drivers/char/synclink_gt.c

   1 /*
   2  * $Id: synclink_gt.c,v 4.50 2007/07/25 19:29:25 paulkf Exp $
   3  *
   4  * Device driver for Microgate SyncLink GT serial adapters.
   5  *
   6  * written by Paul Fulghum for Microgate Corporation
   7  * paulkf@microgate.com
   8  *
   9  * Microgate and SyncLink are trademarks of Microgate Corporation
  10  *
  11  * This code is released under the GNU General Public License (GPL)
  12  *
  13  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  14  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  15  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  16  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  17  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  18  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  19  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  20  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  21  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  22  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  23  * OF THE POSSIBILITY OF SUCH DAMAGE.
  24  */
  25
  26 /*
  27  * DEBUG OUTPUT DEFINITIONS
  28  *
  29  * uncomment lines below to enable specific types of debug output
  30  *
  31  * DBGINFO   information - most verbose output
  32  * DBGERR    serious errors
  33  * DBGBH     bottom half service routine debugging
  34  * DBGISR    interrupt service routine debugging
  35  * DBGDATA   output receive and transmit data
  36  * DBGTBUF   output transmit DMA buffers and registers
  37  * DBGRBUF   output receive DMA buffers and registers
  38  */
  39
  40 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  41 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  42 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  43 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  44 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  45 //#define DBGTBUF(info) dump_tbufs(info)
  46 //#define DBGRBUF(info) dump_rbufs(info)
  47
  48
  49 #include <linux/module.h>
  50 #include <linux/version.h>
  51 #include <linux/errno.h>
  52 #include <linux/signal.h>
  53 #include <linux/sched.h>
  54 #include <linux/timer.h>
  55 #include <linux/interrupt.h>
  56 #include <linux/pci.h>
  57 #include <linux/tty.h>
  58 #include <linux/tty_flip.h>
  59 #include <linux/serial.h>
  60 #include <linux/major.h>
  61 #include <linux/string.h>
  62 #include <linux/fcntl.h>
  63 #include <linux/ptrace.h>
  64 #include <linux/ioport.h>
  65 #include <linux/mm.h>
  66 #include <linux/slab.h>
  67 #include <linux/netdevice.h>
  68 #include <linux/vmalloc.h>
  69 #include <linux/init.h>
  70 #include <linux/delay.h>
  71 #include <linux/ioctl.h>
  72 #include <linux/termios.h>
  73 #include <linux/bitops.h>
  74 #include <linux/workqueue.h>
  75 #include <linux/hdlc.h>
  76 #include <linux/synclink.h>
  77
  78 #include <asm/system.h>
  79 #include <asm/io.h>
  80 #include <asm/irq.h>
  81 #include <asm/dma.h>
  82 #include <asm/types.h>
  83 #include <asm/uaccess.h>
  84
  85 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
  86 #define SYNCLINK_GENERIC_HDLC 1
  87 #else
  88 #define SYNCLINK_GENERIC_HDLC 0
  89 #endif
  90
  91 /*
  92  * module identification
  93  */
  94 static char *driver_name     = "SyncLink GT";
  95 static char *driver_version  = "$Revision: 4.50 $";
  96 static char *tty_driver_name = "synclink_gt";
  97 static char *tty_dev_prefix  = "ttySLG";
  98 MODULE_LICENSE("GPL");
  99 #define MGSL_MAGIC 0x5401
 100 #define MAX_DEVICES 32
 101
 102 static struct pci_device_id pci_table[] = {
 103         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 104         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 105         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 106         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 107         {0,}, /* terminate list */
 108 };
 109 MODULE_DEVICE_TABLE(pci, pci_table);
 110
 111 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 112 static void remove_one(struct pci_dev *dev);
 113 static struct pci_driver pci_driver = {
 114         .name           = "synclink_gt",
 115         .id_table       = pci_table,
 116         .probe          = init_one,
 117         .remove         = __devexit_p(remove_one),
 118 };
 119
 120 static bool pci_registered;
 121
 122 /*
 123  * module configuration and status
 124  */
 125 static struct slgt_info *slgt_device_list;
 126 static int slgt_device_count;
 127
 128 static int ttymajor;
 129 static int debug_level;
 130 static int maxframe[MAX_DEVICES];
 131
 132 module_param(ttymajor, int, 0);
 133 module_param(debug_level, int, 0);
 134 module_param_array(maxframe, int, NULL, 0);
 135
 136 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 137 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 138 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 139
 140 /*
 141  * tty support and callbacks
 142  */
 143 static struct tty_driver *serial_driver;
 144
 145 static int  open(struct tty_struct *tty, struct file * filp);
 146 static void close(struct tty_struct *tty, struct file * filp);
 147 static void hangup(struct tty_struct *tty);
 148 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
 149
 150 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 151 static int put_char(struct tty_struct *tty, unsigned char ch);
 152 static void send_xchar(struct tty_struct *tty, char ch);
 153 static void wait_until_sent(struct tty_struct *tty, int timeout);
 154 static int  write_room(struct tty_struct *tty);
 155 static void flush_chars(struct tty_struct *tty);
 156 static void flush_buffer(struct tty_struct *tty);
 157 static void tx_hold(struct tty_struct *tty);
 158 static void tx_release(struct tty_struct *tty);
 159
 160 static int  ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
 161 static int  read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
 162 static int  chars_in_buffer(struct tty_struct *tty);
 163 static void throttle(struct tty_struct * tty);
 164 static void unthrottle(struct tty_struct * tty);
 165 static int set_break(struct tty_struct *tty, int break_state);
 166
 167 /*
 168  * generic HDLC support and callbacks
 169  */
 170 #if SYNCLINK_GENERIC_HDLC
 171 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 172 static void hdlcdev_tx_done(struct slgt_info *info);
 173 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 174 static int  hdlcdev_init(struct slgt_info *info);
 175 static void hdlcdev_exit(struct slgt_info *info);
 176 #endif
 177
 178
 179 /*
 180  * device specific structures, macros and functions
 181  */
 182
 183 #define SLGT_MAX_PORTS 4
 184 #define SLGT_REG_SIZE  256
 185
 186 /*
 187  * conditional wait facility
 188  */
 189 struct cond_wait {
 190         struct cond_wait *next;
 191         wait_queue_head_t q;
 192         wait_queue_t wait;
 193         unsigned int data;
 194 };
 195 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 196 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 197 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 198 static void flush_cond_wait(struct cond_wait **head);
 199
 200 /*
 201  * DMA buffer descriptor and access macros
 202  */
 203 struct slgt_desc
 204 {
 205         __le16 count;
 206         __le16 status;
 207         __le32 pbuf;  /* physical address of data buffer */
 208         __le32 next;  /* physical address of next descriptor */
 209
 210         /* driver book keeping */
 211         char *buf;          /* virtual  address of data buffer */
 212         unsigned int pdesc; /* physical address of this descriptor */
 213         dma_addr_t buf_dma_addr;
 214         unsigned short buf_count;
 215 };
 216
 217 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 218 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 219 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 220 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 221 #define desc_count(a)      (le16_to_cpu((a).count))
 222 #define desc_status(a)     (le16_to_cpu((a).status))
 223 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 224 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 225 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 226 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 227 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 228
 229 struct _input_signal_events {
 230         int ri_up;
 231         int ri_down;
 232         int dsr_up;
 233         int dsr_down;
 234         int dcd_up;
 235         int dcd_down;
 236         int cts_up;
 237         int cts_down;
 238 };
 239
 240 /*
 241  * device instance data structure
 242  */
 243 struct slgt_info {
 244         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 245         struct tty_port port;
 246
 247         struct slgt_info *next_device;  /* device list link */
 248
 249         int magic;
 250
 251         char device_name[25];
 252         struct pci_dev *pdev;
 253
 254         int port_count;  /* count of ports on adapter */
 255         int adapter_num; /* adapter instance number */
 256         int port_num;    /* port instance number */
 257
 258         /* array of pointers to port contexts on this adapter */
 259         struct slgt_info *port_array[SLGT_MAX_PORTS];
 260
 261         int                     line;           /* tty line instance number */
 262
 263         struct mgsl_icount      icount;
 264
 265         int                     timeout;
 266         int                     x_char;         /* xon/xoff character */
 267         unsigned int            read_status_mask;
 268         unsigned int            ignore_status_mask;
 269
 270         wait_queue_head_t       status_event_wait_q;
 271         wait_queue_head_t       event_wait_q;
 272         struct timer_list       tx_timer;
 273         struct timer_list       rx_timer;
 274
 275         unsigned int            gpio_present;
 276         struct cond_wait        *gpio_wait_q;
 277
 278         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 279
 280         struct work_struct task;
 281         u32 pending_bh;
 282         bool bh_requested;
 283         bool bh_running;
 284
 285         int isr_overflow;
 286         bool irq_requested;     /* true if IRQ requested */
 287         bool irq_occurred;      /* for diagnostics use */
 288
 289         /* device configuration */
 290
 291         unsigned int bus_type;
 292         unsigned int irq_level;
 293         unsigned long irq_flags;
 294
 295         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 296         u32 phys_reg_addr;
 297         bool reg_addr_requested;
 298
 299         MGSL_PARAMS params;       /* communications parameters */
 300         u32 idle_mode;
 301         u32 max_frame_size;       /* as set by device config */
 302
 303         unsigned int rbuf_fill_level;
 304         unsigned int if_mode;
 305
 306         /* device status */
 307
 308         bool rx_enabled;
 309         bool rx_restart;
 310
 311         bool tx_enabled;
 312         bool tx_active;
 313
 314         unsigned char signals;    /* serial signal states */
 315         int init_error;  /* initialization error */
 316
 317         unsigned char *tx_buf;
 318         int tx_count;
 319
 320         char flag_buf[MAX_ASYNC_BUFFER_SIZE];
 321         char char_buf[MAX_ASYNC_BUFFER_SIZE];
 322         bool drop_rts_on_tx_done;
 323         struct  _input_signal_events    input_signal_events;
 324
 325         int dcd_chkcount;       /* check counts to prevent */
 326         int cts_chkcount;       /* too many IRQs if a signal */
 327         int dsr_chkcount;       /* is floating */
 328         int ri_chkcount;
 329
 330         char *bufs;             /* virtual address of DMA buffer lists */
 331         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 332
 333         unsigned int rbuf_count;
 334         struct slgt_desc *rbufs;
 335         unsigned int rbuf_current;
 336         unsigned int rbuf_index;
 337
 338         unsigned int tbuf_count;
 339         struct slgt_desc *tbufs;
 340         unsigned int tbuf_current;
 341         unsigned int tbuf_start;
 342
 343         unsigned char *tmp_rbuf;
 344         unsigned int tmp_rbuf_count;
 345
 346         /* SPPP/Cisco HDLC device parts */
 347
 348         int netcount;
 349         spinlock_t netlock;
 350 #if SYNCLINK_GENERIC_HDLC
 351         struct net_device *netdev;
 352 #endif
 353
 354 };
 355
 356 static MGSL_PARAMS default_params = {
 357         .mode            = MGSL_MODE_HDLC,
 358         .loopback        = 0,
 359         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 360         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 361         .clock_speed     = 0,
 362         .addr_filter     = 0xff,
 363         .crc_type        = HDLC_CRC_16_CCITT,
 364         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 365         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 366         .data_rate       = 9600,
 367         .data_bits       = 8,
 368         .stop_bits       = 1,
 369         .parity          = ASYNC_PARITY_NONE
 370 };
 371
 372
 373 #define BH_RECEIVE  1
 374 #define BH_TRANSMIT 2
 375 #define BH_STATUS   4
 376 #define IO_PIN_SHUTDOWN_LIMIT 100
 377
 378 #define DMABUFSIZE 256
 379 #define DESC_LIST_SIZE 4096
 380
 381 #define MASK_PARITY  BIT1
 382 #define MASK_FRAMING BIT0
 383 #define MASK_BREAK   BIT14
 384 #define MASK_OVERRUN BIT4
 385
 386 #define GSR   0x00 /* global status */
 387 #define JCR   0x04 /* JTAG control */
 388 #define IODR  0x08 /* GPIO direction */
 389 #define IOER  0x0c /* GPIO interrupt enable */
 390 #define IOVR  0x10 /* GPIO value */
 391 #define IOSR  0x14 /* GPIO interrupt status */
 392 #define TDR   0x80 /* tx data */
 393 #define RDR   0x80 /* rx data */
 394 #define TCR   0x82 /* tx control */
 395 #define TIR   0x84 /* tx idle */
 396 #define TPR   0x85 /* tx preamble */
 397 #define RCR   0x86 /* rx control */
 398 #define VCR   0x88 /* V.24 control */
 399 #define CCR   0x89 /* clock control */
 400 #define BDR   0x8a /* baud divisor */
 401 #define SCR   0x8c /* serial control */
 402 #define SSR   0x8e /* serial status */
 403 #define RDCSR 0x90 /* rx DMA control/status */
 404 #define TDCSR 0x94 /* tx DMA control/status */
 405 #define RDDAR 0x98 /* rx DMA descriptor address */
 406 #define TDDAR 0x9c /* tx DMA descriptor address */
 407
 408 #define RXIDLE      BIT14
 409 #define RXBREAK     BIT14
 410 #define IRQ_TXDATA  BIT13
 411 #define IRQ_TXIDLE  BIT12
 412 #define IRQ_TXUNDER BIT11 /* HDLC */
 413 #define IRQ_RXDATA  BIT10
 414 #define IRQ_RXIDLE  BIT9  /* HDLC */
 415 #define IRQ_RXBREAK BIT9  /* async */
 416 #define IRQ_RXOVER  BIT8
 417 #define IRQ_DSR     BIT7
 418 #define IRQ_CTS     BIT6
 419 #define IRQ_DCD     BIT5
 420 #define IRQ_RI      BIT4
 421 #define IRQ_ALL     0x3ff0
 422 #define IRQ_MASTER  BIT0
 423
 424 #define slgt_irq_on(info, mask) \
 425         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 426 #define slgt_irq_off(info, mask) \
 427         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 428
 429 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 430 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 431 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 432 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 433 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 434 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 435
 436 static void  msc_set_vcr(struct slgt_info *info);
 437
 438 static int  startup(struct slgt_info *info);
 439 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 440 static void shutdown(struct slgt_info *info);
 441 static void program_hw(struct slgt_info *info);
 442 static void change_params(struct slgt_info *info);
 443
 444 static int  register_test(struct slgt_info *info);
 445 static int  irq_test(struct slgt_info *info);
 446 static int  loopback_test(struct slgt_info *info);
 447 static int  adapter_test(struct slgt_info *info);
 448
 449 static void reset_adapter(struct slgt_info *info);
 450 static void reset_port(struct slgt_info *info);
 451 static void async_mode(struct slgt_info *info);
 452 static void sync_mode(struct slgt_info *info);
 453
 454 static void rx_stop(struct slgt_info *info);
 455 static void rx_start(struct slgt_info *info);
 456 static void reset_rbufs(struct slgt_info *info);
 457 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 458 static void rdma_reset(struct slgt_info *info);
 459 static bool rx_get_frame(struct slgt_info *info);
 460 static bool rx_get_buf(struct slgt_info *info);
 461
 462 static void tx_start(struct slgt_info *info);
 463 static void tx_stop(struct slgt_info *info);
 464 static void tx_set_idle(struct slgt_info *info);
 465 static unsigned int free_tbuf_count(struct slgt_info *info);
 466 static unsigned int tbuf_bytes(struct slgt_info *info);
 467 static void reset_tbufs(struct slgt_info *info);
 468 static void tdma_reset(struct slgt_info *info);
 469 static void tdma_start(struct slgt_info *info);
 470 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 471
 472 static void get_signals(struct slgt_info *info);
 473 static void set_signals(struct slgt_info *info);
 474 static void enable_loopback(struct slgt_info *info);
 475 static void set_rate(struct slgt_info *info, u32 data_rate);
 476
 477 static int  bh_action(struct slgt_info *info);
 478 static void bh_handler(struct work_struct *work);
 479 static void bh_transmit(struct slgt_info *info);
 480 static void isr_serial(struct slgt_info *info);
 481 static void isr_rdma(struct slgt_info *info);
 482 static void isr_txeom(struct slgt_info *info, unsigned short status);
 483 static void isr_tdma(struct slgt_info *info);
 484
 485 static int  alloc_dma_bufs(struct slgt_info *info);
 486 static void free_dma_bufs(struct slgt_info *info);
 487 static int  alloc_desc(struct slgt_info *info);
 488 static void free_desc(struct slgt_info *info);
 489 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 490 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 491
 492 static int  alloc_tmp_rbuf(struct slgt_info *info);
 493 static void free_tmp_rbuf(struct slgt_info *info);
 494
 495 static void tx_timeout(unsigned long context);
 496 static void rx_timeout(unsigned long context);
 497
 498 /*
 499  * ioctl handlers
 500  */
 501 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 502 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 503 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 504 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 505 static int  set_txidle(struct slgt_info *info, int idle_mode);
 506 static int  tx_enable(struct slgt_info *info, int enable);
 507 static int  tx_abort(struct slgt_info *info);
 508 static int  rx_enable(struct slgt_info *info, int enable);
 509 static int  modem_input_wait(struct slgt_info *info,int arg);
 510 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 511 static int  tiocmget(struct tty_struct *tty, struct file *file);
 512 static int  tiocmset(struct tty_struct *tty, struct file *file,
 513                      unsigned int set, unsigned int clear);
 514 static int set_break(struct tty_struct *tty, int break_state);
 515 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 516 static int  set_interface(struct slgt_info *info, int if_mode);
 517 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 518 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 519 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 520
 521 /*
 522  * driver functions
 523  */
 524 static void add_device(struct slgt_info *info);
 525 static void device_init(int adapter_num, struct pci_dev *pdev);
 526 static int  claim_resources(struct slgt_info *info);
 527 static void release_resources(struct slgt_info *info);
 528
 529 /*
 530  * DEBUG OUTPUT CODE
 531  */
 532 #ifndef DBGINFO
 533 #define DBGINFO(fmt)
 534 #endif
 535 #ifndef DBGERR
 536 #define DBGERR(fmt)
 537 #endif
 538 #ifndef DBGBH
 539 #define DBGBH(fmt)
 540 #endif
 541 #ifndef DBGISR
 542 #define DBGISR(fmt)
 543 #endif
 544
 545 #ifdef DBGDATA
 546 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 547 {
 548         int i;
 549         int linecount;
 550         printk("%s %s data:\n",info->device_name, label);
 551         while(count) {
 552                 linecount = (count > 16) ? 16 : count;
 553                 for(i=0; i < linecount; i++)
 554                         printk("%02X ",(unsigned char)data[i]);
 555                 for(;i<17;i++)
 556                         printk("   ");
 557                 for(i=0;i<linecount;i++) {
 558                         if (data[i]>=040 && data[i]<=0176)
 559                                 printk("%c",data[i]);
 560                         else
 561                                 printk(".");
 562                 }
 563                 printk("\n");
 564                 data  += linecount;
 565                 count -= linecount;
 566         }
 567 }
 568 #else
 569 #define DBGDATA(info, buf, size, label)
 570 #endif
 571
 572 #ifdef DBGTBUF
 573 static void dump_tbufs(struct slgt_info *info)
 574 {
 575         int i;
 576         printk("tbuf_current=%d\n", info->tbuf_current);
 577         for (i=0 ; i < info->tbuf_count ; i++) {
 578                 printk("%d: count=%04X status=%04X\n",
 579                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 580         }
 581 }
 582 #else
 583 #define DBGTBUF(info)
 584 #endif
 585
 586 #ifdef DBGRBUF
 587 static void dump_rbufs(struct slgt_info *info)
 588 {
 589         int i;
 590         printk("rbuf_current=%d\n", info->rbuf_current);
 591         for (i=0 ; i < info->rbuf_count ; i++) {
 592                 printk("%d: count=%04X status=%04X\n",
 593                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 594         }
 595 }
 596 #else
 597 #define DBGRBUF(info)
 598 #endif
 599
 600 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 601 {
 602 #ifdef SANITY_CHECK
 603         if (!info) {
 604                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 605                 return 1;
 606         }
 607         if (info->magic != MGSL_MAGIC) {
 608                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 609                 return 1;
 610         }
 611 #else
 612         if (!info)
 613                 return 1;
 614 #endif
 615         return 0;
 616 }
 617
 618 /**
 619  * line discipline callback wrappers
 620  *
 621  * The wrappers maintain line discipline references
 622  * while calling into the line discipline.
