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4036                 val |= BIT0;
4037
4038         wr_reg16(info, TCR, val);
4039
4040         /* TPR (transmit preamble) */
4041
4042         switch (info->params.preamble)
4043         {
4044         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4045         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4046         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4047         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4048         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4049         default:                          val = 0x7e; break;
4050         }
4051         wr_reg8(info, TPR, (unsigned char)val);
4052
4053         /* RCR (rx control)
4054          *
4055          * 15..13  mode, 000=HDLC 001=raw sync
4056          * 12..10  encoding
4057          * 09      CRC enable
4058          * 08      CRC32
4059          * 07..03  reserved, must be 0
4060          * 02      reset
4061          * 01      enable
4062          * 00      auto-DCD enable
4063          */
4064         val = 0;
4065
4066         if (info->params.mode == MGSL_MODE_RAW)
4067                 val |= BIT13;
4068
4069         switch(info->params.encoding)
4070         {
4071         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4072         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4073         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4074         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4075         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4076         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4077         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4078         }
4079
4080         switch (info->params.crc_type)
4081         {
4082         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4083         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4084         }
4085
4086         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4087                 val |= BIT0;
4088
4089         wr_reg16(info, RCR, val);
4090
4091         /* CCR (clock control)
4092          *
4093          * 07..05  tx clock source
4094          * 04..02  rx clock source
4095          * 01      auxclk enable
4096          * 00      BRG enable
4097          */
4098         val = 0;
4099
4100         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4101         {
4102                 // when RxC source is DPLL, BRG generates 16X DPLL
4103                 // reference clock, so take TxC from BRG/16 to get
4104                 // transmit clock at actual data rate
4105                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4106                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4107                 else
4108                         val |= BIT6;    /* 010, txclk = BRG */
4109         }
4110         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4111                 val |= BIT7;    /* 100, txclk = DPLL Input */
4112         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4113                 val |= BIT5;    /* 001, txclk = RXC Input */
4114
4115         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4116                 val |= BIT3;    /* 010, rxclk = BRG */
4117         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4118                 val |= BIT4;    /* 100, rxclk = DPLL */
4119         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4120                 val |= BIT2;    /* 001, rxclk = TXC Input */
4121
4122         if (info->params.clock_speed)
4123                 val |= BIT1 + BIT0;
4124
4125         wr_reg8(info, CCR, (unsigned char)val);
4126
4127         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4128         {
4129                 // program DPLL mode
4130                 switch(info->params.encoding)
4131                 {
4132                 case HDLC_ENCODING_BIPHASE_MARK:
4133                 case HDLC_ENCODING_BIPHASE_SPACE:
4134                         val = BIT7; break;
4135                 case HDLC_ENCODING_BIPHASE_LEVEL:
4136                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4137                         val = BIT7 + BIT6; break;
4138                 default: val = BIT6;    // NRZ encodings
4139                 }
4140                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4141
4142                 // DPLL requires a 16X reference clock from BRG
4143                 set_rate(info, info->params.clock_speed * 16);
4144         }
4145         else
4146                 set_rate(info, info->params.clock_speed);
4147
4148         tx_set_idle(info);
4149
4150         msc_set_vcr(info);
4151
4152         /* SCR (serial control)
4153          *
4154          * 15  1=tx req on FIFO half empty
4155          * 14  1=rx req on FIFO half full
4156          * 13  tx data  IRQ enable
4157          * 12  tx idle  IRQ enable
4158          * 11  underrun IRQ enable