 623  *
 624  * ldisc_receive_buf  - pass receive data to line discipline
 625  */
 626 static void ldisc_receive_buf(struct tty_struct *tty,
 627                               const __u8 *data, char *flags, int count)
 628 {
 629         struct tty_ldisc *ld;
 630         if (!tty)
 631                 return;
 632         ld = tty_ldisc_ref(tty);
 633         if (ld) {
 634                 if (ld->ops->receive_buf)
 635                         ld->ops->receive_buf(tty, data, flags, count);
 636                 tty_ldisc_deref(ld);
 637         }
 638 }
 639
 640 /* tty callbacks */
 641
 642 static int open(struct tty_struct *tty, struct file *filp)
 643 {
 644         struct slgt_info *info;
 645         int retval, line;
 646         unsigned long flags;
 647
 648         line = tty->index;
 649         if ((line < 0) || (line >= slgt_device_count)) {
 650                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 651                 return -ENODEV;
 652         }
 653
 654         info = slgt_device_list;
 655         while(info && info->line != line)
 656                 info = info->next_device;
 657         if (sanity_check(info, tty->name, "open"))
 658                 return -ENODEV;
 659         if (info->init_error) {
 660                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 661                 return -ENODEV;
 662         }
 663
 664         tty->driver_data = info;
 665         info->port.tty = tty;
 666
 667         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
 668
 669         /* If port is closing, signal caller to try again */
 670         if (tty_hung_up_p(filp) || info->port.flags & ASYNC_CLOSING){
 671                 if (info->port.flags & ASYNC_CLOSING)
 672                         interruptible_sleep_on(&info->port.close_wait);
 673                 retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
 674                         -EAGAIN : -ERESTARTSYS);
 675                 goto cleanup;
 676         }
 677
 678         info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 679
 680         spin_lock_irqsave(&info->netlock, flags);
 681         if (info->netcount) {
 682                 retval = -EBUSY;
 683                 spin_unlock_irqrestore(&info->netlock, flags);
 684                 goto cleanup;
 685         }
 686         info->port.count++;
 687         spin_unlock_irqrestore(&info->netlock, flags);
 688
 689         if (info->port.count == 1) {
 690                 /* 1st open on this device, init hardware */
 691                 retval = startup(info);
 692                 if (retval < 0)
 693                         goto cleanup;
 694         }
 695
 696         retval = block_til_ready(tty, filp, info);
 697         if (retval) {
 698                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 699                 goto cleanup;
 700         }
 701
 702         retval = 0;
 703
 704 cleanup:
 705         if (retval) {
 706                 if (tty->count == 1)
 707                         info->port.tty = NULL; /* tty layer will release tty struct */
 708                 if(info->port.count)
 709                         info->port.count--;
 710         }
 711
 712         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 713         return retval;
 714 }
 715
 716 static void close(struct tty_struct *tty, struct file *filp)
 717 {
 718         struct slgt_info *info = tty->driver_data;
 719
 720         if (sanity_check(info, tty->name, "close"))
 721                 return;
 722         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
 723
 724         if (!info->port.count)
 725                 return;
 726
 727         if (tty_hung_up_p(filp))
 728                 goto cleanup;
 729
 730         if ((tty->count == 1) && (info->port.count != 1)) {
 731                 /*
 732                  * tty->count is 1 and the tty structure will be freed.
 733                  * info->port.count should be one in this case.
 734                  * if it's not, correct it so that the port is shutdown.
 735                  */
 736                 DBGERR(("%s close: bad refcount; tty->count=1, "
 737                        "info->port.count=%d\n", info->device_name, info->port.count));
 738                 info->port.count = 1;
 739         }
 740
 741         info->port.count--;
 742
 743         /* if at least one open remaining, leave hardware active */
 744         if (info->port.count)
 745                 goto cleanup;
 746
 747         info->port.flags |= ASYNC_CLOSING;
 748
 749         /* set tty->closing to notify line discipline to
 750          * only process XON/XOFF characters. Only the N_TTY
 751          * discipline appears to use this (ppp does not).
 752          */
 753         tty->closing = 1;
 754
 755         /* wait for transmit data to clear all layers */
 756
 757         if (info->port.closing_wait != ASYNC_CLOSING_WAIT_NONE) {
 758                 DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
 759                 tty_wait_until_sent(tty, info->port.closing_wait);
 760         }
 761
 762         if (info->port.flags & ASYNC_INITIALIZED)
 763                 wait_until_sent(tty, info->timeout);
 764         flush_buffer(tty);
 765         tty_ldisc_flush(tty);
 766
 767         shutdown(info);
 768
 769         tty->closing = 0;
 770         info->port.tty = NULL;
 771
 772         if (info->port.blocked_open) {
 773                 if (info->port.close_delay) {
 774                         msleep_interruptible(jiffies_to_msecs(info->port.close_delay));
 775                 }
 776                 wake_up_interruptible(&info->port.open_wait);
 777         }
 778
 779         info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
 780
 781         wake_up_interruptible(&info->port.close_wait);
 782
 783 cleanup:
 784         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
 785 }
 786
 787 static void hangup(struct tty_struct *tty)
 788 {
 789         struct slgt_info *info = tty->driver_data;
 790
 791         if (sanity_check(info, tty->name, "hangup"))
 792                 return;
 793         DBGINFO(("%s hangup\n", info->device_name));
 794
 795         flush_buffer(tty);
 796         shutdown(info);
 797
 798         info->port.count = 0;
 799         info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
 800         info->port.tty = NULL;
 801
 802         wake_up_interruptible(&info->port.open_wait);
 803 }
 804
 805 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 806 {
 807         struct slgt_info *info = tty->driver_data;
 808         unsigned long flags;
 809
 810         DBGINFO(("%s set_termios\n", tty->driver->name));
 811
 812         change_params(info);
 813
 814         /* Handle transition to B0 status */
 815         if (old_termios->c_cflag & CBAUD &&
 816             !(tty->termios->c_cflag & CBAUD)) {
 817                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 818                 spin_lock_irqsave(&info->lock,flags);
 819                 set_signals(info);
 820                 spin_unlock_irqrestore(&info->lock,flags);
 821         }
 822
 823         /* Handle transition away from B0 status */
 824         if (!(old_termios->c_cflag & CBAUD) &&
 825             tty->termios->c_cflag & CBAUD) {
 826                 info->signals |= SerialSignal_DTR;
 827                 if (!(tty->termios->c_cflag & CRTSCTS) ||
 828                     !test_bit(TTY_THROTTLED, &tty->flags)) {
 829                         info->signals |= SerialSignal_RTS;
 830                 }
 831                 spin_lock_irqsave(&info->lock,flags);
 832                 set_signals(info);
 833                 spin_unlock_irqrestore(&info->lock,flags);
 834         }
 835
 836         /* Handle turning off CRTSCTS */
 837         if (old_termios->c_cflag & CRTSCTS &&
 838             !(tty->termios->c_cflag & CRTSCTS)) {
 839                 tty->hw_stopped = 0;
 840                 tx_release(tty);
 841         }
 842 }
 843
 844 static int write(struct tty_struct *tty,
 845                  const unsigned char *buf, int count)
 846 {
 847         int ret = 0;
 848         struct slgt_info *info = tty->driver_data;
 849         unsigned long flags;
 850         unsigned int bufs_needed;
 851
 852         if (sanity_check(info, tty->name, "write"))
 853                 goto cleanup;
 854         DBGINFO(("%s write count=%d\n", info->device_name, count));
 855
 856         if (!info->tx_buf)
 857                 goto cleanup;
 858
 859         if (count > info->max_frame_size) {
 860                 ret = -EIO;
 861                 goto cleanup;
 862         }
 863
 864         if (!count)
 865                 goto cleanup;
 866
 867         if (!info->tx_active && info->tx_count) {
 868                 /* send accumulated data from send_char() */
 869                 tx_load(info, info->tx_buf, info->tx_count);
 870                 goto start;
 871         }
 872         bufs_needed = (count/DMABUFSIZE);
 873         if (count % DMABUFSIZE)
 874                 ++bufs_needed;
 875         if (bufs_needed > free_tbuf_count(info))
 876                 goto cleanup;
 877
 878         ret = info->tx_count = count;
 879         tx_load(info, buf, count);
 880         goto start;
 881
 882 start:
 883         if (info->tx_count && !tty->stopped && !tty->hw_stopped) {
 884                 spin_lock_irqsave(&info->lock,flags);
 885                 if (!info->tx_active)
 886                         tx_start(info);
 887                 else
 888                         tdma_start(info);
 889                 spin_unlock_irqrestore(&info->lock,flags);
 890         }
 891
 892 cleanup:
 893         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 894         return ret;
 895 }
 896
 897 static int put_char(struct tty_struct *tty, unsigned char ch)
 898 {
 899         struct slgt_info *info = tty->driver_data;
 900         unsigned long flags;
 901         int ret = 0;
 902
 903         if (sanity_check(info, tty->name, "put_char"))
 904                 return 0;
 905         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 906         if (!info->tx_buf)
 907                 return 0;
 908         spin_lock_irqsave(&info->lock,flags);
 909         if (!info->tx_active && (info->tx_count < info->max_frame_size)) {
 910                 info->tx_buf[info->tx_count++] = ch;
 911                 ret = 1;
 912         }
 913         spin_unlock_irqrestore(&info->lock,flags);
 914         return ret;
 915 }
 916
 917 static void send_xchar(struct tty_struct *tty, char ch)
 918 {
 919         struct slgt_info *info = tty->driver_data;
 920         unsigned long flags;
 921
 922         if (sanity_check(info, tty->name, "send_xchar"))
 923                 return;
 924         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 925         info->x_char = ch;
 926         if (ch) {
 927                 spin_lock_irqsave(&info->lock,flags);
 928                 if (!info->tx_enabled)
 929                         tx_start(info);
 930                 spin_unlock_irqrestore(&info->lock,flags);
 931         }
 932 }
 933
 934 static void wait_until_sent(struct tty_struct *tty, int timeout)
 935 {
 936         struct slgt_info *info = tty->driver_data;
 937         unsigned long orig_jiffies, char_time;
 938
 939         if (!info )
 940                 return;
 941         if (sanity_check(info, tty->name, "wait_until_sent"))
 942                 return;
 943         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 944         if (!(info->port.flags & ASYNC_INITIALIZED))
 945                 goto exit;
 946
 947         orig_jiffies = jiffies;
 948
 949         /* Set check interval to 1/5 of estimated time to
 950          * send a character, and make it at least 1. The check
 951          * interval should also be less than the timeout.
 952          * Note: use tight timings here to satisfy the NIST-PCTS.
 953          */
 954
 955         lock_kernel();
 956
 957         if (info->params.data_rate) {
 958                 char_time = info->timeout/(32 * 5);
 959                 if (!char_time)
 960                         char_time++;
 961         } else
 962                 char_time = 1;
 963
 964         if (timeout)
 965                 char_time = min_t(unsigned long, char_time, timeout);
 966
 967         while (info->tx_active) {
 968                 msleep_interruptible(jiffies_to_msecs(char_time));
 969                 if (signal_pending(current))
 970                         break;
 971                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 972                         break;
 973         }
 974         unlock_kernel();
 975
 976 exit:
 977         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 978 }
 979
 980 static int write_room(struct tty_struct *tty)
 981 {
 982         struct slgt_info *info = tty->driver_data;
 983         int ret;
 984
 985         if (sanity_check(info, tty->name, "write_room"))
 986                 return 0;
 987         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
 988         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
 989         return ret;
 990 }
 991
 992 static void flush_chars(struct tty_struct *tty)
 993 {
 994         struct slgt_info *info = tty->driver_data;
 995         unsigned long flags;
 996
 997         if (sanity_check(info, tty->name, "flush_chars"))
 998                 return;
 999         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
1000
1001         if (info->tx_count <= 0 || tty->stopped ||
1002             tty->hw_stopped || !info->tx_buf)
1003                 return;
1004
1005         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
1006
1007         spin_lock_irqsave(&info->lock,flags);
1008         if (!info->tx_active && info->tx_count) {
1009                 tx_load(info, info->tx_buf,info->tx_count);
1010                 tx_start(info);
1011         }
1012         spin_unlock_irqrestore(&info->lock,flags);
1013 }
1014
1015 static void flush_buffer(struct tty_struct *tty)
1016 {
1017         struct slgt_info *info = tty->driver_data;
1018         unsigned long flags;
1019
1020         if (sanity_check(info, tty->name, "flush_buffer"))
1021                 return;
1022         DBGINFO(("%s flush_buffer\n", info->device_name));
1023
1024         spin_lock_irqsave(&info->lock,flags);
1025         if (!info->tx_active)
1026                 info->tx_count = 0;
1027         spin_unlock_irqrestore(&info->lock,flags);
1028
1029         tty_wakeup(tty);
1030 }
1031
1032 /*
1033  * throttle (stop) transmitter
1034  */
1035 static void tx_hold(struct tty_struct *tty)
1036 {
1037         struct slgt_info *info = tty->driver_data;
1038         unsigned long flags;
1039
1040         if (sanity_check(info, tty->name, "tx_hold"))
1041                 return;
1042         DBGINFO(("%s tx_hold\n", info->device_name));
1043         spin_lock_irqsave(&info->lock,flags);
1044         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1045                 tx_stop(info);
1046         spin_unlock_irqrestore(&info->lock,flags);
1047 }
1048
1049 /*
1050  * release (start) transmitter
1051  */
1052 static void tx_release(struct tty_struct *tty)
1053 {
1054         struct slgt_info *info = tty->driver_data;
1055         unsigned long flags;
1056
1057         if (sanity_check(info, tty->name, "tx_release"))
1058                 return;
1059         DBGINFO(("%s tx_release\n", info->device_name));
1060         spin_lock_irqsave(&info->lock,flags);
1061         if (!info->tx_active && info->tx_count) {
1062                 tx_load(info, info->tx_buf, info->tx_count);
1063                 tx_start(info);
1064         }
1065         spin_unlock_irqrestore(&info->lock,flags);
1066 }
1067
1068 /*
1069  * Service an IOCTL request
1070  *
1071  * Arguments
1072  *
1073  *      tty     pointer to tty instance data
1074  *      file    pointer to associated file object for device
1075  *      cmd     IOCTL command code
1076  *      arg     command argument/context
1077  *
1078  * Return 0 if success, otherwise error code
1079  */
1080 static int ioctl(struct tty_struct *tty, struct file *file,
1081                  unsigned int cmd, unsigned long arg)
1082 {
1083         struct slgt_info *info = tty->driver_data;
1084         struct mgsl_icount cnow;        /* kernel counter temps */
1085         struct serial_icounter_struct __user *p_cuser;  /* user space */
1086         unsigned long flags;
1087         void __user *argp = (void __user *)arg;
1088         int ret;
1089
1090         if (sanity_check(info, tty->name, "ioctl"))
1091                 return -ENODEV;
1092         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1093
1094         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1095             (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
1096                 if (tty->flags & (1 << TTY_IO_ERROR))
1097                     return -EIO;
1098         }
1099
1100         lock_kernel();
1101
1102         switch (cmd) {
1103         case MGSL_IOCGPARAMS:
1104                 ret = get_params(info, argp);
1105                 break;
1106         case MGSL_IOCSPARAMS:
1107                 ret = set_params(info, argp);
1108                 break;
1109         case MGSL_IOCGTXIDLE:
1110                 ret = get_txidle(info, argp);
1111                 break;
1112         case MGSL_IOCSTXIDLE:
1113                 ret = set_txidle(info, (int)arg);
1114                 break;
1115         case MGSL_IOCTXENABLE:
1116                 ret = tx_enable(info, (int)arg);
1117                 break;
1118         case MGSL_IOCRXENABLE:
1119                 ret = rx_enable(info, (int)arg);
1120                 break;
1121         case MGSL_IOCTXABORT:
1122                 ret = tx_abort(info);
1123                 break;
1124         case MGSL_IOCGSTATS:
1125                 ret = get_stats(info, argp);
1126                 break;
1127         case MGSL_IOCWAITEVENT:
1128                 ret = wait_mgsl_event(info, argp);
1129                 break;
1130         case TIOCMIWAIT:
1131                 ret = modem_input_wait(info,(int)arg);
1132                 break;
1133         case MGSL_IOCGIF:
1134                 ret = get_interface(info, argp);
1135                 break;
1136         case MGSL_IOCSIF:
1137                 ret = set_interface(info,(int)arg);
1138                 break;
1139         case MGSL_IOCSGPIO:
1140                 ret = set_gpio(info, argp);
1141                 break;
1142         case MGSL_IOCGGPIO:
1143                 ret = get_gpio(info, argp);
1144                 break;
1145         case MGSL_IOCWAITGPIO:
1146                 ret = wait_gpio(info, argp);
1147                 break;
1148         case TIOCGICOUNT:
1149                 spin_lock_irqsave(&info->lock,flags);
1150                 cnow = info->icount;
1151                 spin_unlock_irqrestore(&info->lock,flags);
1152                 p_cuser = argp;
1153                 if (put_user(cnow.cts, &p_cuser->cts) ||
1154                     put_user(cnow.dsr, &p_cuser->dsr) ||
1155                     put_user(cnow.rng, &p_cuser->rng) ||
1156                     put_user(cnow.dcd, &p_cuser->dcd) ||
1157                     put_user(cnow.rx, &p_cuser->rx) ||
1158                     put_user(cnow.tx, &p_cuser->tx) ||
1159                     put_user(cnow.frame, &p_cuser->frame) ||
1160                     put_user(cnow.overrun, &p_cuser->overrun) ||
1161                     put_user(cnow.parity, &p_cuser->parity) ||
1162                     put_user(cnow.brk, &p_cuser->brk) ||
1163                     put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
1164                         ret = -EFAULT;
1165                 ret = 0;
1166                 break;
1167         default:
1168                 ret = -ENOIOCTLCMD;
1169         }
1170         unlock_kernel();
1171         return ret;
1172 }
1173
1174 /*
1175  * support for 32 bit ioctl calls on 64 bit systems
1176  */
1177 #ifdef CONFIG_COMPAT
1178 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1179 {
1180         struct MGSL_PARAMS32 tmp_params;
1181
1182         DBGINFO(("%s get_params32\n", info->device_name));
1183         tmp_params.mode            = (compat_ulong_t)info->params.mode;
1184         tmp_params.loopback        = info->params.loopback;
1185         tmp_params.flags           = info->params.flags;
1186         tmp_params.encoding        = info->params.encoding;
1187         tmp_params.clock_speed     = (compat_ulong_t)info->params.clock_speed;
1188         tmp_params.addr_filter     = info->params.addr_filter;
1189         tmp_params.crc_type        = info->params.crc_type;
1190         tmp_params.preamble_length = info->params.preamble_length;
1191         tmp_params.preamble        = info->params.preamble;
1192         tmp_params.data_rate       = (compat_ulong_t)info->params.data_rate;
1193         tmp_params.data_bits       = info->params.data_bits;
1194         tmp_params.stop_bits       = info->params.stop_bits;
1195         tmp_params.parity          = info->params.parity;
1196         if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1197                 return -EFAULT;
1198         return 0;
1199 }
1200
1201 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1202 {
1203         struct MGSL_PARAMS32 tmp_params;
1204
1205         DBGINFO(("%s set_params32\n", info->device_name));
1206         if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1207                 return -EFAULT;
1208
1209         spin_lock(&info->lock);
1210         info->params.mode            = tmp_params.mode;
1211         info->params.loopback        = tmp_params.loopback;
1212         info->params.flags           = tmp_params.flags;
1213         info->params.encoding        = tmp_params.encoding;
1214         info->params.clock_speed     = tmp_params.clock_speed;
1215         info->params.addr_filter     = tmp_params.addr_filter;
1216         info->params.crc_type        = tmp_params.crc_type;
1217         info->params.preamble_length = tmp_params.preamble_length;
1218         info->params.preamble        = tmp_params.preamble;
1219         info->params.data_rate       = tmp_params.data_rate;
1220         info->params.data_bits       = tmp_params.data_bits;
1221         info->params.stop_bits       = tmp_params.stop_bits;
1222         info->params.parity          = tmp_params.parity;
1223         spin_unlock(&info->lock);
1224
1225         change_params(info);
1226
1227         return 0;
1228 }
1229
1230 static long slgt_compat_ioctl(struct tty_struct *tty, struct file *file,
1231                          unsigned int cmd, unsigned long arg)
1232 {
1233         struct slgt_info *info = tty->driver_data;
1234         int rc = -ENOIOCTLCMD;
1235
1236         if (sanity_check(info, tty->name, "compat_ioctl"))
1237                 return -ENODEV;
1238         DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1239
1240         switch (cmd) {
1241
1242         case MGSL_IOCSPARAMS32:
1243                 rc = set_params32(info, compat_ptr(arg));
1244                 break;
1245
1246         case MGSL_IOCGPARAMS32:
1247                 rc = get_params32(info, compat_ptr(arg));
1248                 break;
1249
1250         case MGSL_IOCGPARAMS:
1251         case MGSL_IOCSPARAMS:
1252         case MGSL_IOCGTXIDLE:
1253         case MGSL_IOCGSTATS:
1254         case MGSL_IOCWAITEVENT:
1255         case MGSL_IOCGIF:
1256         case MGSL_IOCSGPIO:
1257         case MGSL_IOCGGPIO:
1258         case MGSL_IOCWAITGPIO:
1259         case TIOCGICOUNT:
1260                 rc = ioctl(tty, file, cmd, (unsigned long)(compat_ptr(arg)));
1261                 break;
1262
1263         case MGSL_IOCSTXIDLE:
1264         case MGSL_IOCTXENABLE:
1265         case MGSL_IOCRXENABLE:
1266         case MGSL_IOCTXABORT:
1267         case TIOCMIWAIT:
1268         case MGSL_IOCSIF:
1269                 rc = ioctl(tty, file, cmd, arg);
1270                 break;
1271         }
1272
1273         DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1274         return rc;
1275 }
1276 #else
1277 #define slgt_compat_ioctl NULL
1278 #endif /* ifdef CONFIG_COMPAT */
1279
1280 /*
1281  * proc fs support
1282  */
1283 static inline int line_info(char *buf, struct slgt_info *info)
1284 {
1285         char stat_buf[30];
1286         int ret;
1287         unsigned long flags;
1288
1289         ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1290                       info->device_name, info->phys_reg_addr,
1291                       info->irq_level, info->max_frame_size);
1292
1293         /* output current serial signal states */
1294         spin_lock_irqsave(&info->lock,flags);
1295         get_signals(info);
1296         spin_unlock_irqrestore(&info->lock,flags);
1297
1298         stat_buf[0] = 0;
1299         stat_buf[1] = 0;
1300         if (info->signals & SerialSignal_RTS)
1301                 strcat(stat_buf, "|RTS");
1302         if (info->signals & SerialSignal_CTS)
1303                 strcat(stat_buf, "|CTS");
1304         if (info->signals & SerialSignal_DTR)
1305                 strcat(stat_buf, "|DTR");
1306         if (info->signals & SerialSignal_DSR)
1307                 strcat(stat_buf, "|DSR");
1308         if (info->signals & SerialSignal_DCD)
1309                 strcat(stat_buf, "|CD");
1310         if (info->signals & SerialSignal_RI)
1311                 strcat(stat_buf, "|RI");
1312
1313         if (info->params.mode != MGSL_MODE_ASYNC) {
1314                 ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
1315                                info->icount.txok, info->icount.rxok);
1316                 if (info->icount.txunder)
1317                         ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
1318                 if (info->icount.txabort)
1319                         ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
1320                 if (info->icount.rxshort)
1321                         ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
1322                 if (info->icount.rxlong)
1323                         ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
1324                 if (info->icount.rxover)
1325                         ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
1326                 if (info->icount.rxcrc)
1327                         ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
1328         } else {
1329                 ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
1330                                info->icount.tx, info->icount.rx);
1331                 if (info->icount.frame)
1332                         ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
1333                 if (info->icount.parity)
1334                         ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
1335                 if (info->icount.brk)
1336                         ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
1337                 if (info->icount.overrun)
1338                         ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
1339         }
1340
1341         /* Append serial signal status to end */
1342         ret += sprintf(buf+ret, " %s\n", stat_buf+1);
1343
1344         ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1345                        info->tx_active,info->bh_requested,info->bh_running,
1346                        info->pending_bh);
1347
1348         return ret;
1349 }
1350
1351 /* Called to print information about devices
1352  */
1353 static int read_proc(char *page, char **start, off_t off, int count,
1354                      int *eof, void *data)
1355 {
1356         int len = 0, l;
1357         off_t   begin = 0;
1358         struct slgt_info *info;
1359
1360         len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
1361
1362         info = slgt_device_list;
1363         while( info ) {
1364                 l = line_info(page + len, info);
1365                 len += l;
1366                 if (len+begin > off+count)
1367                         goto done;
1368                 if (len+begin < off) {
1369                         begin += len;
1370                         len = 0;
1371                 }
1372                 info = info->next_device;
1373         }
1374
1375         *eof = 1;
1376 done:
1377         if (off >= len+begin)
1378                 return 0;
1379         *start = page + (off-begin);
1380         return ((count < begin+len-off) ? count : begin+len-off);
1381 }
1382
1383 /*
1384  * return count of bytes in transmit buffer
1385  */
1386 static int chars_in_buffer(struct tty_struct *tty)
1387 {
1388         struct slgt_info *info = tty->driver_data;
1389         int count;
1390         if (sanity_check(info, tty->name, "chars_in_buffer"))
1391                 return 0;
1392         count = tbuf_bytes(info);
1393         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1394         return count;
1395 }
1396
1397 /*
1398  * signal remote device to throttle send data (our receive data)
1399  */
1400 static void throttle(struct tty_struct * tty)
1401 {
1402         struct slgt_info *info = tty->driver_data;
1403         unsigned long flags;
1404
1405         if (sanity_check(info, tty->name, "throttle"))
1406                 return;
1407         DBGINFO(("%s throttle\n", info->device_name));
1408         if (I_IXOFF(tty))
1409                 send_xchar(tty, STOP_CHAR(tty));
1410         if (tty->termios->c_cflag & CRTSCTS) {
1411                 spin_lock_irqsave(&info->lock,flags);
1412                 info->signals &= ~SerialSignal_RTS;
1413                 set_signals(info);
1414                 spin_unlock_irqrestore(&info->lock,flags);
1415         }
1416 }
1417
1418 /*
1419  * signal remote device to stop throttling send data (our receive data)
1420  */
1421 static void unthrottle(struct tty_struct * tty)
1422 {
1423         struct slgt_info *info = tty->driver_data;
1424         unsigned long flags;
1425
1426         if (sanity_check(info, tty->name, "unthrottle"))
1427                 return;
1428         DBGINFO(("%s unthrottle\n", info->device_name));
1429         if (I_IXOFF(tty)) {
1430                 if (info->x_char)
1431                         info->x_char = 0;
1432                 else
1433                         send_xchar(tty, START_CHAR(tty));
1434         }
1435         if (tty->termios->c_cflag & CRTSCTS) {
1436                 spin_lock_irqsave(&info->lock,flags);
1437                 info->signals |= SerialSignal_RTS;
1438                 set_signals(info);
1439                 spin_unlock_irqrestore(&info->lock,flags);
1440         }
1441 }
1442
1443 /*
1444  * set or clear transmit break condition
1445  * break_state  -1=set break condition, 0=clear
1446  */
1447 static int set_break(struct tty_struct *tty, int break_state)
1448 {
1449         struct slgt_info *info = tty->driver_data;
1450         unsigned short value;
1451         unsigned long flags;
1452
1453         if (sanity_check(info, tty->name, "set_break"))
1454                 return -EINVAL;
1455         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1456
1457         spin_lock_irqsave(&info->lock,flags);
1458         value = rd_reg16(info, TCR);
1459         if (break_state == -1)
1460                 value |= BIT6;
1461         else
1462                 value &= ~BIT6;
1463         wr_reg16(info, TCR, value);
1464         spin_unlock_irqrestore(&info->lock,flags);
1465         return 0;
1466 }
1467
1468 #if SYNCLINK_GENERIC_HDLC
1469
1470 /**
1471  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1472  * set encoding and frame check sequence (FCS) options
1473  *
1474  * dev       pointer to network device structure
1475  * encoding  serial encoding setting
1476  * parity    FCS setting
1477  *
1478  * returns 0 if success, otherwise error code
1479  */
1480 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1481                           unsigned short parity)
1482 {
1483         struct slgt_info *info = dev_to_port(dev);
1484         unsigned char  new_encoding;
1485         unsigned short new_crctype;
1486
1487         /* return error if TTY interface open */
1488         if (info->port.count)