4159          * 10  rx data  IRQ enable
4160          * 09  rx idle  IRQ enable
4161          * 08  overrun  IRQ enable
4162          * 07  DSR      IRQ enable
4163          * 06  CTS      IRQ enable
4164          * 05  DCD      IRQ enable
4165          * 04  RI       IRQ enable
4166          * 03  reserved, must be zero
4167          * 02  1=txd->rxd internal loopback enable
4168          * 01  reserved, must be zero
4169          * 00  1=master IRQ enable
4170          */
4171         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4172
4173         if (info->params.loopback)
4174                 enable_loopback(info);
4175 }
4176
4177 /*
4178  *  set transmit idle mode
4179  */
4180 static void tx_set_idle(struct slgt_info *info)
4181 {
4182         unsigned char val = 0xff;
4183
4184         switch(info->idle_mode)
4185         {
4186         case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4187         case HDLC_TXIDLE_ALT_ZEROS_ONES: val = 0xaa; break;
4188         case HDLC_TXIDLE_ZEROS:          val = 0x00; break;
4189         case HDLC_TXIDLE_ONES:           val = 0xff; break;
4190         case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4191         case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4192         case HDLC_TXIDLE_MARK:           val = 0xff; break;
4193         }
4194
4195         wr_reg8(info, TIR, val);
4196 }
4197
4198 /*
4199  * get state of V24 status (input) signals
4200  */
4201 static void get_signals(struct slgt_info *info)
4202 {
4203         unsigned short status = rd_reg16(info, SSR);
4204
4205         /* clear all serial signals except DTR and RTS */
4206         info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4207
4208         if (status & BIT3)
4209                 info->signals |= SerialSignal_DSR;
4210         if (status & BIT2)
4211                 info->signals |= SerialSignal_CTS;
4212         if (status & BIT1)
4213                 info->signals |= SerialSignal_DCD;
4214         if (status & BIT0)
4215                 info->signals |= SerialSignal_RI;
4216 }
4217
4218 /*
4219  * set V.24 Control Register based on current configuration
4220  */
4221 static void msc_set_vcr(struct slgt_info *info)
4222 {
4223         unsigned char val = 0;
4224
4225         /* VCR (V.24 control)
4226          *
4227          * 07..04  serial IF select
4228          * 03      DTR
4229          * 02      RTS
4230          * 01      LL
4231          * 00      RL
4232          */
4233
4234         switch(info->if_mode & MGSL_INTERFACE_MASK)
4235         {
4236         case MGSL_INTERFACE_RS232:
4237                 val |= BIT5; /* 0010 */
4238                 break;
4239         case MGSL_INTERFACE_V35:
4240                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4241                 break;
4242         case MGSL_INTERFACE_RS422:
4243                 val |= BIT6; /* 0100 */
4244                 break;
4245         }
4246
4247         if (info->signals & SerialSignal_DTR)
4248                 val |= BIT3;
4249         if (info->signals & SerialSignal_RTS)
4250                 val |= BIT2;
4251         if (info->if_mode & MGSL_INTERFACE_LL)
4252                 val |= BIT1;
4253         if (info->if_mode & MGSL_INTERFACE_RL)
4254                 val |= BIT0;
4255         wr_reg8(info, VCR, val);
4256 }
4257
4258 /*
4259  * set state of V24 control (output) signals
4260  */
4261 static void set_signals(struct slgt_info *info)
4262 {
4263         unsigned char val = rd_reg8(info, VCR);
4264         if (info->signals & SerialSignal_DTR)
4265                 val |= BIT3;
4266         else
4267                 val &= ~BIT3;
4268         if (info->signals & SerialSignal_RTS)
4269                 val |= BIT2;
4270         else
4271                 val &= ~BIT2;
4272         wr_reg8(info, VCR, val);
4273 }
4274
4275 /*
4276  * free range of receive DMA buffers (i to last)
4277  */
4278 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4279 {
4280         int done = 0;
4281
4282         while(!done) {
4283                 /* reset current buffer for reuse */
4284                 info->rbufs[i].status = 0;
4285                 if (info->params.mode == MGSL_MODE_RAW)
4286                         set_desc_count(info->rbufs[i], info->raw_rx_size);
4287                 else
4288                         set_desc_count(info->rbufs[i], DMABUFSIZE);
4289
4290                 if (i == last)
4291                         done = 1;
4292                 if (++i == info->rbuf_count)
4293                         i = 0;
4294         }
4295         info->rbuf_current = i;
4296 }
4297
4298 /*
4299  * mark all receive DMA buffers as free
4300  */
4301 static void reset_rbufs(struct slgt_info *info)
4302 {
4303         free_rbufs(info, 0, info->rbuf_count - 1);
4304 }
4305
4306 /*
4307  * pass receive HDLC frame to upper layer
4308  *
4309  * return 1 if frame available, otherwise 0
4310  */