1489                 return -EBUSY;
1490
1491         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1492
1493         switch (encoding)
1494         {
1495         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1496         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1497         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1498         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1499         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1500         default: return -EINVAL;
1501         }
1502
1503         switch (parity)
1504         {
1505         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1506         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1507         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1508         default: return -EINVAL;
1509         }
1510
1511         info->params.encoding = new_encoding;
1512         info->params.crc_type = new_crctype;
1513
1514         /* if network interface up, reprogram hardware */
1515         if (info->netcount)
1516                 program_hw(info);
1517
1518         return 0;
1519 }
1520
1521 /**
1522  * called by generic HDLC layer to send frame
1523  *
1524  * skb  socket buffer containing HDLC frame
1525  * dev  pointer to network device structure
1526  *
1527  * returns 0 if success, otherwise error code
1528  */
1529 static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
1530 {
1531         struct slgt_info *info = dev_to_port(dev);
1532         unsigned long flags;
1533
1534         DBGINFO(("%s hdlc_xmit\n", dev->name));
1535
1536         /* stop sending until this frame completes */
1537         netif_stop_queue(dev);
1538
1539         /* copy data to device buffers */
1540         info->tx_count = skb->len;
1541         tx_load(info, skb->data, skb->len);
1542
1543         /* update network statistics */
1544         dev->stats.tx_packets++;
1545         dev->stats.tx_bytes += skb->len;
1546
1547         /* done with socket buffer, so free it */
1548         dev_kfree_skb(skb);
1549
1550         /* save start time for transmit timeout detection */
1551         dev->trans_start = jiffies;
1552
1553         /* start hardware transmitter if necessary */
1554         spin_lock_irqsave(&info->lock,flags);
1555         if (!info->tx_active)
1556                 tx_start(info);
1557         spin_unlock_irqrestore(&info->lock,flags);
1558
1559         return 0;
1560 }
1561
1562 /**
1563  * called by network layer when interface enabled
1564  * claim resources and initialize hardware
1565  *
1566  * dev  pointer to network device structure
1567  *
1568  * returns 0 if success, otherwise error code
1569  */
1570 static int hdlcdev_open(struct net_device *dev)
1571 {
1572         struct slgt_info *info = dev_to_port(dev);
1573         int rc;
1574         unsigned long flags;
1575
1576         if (!try_module_get(THIS_MODULE))
1577                 return -EBUSY;
1578
1579         DBGINFO(("%s hdlcdev_open\n", dev->name));
1580
1581         /* generic HDLC layer open processing */
1582         if ((rc = hdlc_open(dev)))
1583                 return rc;
1584
1585         /* arbitrate between network and tty opens */
1586         spin_lock_irqsave(&info->netlock, flags);
1587         if (info->port.count != 0 || info->netcount != 0) {
1588                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1589                 spin_unlock_irqrestore(&info->netlock, flags);
1590                 return -EBUSY;
1591         }
1592         info->netcount=1;
1593         spin_unlock_irqrestore(&info->netlock, flags);
1594
1595         /* claim resources and init adapter */
1596         if ((rc = startup(info)) != 0) {
1597                 spin_lock_irqsave(&info->netlock, flags);
1598                 info->netcount=0;
1599                 spin_unlock_irqrestore(&info->netlock, flags);
1600                 return rc;
1601         }
1602
1603         /* assert DTR and RTS, apply hardware settings */
1604         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1605         program_hw(info);
1606
1607         /* enable network layer transmit */
1608         dev->trans_start = jiffies;
1609         netif_start_queue(dev);
1610
1611         /* inform generic HDLC layer of current DCD status */
1612         spin_lock_irqsave(&info->lock, flags);
1613         get_signals(info);
1614         spin_unlock_irqrestore(&info->lock, flags);
1615         if (info->signals & SerialSignal_DCD)
1616                 netif_carrier_on(dev);
1617         else
1618                 netif_carrier_off(dev);
1619         return 0;
1620 }
1621
1622 /**
1623  * called by network layer when interface is disabled
1624  * shutdown hardware and release resources
1625  *
1626  * dev  pointer to network device structure
1627  *
1628  * returns 0 if success, otherwise error code
1629  */
1630 static int hdlcdev_close(struct net_device *dev)
1631 {
1632         struct slgt_info *info = dev_to_port(dev);
1633         unsigned long flags;
1634
1635         DBGINFO(("%s hdlcdev_close\n", dev->name));
1636
1637         netif_stop_queue(dev);
1638
1639         /* shutdown adapter and release resources */
1640         shutdown(info);
1641
1642         hdlc_close(dev);
1643
1644         spin_lock_irqsave(&info->netlock, flags);
1645         info->netcount=0;
1646         spin_unlock_irqrestore(&info->netlock, flags);
1647
1648         module_put(THIS_MODULE);
1649         return 0;
1650 }
1651
1652 /**
1653  * called by network layer to process IOCTL call to network device
1654  *
1655  * dev  pointer to network device structure
1656  * ifr  pointer to network interface request structure
1657  * cmd  IOCTL command code
1658  *
1659  * returns 0 if success, otherwise error code
1660  */
1661 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1662 {
1663         const size_t size = sizeof(sync_serial_settings);
1664         sync_serial_settings new_line;
1665         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1666         struct slgt_info *info = dev_to_port(dev);
1667         unsigned int flags;
1668
1669         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1670
1671         /* return error if TTY interface open */
1672         if (info->port.count)
1673                 return -EBUSY;
1674
1675         if (cmd != SIOCWANDEV)
1676                 return hdlc_ioctl(dev, ifr, cmd);
1677
1678         switch(ifr->ifr_settings.type) {
1679         case IF_GET_IFACE: /* return current sync_serial_settings */
1680
1681                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1682                 if (ifr->ifr_settings.size < size) {
1683                         ifr->ifr_settings.size = size; /* data size wanted */
1684                         return -ENOBUFS;
1685                 }
1686
1687                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1688                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1689                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1690                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1691
1692                 switch (flags){
1693                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1694                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1695                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1696                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1697                 default: new_line.clock_type = CLOCK_DEFAULT;
1698                 }
1699
1700                 new_line.clock_rate = info->params.clock_speed;
1701                 new_line.loopback   = info->params.loopback ? 1:0;
1702
1703                 if (copy_to_user(line, &new_line, size))
1704                         return -EFAULT;
1705                 return 0;
1706
1707         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1708
1709                 if(!capable(CAP_NET_ADMIN))
1710                         return -EPERM;
1711                 if (copy_from_user(&new_line, line, size))
1712                         return -EFAULT;
1713
1714                 switch (new_line.clock_type)
1715                 {
1716                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1717                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1718                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1719                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1720                 case CLOCK_DEFAULT:  flags = info->params.flags &
1721                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1722                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1723                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1724                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1725                 default: return -EINVAL;
1726                 }
1727
1728                 if (new_line.loopback != 0 && new_line.loopback != 1)
1729                         return -EINVAL;
1730
1731                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1732                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1733                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1734                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1735                 info->params.flags |= flags;
1736
1737                 info->params.loopback = new_line.loopback;
1738
1739                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1740                         info->params.clock_speed = new_line.clock_rate;
1741                 else
1742                         info->params.clock_speed = 0;
1743
1744                 /* if network interface up, reprogram hardware */
1745                 if (info->netcount)
1746                         program_hw(info);
1747                 return 0;
1748
1749         default:
1750                 return hdlc_ioctl(dev, ifr, cmd);
1751         }
1752 }
1753
1754 /**
1755  * called by network layer when transmit timeout is detected
1756  *
1757  * dev  pointer to network device structure
1758  */
1759 static void hdlcdev_tx_timeout(struct net_device *dev)
1760 {
1761         struct slgt_info *info = dev_to_port(dev);
1762         unsigned long flags;
1763
1764         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1765
1766         dev->stats.tx_errors++;
1767         dev->stats.tx_aborted_errors++;
1768
1769         spin_lock_irqsave(&info->lock,flags);
1770         tx_stop(info);
1771         spin_unlock_irqrestore(&info->lock,flags);
1772
1773         netif_wake_queue(dev);
1774 }
1775
1776 /**
1777  * called by device driver when transmit completes
1778  * reenable network layer transmit if stopped
1779  *
1780  * info  pointer to device instance information
1781  */
1782 static void hdlcdev_tx_done(struct slgt_info *info)
1783 {
1784         if (netif_queue_stopped(info->netdev))
1785                 netif_wake_queue(info->netdev);
1786 }
1787
1788 /**
1789  * called by device driver when frame received
1790  * pass frame to network layer
1791  *
1792  * info  pointer to device instance information
1793  * buf   pointer to buffer contianing frame data
1794  * size  count of data bytes in buf
1795  */
1796 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1797 {
1798         struct sk_buff *skb = dev_alloc_skb(size);
1799         struct net_device *dev = info->netdev;
1800
1801         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1802
1803         if (skb == NULL) {
1804                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1805                 dev->stats.rx_dropped++;
1806                 return;
1807         }
1808
1809         memcpy(skb_put(skb, size), buf, size);
1810
1811         skb->protocol = hdlc_type_trans(skb, dev);
1812
1813         dev->stats.rx_packets++;
1814         dev->stats.rx_bytes += size;
1815
1816         netif_rx(skb);
1817
1818         dev->last_rx = jiffies;
1819 }
1820
1821 /**
1822  * called by device driver when adding device instance
1823  * do generic HDLC initialization
1824  *
1825  * info  pointer to device instance information
1826  *
1827  * returns 0 if success, otherwise error code
1828  */
1829 static int hdlcdev_init(struct slgt_info *info)
1830 {
1831         int rc;
1832         struct net_device *dev;
1833         hdlc_device *hdlc;
1834
1835         /* allocate and initialize network and HDLC layer objects */
1836
1837         if (!(dev = alloc_hdlcdev(info))) {
1838                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1839                 return -ENOMEM;
1840         }
1841
1842         /* for network layer reporting purposes only */
1843         dev->mem_start = info->phys_reg_addr;
1844         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1845         dev->irq       = info->irq_level;
1846
1847         /* network layer callbacks and settings */
1848         dev->do_ioctl       = hdlcdev_ioctl;
1849         dev->open           = hdlcdev_open;
1850         dev->stop           = hdlcdev_close;
1851         dev->tx_timeout     = hdlcdev_tx_timeout;
1852         dev->watchdog_timeo = 10*HZ;
1853         dev->tx_queue_len   = 50;
1854
1855         /* generic HDLC layer callbacks and settings */
1856         hdlc         = dev_to_hdlc(dev);
1857         hdlc->attach = hdlcdev_attach;
1858         hdlc->xmit   = hdlcdev_xmit;
1859
1860         /* register objects with HDLC layer */
1861         if ((rc = register_hdlc_device(dev))) {
1862                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1863                 free_netdev(dev);
1864                 return rc;
1865         }
1866
1867         info->netdev = dev;
1868         return 0;
1869 }
1870
1871 /**
1872  * called by device driver when removing device instance
1873  * do generic HDLC cleanup
1874  *
1875  * info  pointer to device instance information
1876  */
1877 static void hdlcdev_exit(struct slgt_info *info)
1878 {
1879         unregister_hdlc_device(info->netdev);
1880         free_netdev(info->netdev);
1881         info->netdev = NULL;
1882 }
1883
1884 #endif /* ifdef CONFIG_HDLC */
1885
1886 /*
1887  * get async data from rx DMA buffers
1888  */
1889 static void rx_async(struct slgt_info *info)
1890 {
1891         struct tty_struct *tty = info->port.tty;
1892         struct mgsl_icount *icount = &info->icount;
1893         unsigned int start, end;
1894         unsigned char *p;
1895         unsigned char status;
1896         struct slgt_desc *bufs = info->rbufs;
1897         int i, count;
1898         int chars = 0;
1899         int stat;
1900         unsigned char ch;
1901
1902         start = end = info->rbuf_current;
1903
1904         while(desc_complete(bufs[end])) {
1905                 count = desc_count(bufs[end]) - info->rbuf_index;
1906                 p     = bufs[end].buf + info->rbuf_index;
1907
1908                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1909                 DBGDATA(info, p, count, "rx");
1910
1911                 for(i=0 ; i < count; i+=2, p+=2) {
1912                         ch = *p;
1913                         icount->rx++;
1914
1915                         stat = 0;
1916
1917                         if ((status = *(p+1) & (BIT1 + BIT0))) {
1918                                 if (status & BIT1)
1919                                         icount->parity++;
1920                                 else if (status & BIT0)
1921                                         icount->frame++;
1922                                 /* discard char if tty control flags say so */
1923                                 if (status & info->ignore_status_mask)
1924                                         continue;
1925                                 if (status & BIT1)
1926                                         stat = TTY_PARITY;
1927                                 else if (status & BIT0)
1928                                         stat = TTY_FRAME;
1929                         }
1930                         if (tty) {
1931                                 tty_insert_flip_char(tty, ch, stat);
1932                                 chars++;
1933                         }
1934                 }
1935
1936                 if (i < count) {
1937                         /* receive buffer not completed */
1938                         info->rbuf_index += i;
1939                         mod_timer(&info->rx_timer, jiffies + 1);
1940                         break;
1941                 }
1942
1943                 info->rbuf_index = 0;
1944                 free_rbufs(info, end, end);
1945
1946                 if (++end == info->rbuf_count)
1947                         end = 0;
1948
1949                 /* if entire list searched then no frame available */
1950                 if (end == start)
1951                         break;
1952         }
1953
1954         if (tty && chars)
1955                 tty_flip_buffer_push(tty);
1956 }
1957
1958 /*
1959  * return next bottom half action to perform
1960  */
1961 static int bh_action(struct slgt_info *info)
1962 {
1963         unsigned long flags;
1964         int rc;
1965
1966         spin_lock_irqsave(&info->lock,flags);
1967
1968         if (info->pending_bh & BH_RECEIVE) {
1969                 info->pending_bh &= ~BH_RECEIVE;
1970                 rc = BH_RECEIVE;
1971         } else if (info->pending_bh & BH_TRANSMIT) {
1972                 info->pending_bh &= ~BH_TRANSMIT;
1973                 rc = BH_TRANSMIT;
1974         } else if (info->pending_bh & BH_STATUS) {
1975                 info->pending_bh &= ~BH_STATUS;
1976                 rc = BH_STATUS;
1977         } else {
1978                 /* Mark BH routine as complete */
1979                 info->bh_running = false;
1980                 info->bh_requested = false;
1981                 rc = 0;
1982         }
1983
1984         spin_unlock_irqrestore(&info->lock,flags);
1985
1986         return rc;
1987 }
1988
1989 /*
1990  * perform bottom half processing
1991  */
1992 static void bh_handler(struct work_struct *work)
1993 {
1994         struct slgt_info *info = container_of(work, struct slgt_info, task);
1995         int action;
1996
1997         if (!info)
1998                 return;
1999         info->bh_running = true;
2000
2001         while((action = bh_action(info))) {
2002                 switch (action) {
2003                 case BH_RECEIVE:
2004                         DBGBH(("%s bh receive\n", info->device_name));
2005                         switch(info->params.mode) {
2006                         case MGSL_MODE_ASYNC:
2007                                 rx_async(info);
2008                                 break;
2009                         case MGSL_MODE_HDLC:
2010                                 while(rx_get_frame(info));
2011                                 break;
2012                         case MGSL_MODE_RAW:
2013                         case MGSL_MODE_MONOSYNC:
2014                         case MGSL_MODE_BISYNC:
2015                                 while(rx_get_buf(info));
2016                                 break;
2017                         }
2018                         /* restart receiver if rx DMA buffers exhausted */
2019                         if (info->rx_restart)
2020                                 rx_start(info);
2021                         break;
2022                 case BH_TRANSMIT:
2023                         bh_transmit(info);
2024                         break;
2025                 case BH_STATUS:
2026                         DBGBH(("%s bh status\n", info->device_name));
2027                         info->ri_chkcount = 0;
2028                         info->dsr_chkcount = 0;
2029                         info->dcd_chkcount = 0;
2030                         info->cts_chkcount = 0;
2031                         break;
2032                 default:
2033                         DBGBH(("%s unknown action\n", info->device_name));
2034                         break;
2035                 }
2036         }
2037         DBGBH(("%s bh_handler exit\n", info->device_name));
2038 }
2039
2040 static void bh_transmit(struct slgt_info *info)
2041 {
2042         struct tty_struct *tty = info->port.tty;
2043
2044         DBGBH(("%s bh_transmit\n", info->device_name));
2045         if (tty)
2046                 tty_wakeup(tty);
2047 }
2048
2049 static void dsr_change(struct slgt_info *info, unsigned short status)
2050 {
2051         if (status & BIT3) {
2052                 info->signals |= SerialSignal_DSR;
2053                 info->input_signal_events.dsr_up++;
2054         } else {
2055                 info->signals &= ~SerialSignal_DSR;
2056                 info->input_signal_events.dsr_down++;
2057         }
2058         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
2059         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2060                 slgt_irq_off(info, IRQ_DSR);
2061                 return;
2062         }
2063         info->icount.dsr++;
2064         wake_up_interruptible(&info->status_event_wait_q);
2065         wake_up_interruptible(&info->event_wait_q);
2066         info->pending_bh |= BH_STATUS;
2067 }
2068
2069 static void cts_change(struct slgt_info *info, unsigned short status)
2070 {
2071         if (status & BIT2) {
2072                 info->signals |= SerialSignal_CTS;
2073                 info->input_signal_events.cts_up++;
2074         } else {
2075                 info->signals &= ~SerialSignal_CTS;
2076                 info->input_signal_events.cts_down++;
2077         }
2078         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2079         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2080                 slgt_irq_off(info, IRQ_CTS);
2081                 return;
2082         }
2083         info->icount.cts++;
2084         wake_up_interruptible(&info->status_event_wait_q);
2085         wake_up_interruptible(&info->event_wait_q);
2086         info->pending_bh |= BH_STATUS;
2087
2088         if (info->port.flags & ASYNC_CTS_FLOW) {
2089                 if (info->port.tty) {
2090                         if (info->port.tty->hw_stopped) {
2091                                 if (info->signals & SerialSignal_CTS) {
2092                                         info->port.tty->hw_stopped = 0;
2093                                         info->pending_bh |= BH_TRANSMIT;
2094                                         return;
2095                                 }
2096                         } else {
2097                                 if (!(info->signals & SerialSignal_CTS))
2098                                         info->port.tty->hw_stopped = 1;
2099                         }
2100                 }
2101         }
2102 }
2103
2104 static void dcd_change(struct slgt_info *info, unsigned short status)
2105 {
2106         if (status & BIT1) {
2107                 info->signals |= SerialSignal_DCD;
2108                 info->input_signal_events.dcd_up++;
2109         } else {
2110                 info->signals &= ~SerialSignal_DCD;
2111                 info->input_signal_events.dcd_down++;
2112         }
2113         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2114         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2115                 slgt_irq_off(info, IRQ_DCD);
2116                 return;
2117         }
2118         info->icount.dcd++;
2119 #if SYNCLINK_GENERIC_HDLC
2120         if (info->netcount) {
2121                 if (info->signals & SerialSignal_DCD)
2122                         netif_carrier_on(info->netdev);
2123                 else
2124                         netif_carrier_off(info->netdev);
2125         }
2126 #endif
2127         wake_up_interruptible(&info->status_event_wait_q);
2128         wake_up_interruptible(&info->event_wait_q);
2129         info->pending_bh |= BH_STATUS;
2130
2131         if (info->port.flags & ASYNC_CHECK_CD) {
2132                 if (info->signals & SerialSignal_DCD)
2133                         wake_up_interruptible(&info->port.open_wait);
2134                 else {
2135                         if (info->port.tty)
2136                                 tty_hangup(info->port.tty);
2137                 }
2138         }
2139 }
2140
2141 static void ri_change(struct slgt_info *info, unsigned short status)
2142 {
2143         if (status & BIT0) {
2144                 info->signals |= SerialSignal_RI;
2145                 info->input_signal_events.ri_up++;
2146         } else {
2147                 info->signals &= ~SerialSignal_RI;
2148                 info->input_signal_events.ri_down++;
2149         }
2150         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2151         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2152                 slgt_irq_off(info, IRQ_RI);
2153                 return;
2154         }
2155         info->icount.rng++;
2156         wake_up_interruptible(&info->status_event_wait_q);
2157         wake_up_interruptible(&info->event_wait_q);
2158         info->pending_bh |= BH_STATUS;
2159 }
2160
2161 static void isr_serial(struct slgt_info *info)
2162 {
2163         unsigned short status = rd_reg16(info, SSR);
2164
2165         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2166
2167         wr_reg16(info, SSR, status); /* clear pending */
2168
2169         info->irq_occurred = true;
2170
2171         if (info->params.mode == MGSL_MODE_ASYNC) {
2172                 if (status & IRQ_TXIDLE) {
2173                         if (info->tx_count)
2174                                 isr_txeom(info, status);
2175                 }
2176                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2177                         info->icount.brk++;
2178                         /* process break detection if tty control allows */
2179                         if (info->port.tty) {
2180                                 if (!(status & info->ignore_status_mask)) {
2181                                         if (info->read_status_mask & MASK_BREAK) {
2182                                                 tty_insert_flip_char(info->port.tty, 0, TTY_BREAK);
2183                                                 if (info->port.flags & ASYNC_SAK)
2184                                                         do_SAK(info->port.tty);
2185                                         }
2186                                 }
2187                         }
2188                 }
2189         } else {
2190                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2191                         isr_txeom(info, status);
2192
2193                 if (status & IRQ_RXIDLE) {
2194                         if (status & RXIDLE)
2195                                 info->icount.rxidle++;
2196                         else
2197                                 info->icount.exithunt++;
2198                         wake_up_interruptible(&info->event_wait_q);
2199                 }
2200
2201                 if (status & IRQ_RXOVER)
2202                         rx_start(info);
2203         }
2204
2205         if (status & IRQ_DSR)
2206                 dsr_change(info, status);
2207         if (status & IRQ_CTS)
2208                 cts_change(info, status);
2209         if (status & IRQ_DCD)
2210                 dcd_change(info, status);
2211         if (status & IRQ_RI)
2212                 ri_change(info, status);
2213 }
2214
2215 static void isr_rdma(struct slgt_info *info)
2216 {
2217         unsigned int status = rd_reg32(info, RDCSR);
2218
2219         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2220
2221         /* RDCSR (rx DMA control/status)
2222          *
2223          * 31..07  reserved
2224          * 06      save status byte to DMA buffer
2225          * 05      error
2226          * 04      eol (end of list)
2227          * 03      eob (end of buffer)
2228          * 02      IRQ enable
2229          * 01      reset
2230          * 00      enable
2231          */
2232         wr_reg32(info, RDCSR, status);  /* clear pending */
2233
2234         if (status & (BIT5 + BIT4)) {
2235                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2236                 info->rx_restart = true;
2237         }
2238         info->pending_bh |= BH_RECEIVE;
2239 }
2240
2241 static void isr_tdma(struct slgt_info *info)
2242 {
2243         unsigned int status = rd_reg32(info, TDCSR);
2244
2245         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2246
2247         /* TDCSR (tx DMA control/status)
2248          *
2249          * 31..06  reserved
2250          * 05      error
2251          * 04      eol (end of list)
2252          * 03      eob (end of buffer)
2253          * 02      IRQ enable
2254          * 01      reset
2255          * 00      enable
2256          */
2257         wr_reg32(info, TDCSR, status);  /* clear pending */
2258
2259         if (status & (BIT5 + BIT4 + BIT3)) {
2260                 // another transmit buffer has completed
2261                 // run bottom half to get more send data from user
2262                 info->pending_bh |= BH_TRANSMIT;
2263         }
2264 }
2265
2266 static void isr_txeom(struct slgt_info *info, unsigned short status)
2267 {
2268         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2269
2270         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2271         tdma_reset(info);
2272         reset_tbufs(info);
2273         if (status & IRQ_TXUNDER) {
2274                 unsigned short val = rd_reg16(info, TCR);
2275                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2276                 wr_reg16(info, TCR, val); /* clear reset bit */
2277         }
2278
2279         if (info->tx_active) {
2280                 if (info->params.mode != MGSL_MODE_ASYNC) {
2281                         if (status & IRQ_TXUNDER)
2282                                 info->icount.txunder++;
2283                         else if (status & IRQ_TXIDLE)
2284                                 info->icount.txok++;
2285                 }
2286
2287                 info->tx_active = false;
2288                 info->tx_count = 0;
2289
2290                 del_timer(&info->tx_timer);
2291
2292                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2293                         info->signals &= ~SerialSignal_RTS;
2294                         info->drop_rts_on_tx_done = false;
2295                         set_signals(info);
2296                 }
2297
2298 #if SYNCLINK_GENERIC_HDLC
2299                 if (info->netcount)
2300                         hdlcdev_tx_done(info);
2301                 else
2302 #endif
2303                 {
2304                         if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2305                                 tx_stop(info);
2306                                 return;
2307                         }
2308                         info->pending_bh |= BH_TRANSMIT;
2309                 }
2310         }
2311 }
2312
2313 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2314 {
2315         struct cond_wait *w, *prev;
2316
2317         /* wake processes waiting for specific transitions */
2318         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2319                 if (w->data & changed) {
2320                         w->data = state;
2321                         wake_up_interruptible(&w->q);
2322                         if (prev != NULL)
2323                                 prev->next = w->next;
2324                         else
2325                                 info->gpio_wait_q = w->next;
2326                 } else
2327                         prev = w;
2328         }
2329 }
2330
2331 /* interrupt service routine
2332  *
2333  *      irq     interrupt number
2334  *      dev_id  device ID supplied during interrupt registration
2335  */
2336 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2337 {
2338         struct slgt_info *info = dev_id;
2339         unsigned int gsr;
2340         unsigned int i;
2341
2342         DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2343
2344         spin_lock(&info->lock);
2345
2346         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2347                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2348                 info->irq_occurred = true;
2349                 for(i=0; i < info->port_count ; i++) {
2350                         if (info->port_array[i] == NULL)
2351                                 continue;
2352                         if (gsr & (BIT8 << i))
2353                                 isr_serial(info->port_array[i]);
2354                         if (gsr & (BIT16 << (i*2)))
2355                                 isr_rdma(info->port_array[i]);
2356                         if (gsr & (BIT17 << (i*2)))
2357                                 isr_tdma(info->port_array[i]);
2358                 }
2359         }
2360
2361         if (info->gpio_present) {
2362                 unsigned int state;
2363                 unsigned int changed;
2364                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2365                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2366                         /* read latched state of GPIO signals */
2367                         state = rd_reg32(info, IOVR);
2368                         /* clear pending GPIO interrupt bits */
2369                         wr_reg32(info, IOSR, changed);
2370                         for (i=0 ; i < info->port_count ; i++) {
2371                                 if (info->port_array[i] != NULL)
2372                                         isr_gpio(info->port_array[i], changed, state);
2373                         }
2374                 }
2375         }
2376
2377         for(i=0; i < info->port_count ; i++) {
2378                 struct slgt_info *port = info->port_array[i];
2379
2380                 if (port && (port->port.count || port->netcount) &&
2381                     port->pending_bh && !port->bh_running &&
2382                     !port->bh_requested) {
2383                         DBGISR(("%s bh queued\n", port->device_name));
2384                         schedule_work(&port->task);
2385                         port->bh_requested = true;
2386                 }
2387         }
2388
2389         spin_unlock(&info->lock);
2390
2391         DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2392         return IRQ_HANDLED;
2393 }
2394
2395 static int startup(struct slgt_info *info)
2396 {
2397         DBGINFO(("%s startup\n", info->device_name));
2398
2399         if (info->port.flags & ASYNC_INITIALIZED)
2400                 return 0;
2401
2402         if (!info->tx_buf) {
2403                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2404                 if (!info->tx_buf) {
2405                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2406                         return -ENOMEM;
2407                 }
2408         }
2409
2410         info->pending_bh = 0;
2411
2412         memset(&info->icount, 0, sizeof(info->icount));
2413
2414         /* program hardware for current parameters */
2415         change_params(info);
2416
2417         if (info->port.tty)
2418                 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2419
2420         info->port.flags |= ASYNC_INITIALIZED;
2421
2422         return 0;
2423 }
2424
2425 /*
2426  *  called by close() and hangup() to shutdown hardware
2427  */
2428 static void shutdown(struct slgt_info *info)
2429 {
2430         unsigned long flags;
2431
2432         if (!(info->port.flags & ASYNC_INITIALIZED))
2433                 return;
2434
2435         DBGINFO(("%s shutdown\n", info->device_name));
2436
2437         /* clear status wait queue because status changes */
2438         /* can't happen after shutting down the hardware */
2439         wake_up_interruptible(&info->status_event_wait_q);
2440         wake_up_interruptible(&info->event_wait_q);
2441
2442         del_timer_sync(&info->tx_timer);
2443         del_timer_sync(&info->rx_timer);
2444
2445         kfree(info->tx_buf);
2446         info->tx_buf = NULL;
2447
2448         spin_lock_irqsave(&info->lock,flags);
2449
2450         tx_stop(info);
2451         rx_stop(info);
2452
2453         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2454
2455         if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
2456                 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2457                 set_signals(info);
2458         }
2459
2460         flush_cond_wait(&info->gpio_wait_q);
2461
2462         spin_unlock_irqrestore(&info->lock,flags);
2463
2464         if (info->port.tty)
2465                 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2466
2467         info->port.flags &= ~ASYNC_INITIALIZED;
2468 }
2469
2470 static void program_hw(struct slgt_info *info)
2471 {
2472         unsigned long flags;
2473
2474         spin_lock_irqsave(&info->lock,flags);
2475
2476         rx_stop(info);
2477         tx_stop(info);
2478
2479         if (info->params.mode != MGSL_MODE_ASYNC ||
2480             info->netcount)
2481                 sync_mode(info);
2482         else
2483                 async_mode(info);
2484
2485         set_signals(info);
2486
2487         info->dcd_chkcount = 0;
2488         info->cts_chkcount = 0;
2489         info->ri_chkcount = 0;
2490         info->dsr_chkcount = 0;
2491
2492         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
2493         get_signals(info);
2494
2495         if (info->netcount ||
2496             (info->port.tty && info->port.tty->termios->c_cflag & CREAD))
2497                 rx_start(info);
2498
2499         spin_unlock_irqrestore(&info->lock,flags);
2500 }
2501
2502 /*
2503  * reconfigure adapter based on new parameters
2504  */
2505 static void change_params(struct slgt_info *info)
2506 {
2507         unsigned cflag;
2508         int bits_per_char;
2509
2510         if (!info->port.tty || !info->port.tty->termios)
2511                 return;
2512         DBGINFO(("%s change_params\n", info->device_name));
2513
2514         cflag = info->port.tty->termios->c_cflag;
2515
2516         /* if B0 rate (hangup) specified then negate DTR and RTS */
2517         /* otherwise assert DTR and RTS */
2518         if (cflag & CBAUD)
2519                 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2520         else
2521                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2522
2523         /* byte size and parity */
2524
2525         switch (cflag & CSIZE) {
2526         case CS5: info->params.data_bits = 5; break;
2527         case CS6: info->params.data_bits = 6; break;
2528         case CS7: info->params.data_bits = 7; break;
2529         case CS8: info->params.data_bits = 8; break;
2530         default:  info->params.data_bits = 7; break;
2531         }
2532
2533         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2534
2535         if (cflag & PARENB)
2536                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2537         else
2538                 info->params.parity = ASYNC_PARITY_NONE;
2539
2540         /* calculate number of jiffies to transmit a full
2541          * FIFO (32 bytes) at specified data rate
2542          */
2543         bits_per_char = info->params.data_bits +
2544                         info->params.stop_bits + 1;
2545
2546         info->params.data_rate = tty_get_baud_rate(info->port.tty);
2547
2548         if (info->params.data_rate) {
2549                 info->timeout = (32*HZ*bits_per_char) /
2550                                 info->params.data_rate;
2551         }
2552         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2553
2554         if (cflag & CRTSCTS)
2555                 info->port.flags |= ASYNC_CTS_FLOW;
2556         else
2557                 info->port.flags &= ~ASYNC_CTS_FLOW;
2558
2559         if (cflag & CLOCAL)
2560                 info->port.flags &= ~ASYNC_CHECK_CD;
2561         else
2562                 info->port.flags |= ASYNC_CHECK_CD;
2563
2564         /* process tty input control flags */
2565
2566         info->read_status_mask = IRQ_RXOVER;
2567         if (I_INPCK(info->port.tty))
2568                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2569         if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2570                 info->read_status_mask |= MASK_BREAK;
2571         if (I_IGNPAR(info->port.tty))
2572                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2573         if (I_IGNBRK(info->port.tty)) {
2574                 info->ignore_status_mask |= MASK_BREAK;
2575                 /* If ignoring parity and break indicators, ignore
2576                  * overruns too.  (For real raw support).