4311 static int rx_get_frame(struct slgt_info *info)
4312 {
4313         unsigned int start, end;
4314         unsigned short status;
4315         unsigned int framesize = 0;
4316         int rc = 0;
4317         unsigned long flags;
4318         struct tty_struct *tty = info->tty;
4319         unsigned char addr_field = 0xff;
4320
4321 check_again:
4322
4323         framesize = 0;
4324         addr_field = 0xff;
4325         start = end = info->rbuf_current;
4326
4327         for (;;) {
4328                 if (!desc_complete(info->rbufs[end]))
4329                         goto cleanup;
4330
4331                 if (framesize == 0 && info->params.addr_filter != 0xff)
4332                         addr_field = info->rbufs[end].buf[0];
4333
4334                 framesize += desc_count(info->rbufs[end]);
4335
4336                 if (desc_eof(info->rbufs[end]))
4337                         break;
4338
4339                 if (++end == info->rbuf_count)
4340                         end = 0;
4341
4342                 if (end == info->rbuf_current) {
4343                         if (info->rx_enabled){
4344                                 spin_lock_irqsave(&info->lock,flags);
4345                                 rx_start(info);
4346                                 spin_unlock_irqrestore(&info->lock,flags);
4347                         }
4348                         goto cleanup;
4349                 }
4350         }
4351
4352         /* status
4353          *
4354          * 15      buffer complete
4355          * 14..06  reserved
4356          * 05..04  residue
4357          * 02      eof (end of frame)
4358          * 01      CRC error
4359          * 00      abort
4360          */
4361         status = desc_status(info->rbufs[end]);
4362
4363         /* ignore CRC bit if not using CRC (bit is undefined) */
4364         if (info->params.crc_type == HDLC_CRC_NONE)
4365                 status &= ~BIT1;
4366
4367         if (framesize == 0 ||
4368                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4369                 free_rbufs(info, start, end);
4370                 goto check_again;
4371         }
4372
4373         if (framesize < 2 || status & (BIT1+BIT0)) {
4374                 if (framesize < 2 || (status & BIT0))
4375                         info->icount.rxshort++;
4376                 else
4377                         info->icount.rxcrc++;
4378                 framesize = 0;
4379
4380 #ifdef CONFIG_HDLC
4381                 {
4382                         struct net_device_stats *stats = hdlc_stats(info->netdev);
4383                         stats->rx_errors++;
4384                         stats->rx_frame_errors++;
4385                 }
4386 #endif
4387         } else {
4388                 /* adjust frame size for CRC, if any */
4389                 if (info->params.crc_type == HDLC_CRC_16_CCITT)
4390                         framesize -= 2;
4391                 else if (info->params.crc_type == HDLC_CRC_32_CCITT)
4392                         framesize -= 4;
4393         }
4394
4395         DBGBH(("%s rx frame status=%04X size=%d\n",
4396                 info->device_name, status, framesize));
4397         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, DMABUFSIZE), "rx");
4398
4399         if (framesize) {
4400                 if (framesize > info->max_frame_size)
4401                         info->icount.rxlong++;
4402                 else {
4403                         /* copy dma buffer(s) to contiguous temp buffer */
4404                         int copy_count = framesize;
4405                         int i = start;
4406                         unsigned char *p = info->tmp_rbuf;
4407                         info->tmp_rbuf_count = framesize;
4408
4409                         info->icount.rxok++;
4410
4411                         while(copy_count) {
4412                                 int partial_count = min(copy_count, DMABUFSIZE);
4413                                 memcpy(p, info->rbufs[i].buf, partial_count);
4414                                 p += partial_count;
4415                                 copy_count -= partial_count;
4416                                 if (++i == info->rbuf_count)
4417                                         i = 0;
4418                         }
4419
4420 #ifdef CONFIG_HDLC
4421                         if (info->netcount)
4422                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4423                         else
4424 #endif
4425                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4426                 }
4427         }
4428         free_rbufs(info, start, end);
4429         rc = 1;
4430
4431 cleanup:
4432         return rc;
4433 }
4434
4435 /*
4436  * pass receive buffer (RAW synchronous mode) to tty layer
4437  * return 1 if buffer available, otherwise 0
4438  */
4439 static int rx_get_buf(struct slgt_info *info)
4440 {
4441         unsigned int i = info->rbuf_current;