2577                  */
2578                 if (I_IGNPAR(info->port.tty))
2579                         info->ignore_status_mask |= MASK_OVERRUN;
2580         }
2581
2582         program_hw(info);
2583 }
2584
2585 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2586 {
2587         DBGINFO(("%s get_stats\n",  info->device_name));
2588         if (!user_icount) {
2589                 memset(&info->icount, 0, sizeof(info->icount));
2590         } else {
2591                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2592                         return -EFAULT;
2593         }
2594         return 0;
2595 }
2596
2597 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2598 {
2599         DBGINFO(("%s get_params\n", info->device_name));
2600         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2601                 return -EFAULT;
2602         return 0;
2603 }
2604
2605 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2606 {
2607         unsigned long flags;
2608         MGSL_PARAMS tmp_params;
2609
2610         DBGINFO(("%s set_params\n", info->device_name));
2611         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2612                 return -EFAULT;
2613
2614         spin_lock_irqsave(&info->lock, flags);
2615         memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2616         spin_unlock_irqrestore(&info->lock, flags);
2617
2618         change_params(info);
2619
2620         return 0;
2621 }
2622
2623 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2624 {
2625         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2626         if (put_user(info->idle_mode, idle_mode))
2627                 return -EFAULT;
2628         return 0;
2629 }
2630
2631 static int set_txidle(struct slgt_info *info, int idle_mode)
2632 {
2633         unsigned long flags;
2634         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2635         spin_lock_irqsave(&info->lock,flags);
2636         info->idle_mode = idle_mode;
2637         if (info->params.mode != MGSL_MODE_ASYNC)
2638                 tx_set_idle(info);
2639         spin_unlock_irqrestore(&info->lock,flags);
2640         return 0;
2641 }
2642
2643 static int tx_enable(struct slgt_info *info, int enable)
2644 {
2645         unsigned long flags;
2646         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2647         spin_lock_irqsave(&info->lock,flags);
2648         if (enable) {
2649                 if (!info->tx_enabled)
2650                         tx_start(info);
2651         } else {
2652                 if (info->tx_enabled)
2653                         tx_stop(info);
2654         }
2655         spin_unlock_irqrestore(&info->lock,flags);
2656         return 0;
2657 }
2658
2659 /*
2660  * abort transmit HDLC frame
2661  */
2662 static int tx_abort(struct slgt_info *info)
2663 {
2664         unsigned long flags;
2665         DBGINFO(("%s tx_abort\n", info->device_name));
2666         spin_lock_irqsave(&info->lock,flags);
2667         tdma_reset(info);
2668         spin_unlock_irqrestore(&info->lock,flags);
2669         return 0;
2670 }
2671
2672 static int rx_enable(struct slgt_info *info, int enable)
2673 {
2674         unsigned long flags;
2675         unsigned int rbuf_fill_level;
2676         DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2677         spin_lock_irqsave(&info->lock,flags);
2678         /*
2679          * enable[31..16] = receive DMA buffer fill level
2680          * 0 = noop (leave fill level unchanged)
2681          * fill level must be multiple of 4 and <= buffer size
2682          */
2683         rbuf_fill_level = ((unsigned int)enable) >> 16;
2684         if (rbuf_fill_level) {
2685                 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2686                         spin_unlock_irqrestore(&info->lock, flags);
2687                         return -EINVAL;
2688                 }
2689                 info->rbuf_fill_level = rbuf_fill_level;
2690                 rx_stop(info); /* restart receiver to use new fill level */
2691         }
2692
2693         /*
2694          * enable[1..0] = receiver enable command
2695          * 0 = disable
2696          * 1 = enable
2697          * 2 = enable or force hunt mode if already enabled
2698          */
2699         enable &= 3;
2700         if (enable) {
2701                 if (!info->rx_enabled)
2702                         rx_start(info);
2703                 else if (enable == 2) {
2704                         /* force hunt mode (write 1 to RCR[3]) */
2705                         wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2706                 }
2707         } else {
2708                 if (info->rx_enabled)
2709                         rx_stop(info);
2710         }
2711         spin_unlock_irqrestore(&info->lock,flags);
2712         return 0;
2713 }
2714
2715 /*
2716  *  wait for specified event to occur
2717  */
2718 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2719 {
2720         unsigned long flags;
2721         int s;
2722         int rc=0;
2723         struct mgsl_icount cprev, cnow;
2724         int events;
2725         int mask;
2726         struct  _input_signal_events oldsigs, newsigs;
2727         DECLARE_WAITQUEUE(wait, current);
2728
2729         if (get_user(mask, mask_ptr))
2730                 return -EFAULT;
2731
2732         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2733
2734         spin_lock_irqsave(&info->lock,flags);
2735
2736         /* return immediately if state matches requested events */
2737         get_signals(info);
2738         s = info->signals;
2739
2740         events = mask &
2741                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2742                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2743                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2744                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2745         if (events) {
2746                 spin_unlock_irqrestore(&info->lock,flags);
2747                 goto exit;
2748         }
2749
2750         /* save current irq counts */
2751         cprev = info->icount;
2752         oldsigs = info->input_signal_events;
2753
2754         /* enable hunt and idle irqs if needed */
2755         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2756                 unsigned short val = rd_reg16(info, SCR);
2757                 if (!(val & IRQ_RXIDLE))
2758                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2759         }
2760
2761         set_current_state(TASK_INTERRUPTIBLE);
2762         add_wait_queue(&info->event_wait_q, &wait);
2763
2764         spin_unlock_irqrestore(&info->lock,flags);
2765
2766         for(;;) {
2767                 schedule();
2768                 if (signal_pending(current)) {
2769                         rc = -ERESTARTSYS;
2770                         break;
2771                 }
2772
2773                 /* get current irq counts */
2774                 spin_lock_irqsave(&info->lock,flags);
2775                 cnow = info->icount;
2776                 newsigs = info->input_signal_events;
2777                 set_current_state(TASK_INTERRUPTIBLE);
2778                 spin_unlock_irqrestore(&info->lock,flags);
2779
2780                 /* if no change, wait aborted for some reason */
2781                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2782                     newsigs.dsr_down == oldsigs.dsr_down &&
2783                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2784                     newsigs.dcd_down == oldsigs.dcd_down &&
2785                     newsigs.cts_up   == oldsigs.cts_up   &&
2786                     newsigs.cts_down == oldsigs.cts_down &&
2787                     newsigs.ri_up    == oldsigs.ri_up    &&
2788                     newsigs.ri_down  == oldsigs.ri_down  &&
2789                     cnow.exithunt    == cprev.exithunt   &&
2790                     cnow.rxidle      == cprev.rxidle) {
2791                         rc = -EIO;
2792                         break;
2793                 }
2794
2795                 events = mask &
2796                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2797                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2798                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2799                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2800                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2801                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2802                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2803                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2804                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2805                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2806                 if (events)
2807                         break;
2808
2809                 cprev = cnow;
2810                 oldsigs = newsigs;
2811         }
2812
2813         remove_wait_queue(&info->event_wait_q, &wait);
2814         set_current_state(TASK_RUNNING);
2815
2816
2817         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2818                 spin_lock_irqsave(&info->lock,flags);
2819                 if (!waitqueue_active(&info->event_wait_q)) {
2820                         /* disable enable exit hunt mode/idle rcvd IRQs */
2821                         wr_reg16(info, SCR,
2822                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2823                 }
2824                 spin_unlock_irqrestore(&info->lock,flags);
2825         }
2826 exit:
2827         if (rc == 0)
2828                 rc = put_user(events, mask_ptr);
2829         return rc;
2830 }
2831
2832 static int get_interface(struct slgt_info *info, int __user *if_mode)
2833 {
2834         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2835         if (put_user(info->if_mode, if_mode))
2836                 return -EFAULT;
2837         return 0;
2838 }
2839
2840 static int set_interface(struct slgt_info *info, int if_mode)
2841 {
2842         unsigned long flags;
2843         unsigned short val;
2844
2845         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2846         spin_lock_irqsave(&info->lock,flags);
2847         info->if_mode = if_mode;
2848
2849         msc_set_vcr(info);
2850
2851         /* TCR (tx control) 07  1=RTS driver control */
2852         val = rd_reg16(info, TCR);
2853         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2854                 val |= BIT7;
2855         else
2856                 val &= ~BIT7;
2857         wr_reg16(info, TCR, val);
2858
2859         spin_unlock_irqrestore(&info->lock,flags);
2860         return 0;
2861 }
2862
2863 /*
2864  * set general purpose IO pin state and direction
2865  *
2866  * user_gpio fields:
2867  * state   each bit indicates a pin state
2868  * smask   set bit indicates pin state to set
2869  * dir     each bit indicates a pin direction (0=input, 1=output)
2870  * dmask   set bit indicates pin direction to set
2871  */
2872 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2873 {
2874         unsigned long flags;
2875         struct gpio_desc gpio;
2876         __u32 data;
2877
2878         if (!info->gpio_present)
2879                 return -EINVAL;
2880         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2881                 return -EFAULT;
2882         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2883                  info->device_name, gpio.state, gpio.smask,
2884                  gpio.dir, gpio.dmask));
2885
2886         spin_lock_irqsave(&info->lock,flags);
2887         if (gpio.dmask) {
2888                 data = rd_reg32(info, IODR);
2889                 data |= gpio.dmask & gpio.dir;
2890                 data &= ~(gpio.dmask & ~gpio.dir);
2891                 wr_reg32(info, IODR, data);
2892         }
2893         if (gpio.smask) {
2894                 data = rd_reg32(info, IOVR);
2895                 data |= gpio.smask & gpio.state;
2896                 data &= ~(gpio.smask & ~gpio.state);
2897                 wr_reg32(info, IOVR, data);
2898         }
2899         spin_unlock_irqrestore(&info->lock,flags);
2900
2901         return 0;
2902 }
2903
2904 /*
2905  * get general purpose IO pin state and direction
2906  */
2907 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2908 {
2909         struct gpio_desc gpio;
2910         if (!info->gpio_present)
2911                 return -EINVAL;
2912         gpio.state = rd_reg32(info, IOVR);
2913         gpio.smask = 0xffffffff;
2914         gpio.dir   = rd_reg32(info, IODR);
2915         gpio.dmask = 0xffffffff;
2916         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2917                 return -EFAULT;
2918         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2919                  info->device_name, gpio.state, gpio.dir));
2920         return 0;
2921 }
2922
2923 /*
2924  * conditional wait facility
2925  */
2926 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2927 {
2928         init_waitqueue_head(&w->q);
2929         init_waitqueue_entry(&w->wait, current);
2930         w->data = data;
2931 }
2932
2933 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2934 {
2935         set_current_state(TASK_INTERRUPTIBLE);
2936         add_wait_queue(&w->q, &w->wait);
2937         w->next = *head;
2938         *head = w;
2939 }
2940
2941 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2942 {
2943         struct cond_wait *w, *prev;
2944         remove_wait_queue(&cw->q, &cw->wait);
2945         set_current_state(TASK_RUNNING);
2946         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2947                 if (w == cw) {
2948                         if (prev != NULL)
2949                                 prev->next = w->next;
2950                         else
2951                                 *head = w->next;
2952                         break;
2953                 }
2954         }
2955 }
2956
2957 static void flush_cond_wait(struct cond_wait **head)
2958 {
2959         while (*head != NULL) {
2960                 wake_up_interruptible(&(*head)->q);
2961                 *head = (*head)->next;
2962         }
2963 }
2964
2965 /*
2966  * wait for general purpose I/O pin(s) to enter specified state
2967  *
2968  * user_gpio fields:
2969  * state - bit indicates target pin state
2970  * smask - set bit indicates watched pin
2971  *
2972  * The wait ends when at least one watched pin enters the specified
2973  * state. When 0 (no error) is returned, user_gpio->state is set to the
2974  * state of all GPIO pins when the wait ends.
2975  *
2976  * Note: Each pin may be a dedicated input, dedicated output, or
2977  * configurable input/output. The number and configuration of pins
2978  * varies with the specific adapter model. Only input pins (dedicated
2979  * or configured) can be monitored with this function.
2980  */
2981 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2982 {
2983         unsigned long flags;
2984         int rc = 0;
2985         struct gpio_desc gpio;
2986         struct cond_wait wait;
2987         u32 state;
2988
2989         if (!info->gpio_present)
2990                 return -EINVAL;
2991         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2992                 return -EFAULT;
2993         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2994                  info->device_name, gpio.state, gpio.smask));
2995         /* ignore output pins identified by set IODR bit */
2996         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2997                 return -EINVAL;
2998         init_cond_wait(&wait, gpio.smask);
2999
3000         spin_lock_irqsave(&info->lock, flags);
3001         /* enable interrupts for watched pins */
3002         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3003         /* get current pin states */
3004         state = rd_reg32(info, IOVR);
3005
3006         if (gpio.smask & ~(state ^ gpio.state)) {
3007                 /* already in target state */
3008                 gpio.state = state;
3009         } else {
3010                 /* wait for target state */
3011                 add_cond_wait(&info->gpio_wait_q, &wait);
3012                 spin_unlock_irqrestore(&info->lock, flags);
3013                 schedule();
3014                 if (signal_pending(current))
3015                         rc = -ERESTARTSYS;
3016                 else
3017                         gpio.state = wait.data;
3018                 spin_lock_irqsave(&info->lock, flags);
3019                 remove_cond_wait(&info->gpio_wait_q, &wait);
3020         }
3021
3022         /* disable all GPIO interrupts if no waiting processes */
3023         if (info->gpio_wait_q == NULL)
3024                 wr_reg32(info, IOER, 0);
3025         spin_unlock_irqrestore(&info->lock,flags);
3026
3027         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3028                 rc = -EFAULT;
3029         return rc;
3030 }
3031
3032 static int modem_input_wait(struct slgt_info *info,int arg)
3033 {
3034         unsigned long flags;
3035         int rc;
3036         struct mgsl_icount cprev, cnow;
3037         DECLARE_WAITQUEUE(wait, current);
3038
3039         /* save current irq counts */
3040         spin_lock_irqsave(&info->lock,flags);
3041         cprev = info->icount;
3042         add_wait_queue(&info->status_event_wait_q, &wait);
3043         set_current_state(TASK_INTERRUPTIBLE);
3044         spin_unlock_irqrestore(&info->lock,flags);
3045
3046         for(;;) {
3047                 schedule();
3048                 if (signal_pending(current)) {
3049                         rc = -ERESTARTSYS;
3050                         break;
3051                 }
3052
3053                 /* get new irq counts */
3054                 spin_lock_irqsave(&info->lock,flags);
3055                 cnow = info->icount;
3056                 set_current_state(TASK_INTERRUPTIBLE);
3057                 spin_unlock_irqrestore(&info->lock,flags);
3058
3059                 /* if no change, wait aborted for some reason */
3060                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3061                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3062                         rc = -EIO;
3063                         break;
3064                 }
3065
3066                 /* check for change in caller specified modem input */
3067                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3068                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3069                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
3070                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3071                         rc = 0;
3072                         break;
3073                 }
3074
3075                 cprev = cnow;
3076         }
3077         remove_wait_queue(&info->status_event_wait_q, &wait);
3078         set_current_state(TASK_RUNNING);
3079         return rc;
3080 }
3081
3082 /*
3083  *  return state of serial control and status signals
3084  */
3085 static int tiocmget(struct tty_struct *tty, struct file *file)
3086 {
3087         struct slgt_info *info = tty->driver_data;
3088         unsigned int result;
3089         unsigned long flags;
3090
3091         spin_lock_irqsave(&info->lock,flags);
3092         get_signals(info);
3093         spin_unlock_irqrestore(&info->lock,flags);
3094
3095         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3096                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3097                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3098                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
3099                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3100                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3101
3102         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3103         return result;
3104 }
3105
3106 /*
3107  * set modem control signals (DTR/RTS)
3108  *
3109  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3110  *              TIOCMSET = set/clear signal values
3111  *      value   bit mask for command
3112  */
3113 static int tiocmset(struct tty_struct *tty, struct file *file,
3114                     unsigned int set, unsigned int clear)
3115 {
3116         struct slgt_info *info = tty->driver_data;
3117         unsigned long flags;
3118
3119         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3120
3121         if (set & TIOCM_RTS)
3122                 info->signals |= SerialSignal_RTS;
3123         if (set & TIOCM_DTR)
3124                 info->signals |= SerialSignal_DTR;
3125         if (clear & TIOCM_RTS)
3126                 info->signals &= ~SerialSignal_RTS;
3127         if (clear & TIOCM_DTR)
3128                 info->signals &= ~SerialSignal_DTR;
3129
3130         spin_lock_irqsave(&info->lock,flags);
3131         set_signals(info);
3132         spin_unlock_irqrestore(&info->lock,flags);
3133         return 0;
3134 }
3135
3136 /*
3137  *  block current process until the device is ready to open
3138  */
3139 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3140                            struct slgt_info *info)
3141 {
3142         DECLARE_WAITQUEUE(wait, current);
3143         int             retval;
3144         bool            do_clocal = false;
3145         bool            extra_count = false;
3146         unsigned long   flags;
3147
3148         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3149
3150         if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3151                 /* nonblock mode is set or port is not enabled */
3152                 info->port.flags |= ASYNC_NORMAL_ACTIVE;
3153                 return 0;
3154         }
3155
3156         if (tty->termios->c_cflag & CLOCAL)
3157                 do_clocal = true;
3158
3159         /* Wait for carrier detect and the line to become
3160          * free (i.e., not in use by the callout).  While we are in
3161          * this loop, info->port.count is dropped by one, so that
3162          * close() knows when to free things.  We restore it upon
3163          * exit, either normal or abnormal.
3164          */
3165
3166         retval = 0;
3167         add_wait_queue(&info->port.open_wait, &wait);
3168
3169         spin_lock_irqsave(&info->lock, flags);
3170         if (!tty_hung_up_p(filp)) {
3171                 extra_count = true;
3172                 info->port.count--;
3173         }
3174         spin_unlock_irqrestore(&info->lock, flags);
3175         info->port.blocked_open++;
3176
3177         while (1) {
3178                 if ((tty->termios->c_cflag & CBAUD)) {
3179                         spin_lock_irqsave(&info->lock,flags);
3180                         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3181                         set_signals(info);
3182                         spin_unlock_irqrestore(&info->lock,flags);
3183                 }
3184
3185                 set_current_state(TASK_INTERRUPTIBLE);
3186
3187                 if (tty_hung_up_p(filp) || !(info->port.flags & ASYNC_INITIALIZED)){
3188                         retval = (info->port.flags & ASYNC_HUP_NOTIFY) ?
3189                                         -EAGAIN : -ERESTARTSYS;
3190                         break;
3191                 }
3192
3193                 spin_lock_irqsave(&info->lock,flags);
3194                 get_signals(info);
3195                 spin_unlock_irqrestore(&info->lock,flags);
3196
3197                 if (!(info->port.flags & ASYNC_CLOSING) &&
3198                     (do_clocal || (info->signals & SerialSignal_DCD)) ) {
3199                         break;
3200                 }
3201
3202                 if (signal_pending(current)) {
3203                         retval = -ERESTARTSYS;
3204                         break;
3205                 }
3206
3207                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3208                 schedule();
3209         }
3210
3211         set_current_state(TASK_RUNNING);
3212         remove_wait_queue(&info->port.open_wait, &wait);
3213
3214         if (extra_count)
3215                 info->port.count++;
3216         info->port.blocked_open--;
3217
3218         if (!retval)
3219                 info->port.flags |= ASYNC_NORMAL_ACTIVE;
3220
3221         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3222         return retval;
3223 }
3224
3225 static int alloc_tmp_rbuf(struct slgt_info *info)
3226 {
3227         info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3228         if (info->tmp_rbuf == NULL)
3229                 return -ENOMEM;
3230         return 0;
3231 }
3232
3233 static void free_tmp_rbuf(struct slgt_info *info)
3234 {
3235         kfree(info->tmp_rbuf);
3236         info->tmp_rbuf = NULL;
3237 }
3238
3239 /*
3240  * allocate DMA descriptor lists.
3241  */
3242 static int alloc_desc(struct slgt_info *info)
3243 {
3244         unsigned int i;
3245         unsigned int pbufs;
3246
3247         /* allocate memory to hold descriptor lists */
3248         info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3249         if (info->bufs == NULL)
3250                 return -ENOMEM;
3251
3252         memset(info->bufs, 0, DESC_LIST_SIZE);
3253
3254         info->rbufs = (struct slgt_desc*)info->bufs;
3255         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3256
3257         pbufs = (unsigned int)info->bufs_dma_addr;
3258
3259         /*
3260          * Build circular lists of descriptors
3261          */
3262
3263         for (i=0; i < info->rbuf_count; i++) {
3264                 /* physical address of this descriptor */
3265                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3266
3267                 /* physical address of next descriptor */
3268                 if (i == info->rbuf_count - 1)
3269                         info->rbufs[i].next = cpu_to_le32(pbufs);
3270                 else
3271                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3272                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3273         }
3274
3275         for (i=0; i < info->tbuf_count; i++) {
3276                 /* physical address of this descriptor */
3277                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3278
3279                 /* physical address of next descriptor */
3280                 if (i == info->tbuf_count - 1)
3281                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3282                 else
3283                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3284         }
3285
3286         return 0;
3287 }
3288
3289 static void free_desc(struct slgt_info *info)
3290 {
3291         if (info->bufs != NULL) {
3292                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3293                 info->bufs  = NULL;
3294                 info->rbufs = NULL;
3295                 info->tbufs = NULL;
3296         }
3297 }
3298
3299 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3300 {
3301         int i;
3302         for (i=0; i < count; i++) {
3303                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3304                         return -ENOMEM;
3305                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3306         }
3307         return 0;
3308 }
3309
3310 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3311 {
3312         int i;
3313         for (i=0; i < count; i++) {
3314                 if (bufs[i].buf == NULL)
3315                         continue;
3316                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3317                 bufs[i].buf = NULL;
3318         }
3319 }
3320
3321 static int alloc_dma_bufs(struct slgt_info *info)
3322 {
3323         info->rbuf_count = 32;
3324         info->tbuf_count = 32;
3325
3326         if (alloc_desc(info) < 0 ||
3327             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3328             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3329             alloc_tmp_rbuf(info) < 0) {
3330                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3331                 return -ENOMEM;
3332         }
3333         reset_rbufs(info);
3334         return 0;
3335 }
3336
3337 static void free_dma_bufs(struct slgt_info *info)
3338 {
3339         if (info->bufs) {
3340                 free_bufs(info, info->rbufs, info->rbuf_count);
3341                 free_bufs(info, info->tbufs, info->tbuf_count);
3342                 free_desc(info);
3343         }
3344         free_tmp_rbuf(info);
3345 }
3346
3347 static int claim_resources(struct slgt_info *info)
3348 {
3349         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3350                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3351                         info->device_name, info->phys_reg_addr));
3352                 info->init_error = DiagStatus_AddressConflict;
3353                 goto errout;
3354         }
3355         else
3356                 info->reg_addr_requested = true;
3357
3358         info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3359         if (!info->reg_addr) {
3360                 DBGERR(("%s cant map device registers, addr=%08X\n",
3361                         info->device_name, info->phys_reg_addr));
3362                 info->init_error = DiagStatus_CantAssignPciResources;
3363                 goto errout;
3364         }
3365         return 0;
3366
3367 errout:
3368         release_resources(info);
3369         return -ENODEV;
3370 }
3371
3372 static void release_resources(struct slgt_info *info)
3373 {
3374         if (info->irq_requested) {
3375                 free_irq(info->irq_level, info);
3376                 info->irq_requested = false;
3377         }
3378
3379         if (info->reg_addr_requested) {
3380                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3381                 info->reg_addr_requested = false;
3382         }
3383
3384         if (info->reg_addr) {
3385                 iounmap(info->reg_addr);
3386                 info->reg_addr = NULL;
3387         }
3388 }
3389
3390 /* Add the specified device instance data structure to the
3391  * global linked list of devices and increment the device count.
3392  */
3393 static void add_device(struct slgt_info *info)
3394 {
3395         char *devstr;
3396
3397         info->next_device = NULL;
3398         info->line = slgt_device_count;
3399         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3400
3401         if (info->line < MAX_DEVICES) {
3402                 if (maxframe[info->line])
3403                         info->max_frame_size = maxframe[info->line];
3404         }
3405
3406         slgt_device_count++;
3407
3408         if (!slgt_device_list)
3409                 slgt_device_list = info;
3410         else {
3411                 struct slgt_info *current_dev = slgt_device_list;
3412                 while(current_dev->next_device)
3413                         current_dev = current_dev->next_device;
3414                 current_dev->next_device = info;
3415         }
3416
3417         if (info->max_frame_size < 4096)
3418                 info->max_frame_size = 4096;
3419         else if (info->max_frame_size > 65535)
3420                 info->max_frame_size = 65535;
3421
3422         switch(info->pdev->device) {
3423         case SYNCLINK_GT_DEVICE_ID:
3424                 devstr = "GT";
3425                 break;
3426         case SYNCLINK_GT2_DEVICE_ID:
3427                 devstr = "GT2";
3428                 break;
3429         case SYNCLINK_GT4_DEVICE_ID:
3430                 devstr = "GT4";
3431                 break;
3432         case SYNCLINK_AC_DEVICE_ID:
3433                 devstr = "AC";
3434                 info->params.mode = MGSL_MODE_ASYNC;
3435                 break;
3436         default:
3437                 devstr = "(unknown model)";
3438         }
3439         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3440                 devstr, info->device_name, info->phys_reg_addr,
3441                 info->irq_level, info->max_frame_size);
3442
3443 #if SYNCLINK_GENERIC_HDLC
3444         hdlcdev_init(info);
3445 #endif
3446 }
3447
3448 /*
3449  *  allocate device instance structure, return NULL on failure
3450  */
3451 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3452 {
3453         struct slgt_info *info;
3454
3455         info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3456
3457         if (!info) {
3458                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3459                         driver_name, adapter_num, port_num));
3460         } else {
3461                 tty_port_init(&info->port);
3462                 info->magic = MGSL_MAGIC;
3463                 INIT_WORK(&info->task, bh_handler);
3464                 info->max_frame_size = 4096;
3465                 info->rbuf_fill_level = DMABUFSIZE;
3466                 info->port.close_delay = 5*HZ/10;
3467                 info->port.closing_wait = 30*HZ;
3468                 init_waitqueue_head(&info->status_event_wait_q);
3469                 init_waitqueue_head(&info->event_wait_q);
3470                 spin_lock_init(&info->netlock);
3471                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3472                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3473                 info->adapter_num = adapter_num;
3474                 info->port_num = port_num;
3475
3476                 setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3477                 setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3478
3479                 /* Copy configuration info to device instance data */
3480                 info->pdev = pdev;
3481                 info->irq_level = pdev->irq;
3482                 info->phys_reg_addr = pci_resource_start(pdev,0);
3483
3484                 info->bus_type = MGSL_BUS_TYPE_PCI;
3485                 info->irq_flags = IRQF_SHARED;
3486
3487                 info->init_error = -1; /* assume error, set to 0 on successful init */
3488         }
3489
3490         return info;
3491 }
3492
3493 static void device_init(int adapter_num, struct pci_dev *pdev)
3494 {
3495         struct slgt_info *port_array[SLGT_MAX_PORTS];
3496         int i;
3497         int port_count = 1;
3498
3499         if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3500                 port_count = 2;
3501         else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3502                 port_count = 4;
3503
3504         /* allocate device instances for all ports */
3505         for (i=0; i < port_count; ++i) {
3506                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3507                 if (port_array[i] == NULL) {
3508                         for (--i; i >= 0; --i)
3509                                 kfree(port_array[i]);
3510                         return;
3511                 }
3512         }
3513
3514         /* give copy of port_array to all ports and add to device list  */
3515         for (i=0; i < port_count; ++i) {
3516                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3517                 add_device(port_array[i]);
3518                 port_array[i]->port_count = port_count;
3519                 spin_lock_init(&port_array[i]->lock);
3520         }
3521
3522         /* Allocate and claim adapter resources */
3523         if (!claim_resources(port_array[0])) {
3524
3525                 alloc_dma_bufs(port_array[0]);
3526
3527                 /* copy resource information from first port to others */
3528                 for (i = 1; i < port_count; ++i) {
3529                         port_array[i]->lock      = port_array[0]->lock;
3530                         port_array[i]->irq_level = port_array[0]->irq_level;
3531                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3532                         alloc_dma_bufs(port_array[i]);
3533                 }
3534
3535                 if (request_irq(port_array[0]->irq_level,
3536                                         slgt_interrupt,
3537                                         port_array[0]->irq_flags,
3538                                         port_array[0]->device_name,
3539                                         port_array[0]) < 0) {
3540                         DBGERR(("%s request_irq failed IRQ=%d\n",
3541                                 port_array[0]->device_name,
3542                                 port_array[0]->irq_level));
3543                 } else {
3544                         port_array[0]->irq_requested = true;
3545                         adapter_test(port_array[0]);
3546                         for (i=1 ; i < port_count ; i++) {
3547                                 port_array[i]->init_error = port_array[0]->init_error;
3548                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3549                         }
3550                 }
3551         }
3552
3553         for (i=0; i < port_count; ++i)
3554                 tty_register_device(serial_driver, port_array[i]->line, &(port_array[i]->pdev->dev));
3555 }
3556
3557 static int __devinit init_one(struct pci_dev *dev,
3558                               const struct pci_device_id *ent)
3559 {
3560         if (pci_enable_device(dev)) {
3561                 printk("error enabling pci device %p\n", dev);
3562                 return -EIO;
3563         }
3564         pci_set_master(dev);
3565         device_init(slgt_device_count, dev);
3566         return 0;
3567 }
3568
3569 static void __devexit remove_one(struct pci_dev *dev)
3570 {
3571 }
3572
3573 static const struct tty_operations ops = {
3574         .open = open,
3575         .close = close,
3576         .write = write,
3577         .put_char = put_char,
3578         .flush_chars = flush_chars,
3579         .write_room = write_room,
3580         .chars_in_buffer = chars_in_buffer,
3581         .flush_buffer = flush_buffer,
3582         .ioctl = ioctl,
3583         .compat_ioctl = slgt_compat_ioctl,
3584         .throttle = throttle,
3585         .unthrottle = unthrottle,
3586         .send_xchar = send_xchar,
3587         .break_ctl = set_break,
3588         .wait_until_sent = wait_until_sent,
3589         .read_proc = read_proc,
3590         .set_termios = set_termios,
3591         .stop = tx_hold,
3592         .start = tx_release,
3593         .hangup = hangup,
3594         .tiocmget = tiocmget,
3595         .tiocmset = tiocmset,
3596 };
3597
3598 static void slgt_cleanup(void)
3599 {
3600         int rc;
3601         struct slgt_info *info;
3602         struct slgt_info *tmp;
3603
3604         printk("unload %s %s\n", driver_name, driver_version);
3605
3606         if (serial_driver) {
3607                 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3608                         tty_unregister_device(serial_driver, info->line);
3609                 if ((rc = tty_unregister_driver(serial_driver)))
3610                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3611                 put_tty_driver(serial_driver);
3612         }
3613
3614         /* reset devices */
3615         info = slgt_device_list;
3616         while(info) {
3617                 reset_port(info);
3618                 info = info->next_device;
3619         }
3620
3621         /* release devices */
3622         info = slgt_device_list;
3623         while(info) {
3624 #if SYNCLINK_GENERIC_HDLC
3625                 hdlcdev_exit(info);
3626 #endif
3627                 free_dma_bufs(info);
3628                 free_tmp_rbuf(info);
3629                 if (info->port_num == 0)
3630                         release_resources(info);
3631                 tmp = info;
3632                 info = info->next_device;
3633                 kfree(tmp);
3634         }
3635
3636         if (pci_registered)
3637                 pci_unregister_driver(&pci_driver);
3638 }
3639
3640 /*
3641  *  Driver initialization entry point.
3642  */
3643 static int __init slgt_init(void)
3644 {
3645         int rc;
3646
3647         printk("%s %s\n", driver_name, driver_version);
3648
3649         serial_driver = alloc_tty_driver(MAX_DEVICES);
3650         if (!serial_driver) {
3651                 printk("%s can't allocate tty driver\n", driver_name);
3652                 return -ENOMEM;
3653         }
3654
3655         /* Initialize the tty_driver structure */
3656
3657         serial_driver->owner = THIS_MODULE;
3658         serial_driver->driver_name = tty_driver_name;
3659         serial_driver->name = tty_dev_prefix;
3660         serial_driver->major = ttymajor;
3661         serial_driver->minor_start = 64;
3662         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3663         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3664         serial_driver->init_termios = tty_std_termios;
3665         serial_driver->init_termios.c_cflag =
3666                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3667         serial_driver->init_termios.c_ispeed = 9600;
3668         serial_driver->init_termios.c_ospeed = 9600;
3669         serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3670         tty_set_operations(serial_driver, &ops);
3671         if ((rc = tty_register_driver(serial_driver)) < 0) {
3672                 DBGERR(("%s can't register serial driver\n", driver_name));
3673                 put_tty_driver(serial_driver);
3674                 serial_driver = NULL;
3675                 goto error;
3676         }
3677
3678         printk("%s %s, tty major#%d\n",
3679                 driver_name, driver_version,
3680                 serial_driver->major);
3681
3682         slgt_device_count = 0;
3683         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3684                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3685                 goto error;
3686         }
3687         pci_registered = true;
3688
3689         if (!slgt_device_list)
3690                 printk("%s no devices found\n",driver_name);
3691
3692         return 0;
3693
3694 error:
3695         slgt_cleanup();
3696         return rc;
3697 }
3698
3699 static void __exit slgt_exit(void)
3700 {
3701         slgt_cleanup();
3702 }
3703
3704 module_init(slgt_init);
3705 module_exit(slgt_exit);
3706
3707 /*
3708  * register access routines
3709  */
3710
3711 #define CALC_REGADDR() \
3712         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3713         if (addr >= 0x80) \
3714                 reg_addr += (info->port_num) * 32;
3715
3716 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3717 {
3718         CALC_REGADDR();
3719         return readb((void __iomem *)reg_addr);
3720 }
3721
3722 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3723 {
3724         CALC_REGADDR();
3725         writeb(value, (void __iomem *)reg_addr);
3726 }
3727
3728 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3729 {
3730         CALC_REGADDR();
3731         return readw((void __iomem *)reg_addr);
3732 }
3733
3734 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3735 {
3736         CALC_REGADDR();
3737         writew(value, (void __iomem *)reg_addr);
3738 }
3739
3740 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3741 {
3742         CALC_REGADDR();
3743         return readl((void __iomem *)reg_addr);
3744 }
3745
3746 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3747 {
3748         CALC_REGADDR();
3749         writel(value, (void __iomem *)reg_addr);
3750 }
3751
3752 static void rdma_reset(struct slgt_info *info)
3753 {
3754         unsigned int i;
3755
3756         /* set reset bit */
3757         wr_reg32(info, RDCSR, BIT1);
3758
3759         /* wait for enable bit cleared */
3760         for(i=0 ; i < 1000 ; i++)
3761                 if (!(rd_reg32(info, RDCSR) & BIT0))
3762                         break;
3763 }
3764
3765 static void tdma_reset(struct slgt_info *info)
3766 {
3767         unsigned int i;
3768
3769         /* set reset bit */
3770         wr_reg32(info, TDCSR, BIT1);
3771
3772         /* wait for enable bit cleared */
3773         for(i=0 ; i < 1000 ; i++)
3774                 if (!(rd_reg32(info, TDCSR) & BIT0))
3775                         break;
3776 }
3777
3778 /*
3779  * enable internal loopback
3780  * TxCLK and RxCLK are generated from BRG
3781  * and TxD is looped back to RxD internally.
3782  */
3783 static void enable_loopback(struct slgt_info *info)
3784 {
3785         /* SCR (serial control) BIT2=looopback enable */
3786         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3787
3788         if (info->params.mode != MGSL_MODE_ASYNC) {
3789                 /* CCR (clock control)
3790                  * 07..05  tx clock source (010 = BRG)
3791                  * 04..02  rx clock source (010 = BRG)
3792                  * 01      auxclk enable   (0 = disable)
3793                  * 00      BRG enable      (1 = enable)
3794                  *
3795                  * 0100 1001
3796                  */
3797                 wr_reg8(info, CCR, 0x49);
3798
3799                 /* set speed if available, otherwise use default */
3800                 if (info->params.clock_speed)
3801                         set_rate(info, info->params.clock_speed);
3802                 else
3803                         set_rate(info, 3686400);
3804         }
3805 }
3806
3807 /*
3808  *  set baud rate generator to specified rate
3809  */
3810 static void set_rate(struct slgt_info *info, u32 rate)
3811 {
3812         unsigned int div;
3813         static unsigned int osc = 14745600;
3814
3815         /* div = osc/rate - 1
3816          *
3817          * Round div up if osc/rate is not integer to
3818          * force to next slowest rate.