4442
4443         if (!desc_complete(info->rbufs[i]))
4444                 return 0;
4445         DBGDATA(info, info->rbufs[i].buf, desc_count(info->rbufs[i]), "rx");
4446         DBGINFO(("rx_get_buf size=%d\n", desc_count(info->rbufs[i])));
4447         ldisc_receive_buf(info->tty, info->rbufs[i].buf,
4448                           info->flag_buf, desc_count(info->rbufs[i]));
4449         free_rbufs(info, i, i);
4450         return 1;
4451 }
4452
4453 static void reset_tbufs(struct slgt_info *info)
4454 {
4455         unsigned int i;
4456         info->tbuf_current = 0;
4457         for (i=0 ; i < info->tbuf_count ; i++) {
4458                 info->tbufs[i].status = 0;
4459                 info->tbufs[i].count  = 0;
4460         }
4461 }
4462
4463 /*
4464  * return number of free transmit DMA buffers
4465  */
4466 static unsigned int free_tbuf_count(struct slgt_info *info)
4467 {
4468         unsigned int count = 0;
4469         unsigned int i = info->tbuf_current;
4470
4471         do
4472         {
4473                 if (desc_count(info->tbufs[i]))
4474                         break; /* buffer in use */
4475                 ++count;
4476                 if (++i == info->tbuf_count)
4477                         i=0;
4478         } while (i != info->tbuf_current);
4479
4480         /* last buffer with zero count may be in use, assume it is */
4481         if (count)
4482                 --count;
4483
4484         return count;
4485 }
4486
4487 /*
4488  * load transmit DMA buffer(s) with data
4489  */
4490 static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4491 {
4492         unsigned short count;
4493         unsigned int i;
4494         struct slgt_desc *d;
4495
4496         if (size == 0)
4497                 return;
4498
4499         DBGDATA(info, buf, size, "tx");
4500
4501         info->tbuf_start = i = info->tbuf_current;
4502
4503         while (size) {
4504                 d = &info->tbufs[i];
4505                 if (++i == info->tbuf_count)
4506                         i = 0;
4507
4508                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4509                 memcpy(d->buf, buf, count);
4510
4511                 size -= count;
4512                 buf  += count;
4513
4514                 if (!size && info->params.mode != MGSL_MODE_RAW)
4515                         set_desc_eof(*d, 1); /* HDLC: set EOF of last desc */
4516                 else
4517                         set_desc_eof(*d, 0);
4518
4519                 set_desc_count(*d, count);
4520         }
4521
4522         info->tbuf_current = i;
4523 }
4524
4525 static int register_test(struct slgt_info *info)
4526 {
4527         static unsigned short patterns[] =
4528                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4529         static unsigned int count = sizeof(patterns)/sizeof(patterns[0]);
4530         unsigned int i;
4531         int rc = 0;
4532
4533         for (i=0 ; i < count ; i++) {
4534                 wr_reg16(info, TIR, patterns[i]);
4535                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4536                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4537                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4538                         rc = -ENODEV;
4539                         break;
4540                 }
4541         }
4542         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4543         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4544         return rc;
4545 }
4546
4547 static int irq_test(struct slgt_info *info)
4548 {
4549         unsigned long timeout;
4550         unsigned long flags;
4551         struct tty_struct *oldtty = info->tty;
4552         u32 speed = info->params.data_rate;
4553
4554         info->params.data_rate = 921600;
4555         info->tty = NULL;
4556
4557         spin_lock_irqsave(&info->lock, flags);
4558         async_mode(info);
4559         slgt_irq_on(info, IRQ_TXIDLE);
4560
4561         /* enable transmitter */
4562         wr_reg16(info, TCR,
4563                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4564
4565         /* write one byte and wait for tx idle */
4566         wr_reg16(info, TDR, 0);
4567
4568         /* assume failure */
4569         info->init_error = DiagStatus_IrqFailure;
4570         info->irq_occurred = FALSE;
4571
4572         spin_unlock_irqrestore(&info->lock, flags);
4573
4574         timeout=100;
4575         while(timeout-- && !info->irq_occurred)
4576                 msleep_interruptible(10);
4577
4578         spin_lock_irqsave(&info->lock,flags);
4579         reset_port(info);
4580         spin_unlock_irqrestore(&info->lock,flags);
4581
4582         info->params.data_rate = speed;
4583         info->tty = oldtty;
4584
4585         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4586         return info->irq_occurred ? 0 : -ENODEV;
4587 }
4588
4589 static int loopback_test_rx(struct slgt_info *info)
4590 {
4591         unsigned char *src, *dest;
4592         int count;
4593
4594         if (desc_complete(info->rbufs[0])) {
4595                 count = desc_count(info->rbufs[0]);
4596                 src   = info->rbufs[0].buf;
4597                 dest  = info->tmp_rbuf;
4598
4599                 for( ; count ; count-=2, src+=2) {
4600                         /* src=data byte (src+1)=status byte */
4601                         if (!(*(src+1) & (BIT9 + BIT8))) {
4602                                 *dest = *src;
4603                                 dest++;
4604                                 info->tmp_rbuf_count++;
4605                         }
4606                 }
4607                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4608                 return 1;
4609         }
4610         return 0;
4611 }
4612
4613 static int loopback_test(struct slgt_info *info)
4614 {
4615 #define TESTFRAMESIZE 20
4616
4617         unsigned long timeout;
4618         u16 count = TESTFRAMESIZE;
4619         unsigned char buf[TESTFRAMESIZE];
4620         int rc = -ENODEV;
4621         unsigned long flags;
4622
4623         struct tty_struct *oldtty = info->tty;
4624         MGSL_PARAMS params;
4625
4626         memcpy(&params, &info->params, sizeof(params));
4627
4628         info->params.mode = MGSL_MODE_ASYNC;
4629         info->params.data_rate = 921600;
4630         info->params.loopback = 1;
4631         info->tty = NULL;
4632
4633         /* build and send transmit frame */
4634         for (count = 0; count < TESTFRAMESIZE; ++count)
4635                 buf[count] = (unsigned char)count;
4636
4637         info->tmp_rbuf_count = 0;
4638         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4639
4640         /* program hardware for HDLC and enabled receiver */
4641         spin_lock_irqsave(&info->lock,flags);
4642         async_mode(info);
4643         rx_start(info);
4644         info->tx_count = count;
4645         tx_load(info, buf, count);
4646         tx_start(info);
4647         spin_unlock_irqrestore(&info->lock, flags);
4648
4649         /* wait for receive complete */
4650         for (timeout = 100; timeout; --timeout) {
4651                 msleep_interruptible(10);
4652                 if (loopback_test_rx(info)) {
4653                         rc = 0;
4654                         break;
4655                 }
4656         }
4657
4658         /* verify received frame length and contents */
4659         if (!rc && (info->tmp_rbuf_count != count ||
4660                   memcmp(buf, info->tmp_rbuf, count))) {
4661                 rc = -ENODEV;
4662         }
4663
4664         spin_lock_irqsave(&info->lock,flags);
4665         reset_adapter(info);
4666         spin_unlock_irqrestore(&info->lock,flags);
4667
4668         memcpy(&info->params, &params, sizeof(info->params));
4669         info->tty = oldtty;
4670
4671         info->init_error = rc ? DiagStatus_DmaFailure : 0;
4672         return rc;
4673 }
4674
4675 static int adapter_test(struct slgt_info *info)
4676 {
4677         DBGINFO(("testing %s\n", info->device_name));
4678         if ((info->init_error = register_test(info)) < 0) {
4679                 printk("register test failure %s addr=%08X\n",
4680                         info->device_name, info->phys_reg_addr);
4681         } else if ((info->init_error = irq_test(info)) < 0) {
4682                 printk("IRQ test failure %s IRQ=%d\n",
4683                         info->device_name, info->irq_level);
4684         } else if ((info->init_error = loopback_test(info)) < 0) {
4685                 printk("loopback test failure %s\n", info->device_name);
4686         }
4687         return info->init_error;
4688 }
4689
4690 /*
4691  * transmit timeout handler
4692  */
4693 static void tx_timeout(unsigned long context)
4694 {
4695         struct slgt_info *info = (struct slgt_info*)context;
4696         unsigned long flags;
4697
4698         DBGINFO(("%s tx_timeout\n", info->device_name));
4699         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
4700                 info->icount.txtimeout++;
4701         }
4702         spin_lock_irqsave(&info->lock,flags);
4703         info->tx_active = 0;
4704         info->tx_count = 0;
4705         spin_unlock_irqrestore(&info->lock,flags);
4706
4707 #ifdef CONFIG_HDLC
4708         if (info->netcount)
4709                 hdlcdev_tx_done(info);
4710         else
4711 #endif
4712                 bh_transmit(info);
4713 }
4714
4715 /*
4716  * receive buffer polling timer
4717  */
4718 static void rx_timeout(unsigned long context)
4719 {
4720         struct slgt_info *info = (struct slgt_info*)context;
4721         unsigned long flags;
4722
4723         DBGINFO(("%s rx_timeout\n", info->device_name));
4724         spin_lock_irqsave(&info->lock, flags);
4725         info->pending_bh |= BH_RECEIVE;
4726         spin_unlock_irqrestore(&info->lock, flags);
4727         bh_handler(info);
4728 }
4729