3819          */
3820
3821         if (rate) {
3822                 div = osc/rate;
3823                 if (!(osc % rate) && div)
3824                         div--;
3825                 wr_reg16(info, BDR, (unsigned short)div);
3826         }
3827 }
3828
3829 static void rx_stop(struct slgt_info *info)
3830 {
3831         unsigned short val;
3832
3833         /* disable and reset receiver */
3834         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3835         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3836         wr_reg16(info, RCR, val);                  /* clear reset bit */
3837
3838         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3839
3840         /* clear pending rx interrupts */
3841         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3842
3843         rdma_reset(info);
3844
3845         info->rx_enabled = false;
3846         info->rx_restart = false;
3847 }
3848
3849 static void rx_start(struct slgt_info *info)
3850 {
3851         unsigned short val;
3852
3853         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3854
3855         /* clear pending rx overrun IRQ */
3856         wr_reg16(info, SSR, IRQ_RXOVER);
3857
3858         /* reset and disable receiver */
3859         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3860         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3861         wr_reg16(info, RCR, val);                  /* clear reset bit */
3862
3863         rdma_reset(info);
3864         reset_rbufs(info);
3865
3866         /* set 1st descriptor address */
3867         wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3868
3869         if (info->params.mode != MGSL_MODE_ASYNC) {
3870                 /* enable rx DMA and DMA interrupt */
3871                 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3872         } else {
3873                 /* enable saving of rx status, rx DMA and DMA interrupt */
3874                 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3875         }
3876
3877         slgt_irq_on(info, IRQ_RXOVER);
3878
3879         /* enable receiver */
3880         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3881
3882         info->rx_restart = false;
3883         info->rx_enabled = true;
3884 }
3885
3886 static void tx_start(struct slgt_info *info)
3887 {
3888         if (!info->tx_enabled) {
3889                 wr_reg16(info, TCR,
3890                          (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
3891                 info->tx_enabled = true;
3892         }
3893
3894         if (info->tx_count) {
3895                 info->drop_rts_on_tx_done = false;
3896
3897                 if (info->params.mode != MGSL_MODE_ASYNC) {
3898                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3899                                 get_signals(info);
3900                                 if (!(info->signals & SerialSignal_RTS)) {
3901                                         info->signals |= SerialSignal_RTS;
3902                                         set_signals(info);
3903                                         info->drop_rts_on_tx_done = true;
3904                                 }
3905                         }
3906
3907                         slgt_irq_off(info, IRQ_TXDATA);
3908                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3909                         /* clear tx idle and underrun status bits */
3910                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3911                         if (info->params.mode == MGSL_MODE_HDLC)
3912                                 mod_timer(&info->tx_timer, jiffies +
3913                                                 msecs_to_jiffies(5000));
3914                 } else {
3915                         slgt_irq_off(info, IRQ_TXDATA);
3916                         slgt_irq_on(info, IRQ_TXIDLE);
3917                         /* clear tx idle status bit */
3918                         wr_reg16(info, SSR, IRQ_TXIDLE);
3919                 }
3920                 tdma_start(info);
3921                 info->tx_active = true;
3922         }
3923 }
3924
3925 /*
3926  * start transmit DMA if inactive and there are unsent buffers
3927  */
3928 static void tdma_start(struct slgt_info *info)
3929 {
3930         unsigned int i;
3931
3932         if (rd_reg32(info, TDCSR) & BIT0)
3933                 return;
3934
3935         /* transmit DMA inactive, check for unsent buffers */
3936         i = info->tbuf_start;
3937         while (!desc_count(info->tbufs[i])) {
3938                 if (++i == info->tbuf_count)
3939                         i = 0;
3940                 if (i == info->tbuf_current)
3941                         return;
3942         }
3943         info->tbuf_start = i;
3944
3945         /* there are unsent buffers, start transmit DMA */
3946
3947         /* reset needed if previous error condition */
3948         tdma_reset(info);
3949
3950         /* set 1st descriptor address */
3951         wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3952         wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
3953 }
3954
3955 static void tx_stop(struct slgt_info *info)
3956 {
3957         unsigned short val;
3958
3959         del_timer(&info->tx_timer);
3960
3961         tdma_reset(info);
3962
3963         /* reset and disable transmitter */
3964         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
3965         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3966
3967         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3968
3969         /* clear tx idle and underrun status bit */
3970         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3971
3972         reset_tbufs(info);
3973
3974         info->tx_enabled = false;
3975         info->tx_active = false;
3976 }
3977
3978 static void reset_port(struct slgt_info *info)
3979 {
3980         if (!info->reg_addr)
3981                 return;
3982
3983         tx_stop(info);
3984         rx_stop(info);
3985
3986         info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
3987         set_signals(info);
3988
3989         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3990 }
3991
3992 static void reset_adapter(struct slgt_info *info)
3993 {
3994         int i;
3995         for (i=0; i < info->port_count; ++i) {
3996                 if (info->port_array[i])
3997                         reset_port(info->port_array[i]);
3998         }
3999 }
4000
4001 static void async_mode(struct slgt_info *info)
4002 {
4003         unsigned short val;
4004
4005         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4006         tx_stop(info);
4007         rx_stop(info);
4008
4009         /* TCR (tx control)
4010          *
4011          * 15..13  mode, 010=async
4012          * 12..10  encoding, 000=NRZ
4013          * 09      parity enable
4014          * 08      1=odd parity, 0=even parity
4015          * 07      1=RTS driver control
4016          * 06      1=break enable
4017          * 05..04  character length
4018          *         00=5 bits
4019          *         01=6 bits
4020          *         10=7 bits
4021          *         11=8 bits
4022          * 03      0=1 stop bit, 1=2 stop bits
4023          * 02      reset
4024          * 01      enable
4025          * 00      auto-CTS enable
4026          */
4027         val = 0x4000;
4028
4029         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4030                 val |= BIT7;
4031
4032         if (info->params.parity != ASYNC_PARITY_NONE) {
4033                 val |= BIT9;
4034                 if (info->params.parity == ASYNC_PARITY_ODD)
4035                         val |= BIT8;
4036         }
4037
4038         switch (info->params.data_bits)
4039         {
4040         case 6: val |= BIT4; break;
4041         case 7: val |= BIT5; break;
4042         case 8: val |= BIT5 + BIT4; break;
4043         }
4044
4045         if (info->params.stop_bits != 1)
4046                 val |= BIT3;
4047
4048         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4049                 val |= BIT0;
4050
4051         wr_reg16(info, TCR, val);
4052
4053         /* RCR (rx control)
4054          *
4055          * 15..13  mode, 010=async
4056          * 12..10  encoding, 000=NRZ
4057          * 09      parity enable
4058          * 08      1=odd parity, 0=even parity
4059          * 07..06  reserved, must be 0
4060          * 05..04  character length
4061          *         00=5 bits
4062          *         01=6 bits
4063          *         10=7 bits
4064          *         11=8 bits
4065          * 03      reserved, must be zero
4066          * 02      reset
4067          * 01      enable
4068          * 00      auto-DCD enable
4069          */
4070         val = 0x4000;
4071
4072         if (info->params.parity != ASYNC_PARITY_NONE) {
4073                 val |= BIT9;
4074                 if (info->params.parity == ASYNC_PARITY_ODD)
4075                         val |= BIT8;
4076         }
4077
4078         switch (info->params.data_bits)
4079         {
4080         case 6: val |= BIT4; break;
4081         case 7: val |= BIT5; break;
4082         case 8: val |= BIT5 + BIT4; break;
4083         }
4084
4085         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4086                 val |= BIT0;
4087
4088         wr_reg16(info, RCR, val);
4089
4090         /* CCR (clock control)
4091          *
4092          * 07..05  011 = tx clock source is BRG/16
4093          * 04..02  010 = rx clock source is BRG
4094          * 01      0 = auxclk disabled
4095          * 00      1 = BRG enabled
4096          *
4097          * 0110 1001
4098          */
4099         wr_reg8(info, CCR, 0x69);
4100
4101         msc_set_vcr(info);
4102
4103         /* SCR (serial control)
4104          *
4105          * 15  1=tx req on FIFO half empty
4106          * 14  1=rx req on FIFO half full
4107          * 13  tx data  IRQ enable
4108          * 12  tx idle  IRQ enable
4109          * 11  rx break on IRQ enable
4110          * 10  rx data  IRQ enable
4111          * 09  rx break off IRQ enable
4112          * 08  overrun  IRQ enable
4113          * 07  DSR      IRQ enable
4114          * 06  CTS      IRQ enable
4115          * 05  DCD      IRQ enable
4116          * 04  RI       IRQ enable
4117          * 03  reserved, must be zero
4118          * 02  1=txd->rxd internal loopback enable
4119          * 01  reserved, must be zero
4120          * 00  1=master IRQ enable
4121          */
4122         val = BIT15 + BIT14 + BIT0;
4123         wr_reg16(info, SCR, val);
4124
4125         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4126
4127         set_rate(info, info->params.data_rate * 16);
4128
4129         if (info->params.loopback)
4130                 enable_loopback(info);
4131 }
4132
4133 static void sync_mode(struct slgt_info *info)
4134 {
4135         unsigned short val;
4136
4137         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4138         tx_stop(info);
4139         rx_stop(info);
4140
4141         /* TCR (tx control)
4142          *
4143          * 15..13  mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4144          * 12..10  encoding
4145          * 09      CRC enable
4146          * 08      CRC32
4147          * 07      1=RTS driver control
4148          * 06      preamble enable
4149          * 05..04  preamble length
4150          * 03      share open/close flag
4151          * 02      reset
4152          * 01      enable
4153          * 00      auto-CTS enable
4154          */
4155         val = BIT2;
4156
4157         switch(info->params.mode) {
4158         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4159         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4160         case MGSL_MODE_RAW:      val |= BIT13; break;
4161         }
4162         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4163                 val |= BIT7;
4164
4165         switch(info->params.encoding)
4166         {
4167         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4168         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4169         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4170         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4171         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4172         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4173         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4174         }
4175
4176         switch (info->params.crc_type & HDLC_CRC_MASK)
4177         {
4178         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4179         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4180         }
4181
4182         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4183                 val |= BIT6;
4184
4185         switch (info->params.preamble_length)
4186         {
4187         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4188         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4189         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4190         }
4191
4192         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4193                 val |= BIT0;
4194
4195         wr_reg16(info, TCR, val);
4196
4197         /* TPR (transmit preamble) */
4198
4199         switch (info->params.preamble)
4200         {
4201         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4202         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4203         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4204         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4205         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4206         default:                          val = 0x7e; break;
4207         }
4208         wr_reg8(info, TPR, (unsigned char)val);
4209
4210         /* RCR (rx control)
4211          *
4212          * 15..13  mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4213          * 12..10  encoding
4214          * 09      CRC enable
4215          * 08      CRC32
4216          * 07..03  reserved, must be 0
4217          * 02      reset
4218          * 01      enable
4219          * 00      auto-DCD enable
4220          */
4221         val = 0;
4222
4223         switch(info->params.mode) {
4224         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4225         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4226         case MGSL_MODE_RAW:      val |= BIT13; break;
4227         }
4228
4229         switch(info->params.encoding)
4230         {
4231         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4232         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4233         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4234         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4235         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4236         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4237         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4238         }
4239
4240         switch (info->params.crc_type & HDLC_CRC_MASK)
4241         {
4242         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4243         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4244         }
4245
4246         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4247                 val |= BIT0;
4248
4249         wr_reg16(info, RCR, val);
4250
4251         /* CCR (clock control)
4252          *
4253          * 07..05  tx clock source
4254          * 04..02  rx clock source
4255          * 01      auxclk enable
4256          * 00      BRG enable
4257          */
4258         val = 0;
4259
4260         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4261         {
4262                 // when RxC source is DPLL, BRG generates 16X DPLL
4263                 // reference clock, so take TxC from BRG/16 to get
4264                 // transmit clock at actual data rate
4265                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4266                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4267                 else
4268                         val |= BIT6;    /* 010, txclk = BRG */
4269         }
4270         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4271                 val |= BIT7;    /* 100, txclk = DPLL Input */
4272         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4273                 val |= BIT5;    /* 001, txclk = RXC Input */
4274
4275         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4276                 val |= BIT3;    /* 010, rxclk = BRG */
4277         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4278                 val |= BIT4;    /* 100, rxclk = DPLL */
4279         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4280                 val |= BIT2;    /* 001, rxclk = TXC Input */
4281
4282         if (info->params.clock_speed)
4283                 val |= BIT1 + BIT0;
4284
4285         wr_reg8(info, CCR, (unsigned char)val);
4286
4287         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4288         {
4289                 // program DPLL mode
4290                 switch(info->params.encoding)
4291                 {
4292                 case HDLC_ENCODING_BIPHASE_MARK:
4293                 case HDLC_ENCODING_BIPHASE_SPACE:
4294                         val = BIT7; break;
4295                 case HDLC_ENCODING_BIPHASE_LEVEL:
4296                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4297                         val = BIT7 + BIT6; break;
4298                 default: val = BIT6;    // NRZ encodings
4299                 }
4300                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4301
4302                 // DPLL requires a 16X reference clock from BRG
4303                 set_rate(info, info->params.clock_speed * 16);
4304         }
4305         else
4306                 set_rate(info, info->params.clock_speed);
4307
4308         tx_set_idle(info);
4309
4310         msc_set_vcr(info);
4311
4312         /* SCR (serial control)
4313          *
4314          * 15  1=tx req on FIFO half empty
4315          * 14  1=rx req on FIFO half full
4316          * 13  tx data  IRQ enable
4317          * 12  tx idle  IRQ enable
4318          * 11  underrun IRQ enable
4319          * 10  rx data  IRQ enable
4320          * 09  rx idle  IRQ enable
4321          * 08  overrun  IRQ enable
4322          * 07  DSR      IRQ enable
4323          * 06  CTS      IRQ enable
4324          * 05  DCD      IRQ enable
4325          * 04  RI       IRQ enable
4326          * 03  reserved, must be zero
4327          * 02  1=txd->rxd internal loopback enable
4328          * 01  reserved, must be zero
4329          * 00  1=master IRQ enable
4330          */
4331         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4332
4333         if (info->params.loopback)
4334                 enable_loopback(info);
4335 }
4336
4337 /*
4338  *  set transmit idle mode
4339  */
4340 static void tx_set_idle(struct slgt_info *info)
4341 {
4342         unsigned char val;
4343         unsigned short tcr;
4344
4345         /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4346          * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4347          */
4348         tcr = rd_reg16(info, TCR);
4349         if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4350                 /* disable preamble, set idle size to 16 bits */
4351                 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4352                 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4353                 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4354         } else if (!(tcr & BIT6)) {
4355                 /* preamble is disabled, set idle size to 8 bits */
4356                 tcr &= ~(BIT5 + BIT4);
4357         }
4358         wr_reg16(info, TCR, tcr);
4359
4360         if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4361                 /* LSB of custom tx idle specified in tx idle register */
4362                 val = (unsigned char)(info->idle_mode & 0xff);
4363         } else {
4364                 /* standard 8 bit idle patterns */
4365                 switch(info->idle_mode)
4366                 {
4367                 case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4368                 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4369                 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4370                 case HDLC_TXIDLE_ZEROS:
4371                 case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4372                 default:                         val = 0xff;
4373                 }
4374         }
4375
4376         wr_reg8(info, TIR, val);
4377 }
4378
4379 /*
4380  * get state of V24 status (input) signals
4381  */
4382 static void get_signals(struct slgt_info *info)
4383 {
4384         unsigned short status = rd_reg16(info, SSR);
4385
4386         /* clear all serial signals except DTR and RTS */
4387         info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4388
4389         if (status & BIT3)
4390                 info->signals |= SerialSignal_DSR;
4391         if (status & BIT2)
4392                 info->signals |= SerialSignal_CTS;
4393         if (status & BIT1)
4394                 info->signals |= SerialSignal_DCD;
4395         if (status & BIT0)
4396                 info->signals |= SerialSignal_RI;
4397 }
4398
4399 /*
4400  * set V.24 Control Register based on current configuration
4401  */
4402 static void msc_set_vcr(struct slgt_info *info)
4403 {
4404         unsigned char val = 0;
4405
4406         /* VCR (V.24 control)
4407          *
4408          * 07..04  serial IF select
4409          * 03      DTR
4410          * 02      RTS
4411          * 01      LL
4412          * 00      RL
4413          */
4414
4415         switch(info->if_mode & MGSL_INTERFACE_MASK)
4416         {
4417         case MGSL_INTERFACE_RS232:
4418                 val |= BIT5; /* 0010 */
4419                 break;
4420         case MGSL_INTERFACE_V35:
4421                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4422                 break;
4423         case MGSL_INTERFACE_RS422:
4424                 val |= BIT6; /* 0100 */
4425                 break;
4426         }
4427
4428         if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4429                 val |= BIT4;
4430         if (info->signals & SerialSignal_DTR)
4431                 val |= BIT3;
4432         if (info->signals & SerialSignal_RTS)
4433                 val |= BIT2;
4434         if (info->if_mode & MGSL_INTERFACE_LL)
4435                 val |= BIT1;
4436         if (info->if_mode & MGSL_INTERFACE_RL)
4437                 val |= BIT0;
4438         wr_reg8(info, VCR, val);
4439 }
4440
4441 /*
4442  * set state of V24 control (output) signals
4443  */
4444 static void set_signals(struct slgt_info *info)
4445 {
4446         unsigned char val = rd_reg8(info, VCR);
4447         if (info->signals & SerialSignal_DTR)
4448                 val |= BIT3;
4449         else
4450                 val &= ~BIT3;
4451         if (info->signals & SerialSignal_RTS)
4452                 val |= BIT2;
4453         else
4454                 val &= ~BIT2;
4455         wr_reg8(info, VCR, val);
4456 }
4457
4458 /*
4459  * free range of receive DMA buffers (i to last)
4460  */
4461 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4462 {
4463         int done = 0;
4464
4465         while(!done) {
4466                 /* reset current buffer for reuse */
4467                 info->rbufs[i].status = 0;
4468                 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4469                 if (i == last)
4470                         done = 1;
4471                 if (++i == info->rbuf_count)
4472                         i = 0;
4473         }
4474         info->rbuf_current = i;
4475 }
4476
4477 /*
4478  * mark all receive DMA buffers as free
4479  */
4480 static void reset_rbufs(struct slgt_info *info)
4481 {
4482         free_rbufs(info, 0, info->rbuf_count - 1);
4483 }
4484
4485 /*
4486  * pass receive HDLC frame to upper layer
4487  *
4488  * return true if frame available, otherwise false
4489  */
4490 static bool rx_get_frame(struct slgt_info *info)
4491 {
4492         unsigned int start, end;
4493         unsigned short status;
4494         unsigned int framesize = 0;
4495         unsigned long flags;
4496         struct tty_struct *tty = info->port.tty;
4497         unsigned char addr_field = 0xff;
4498         unsigned int crc_size = 0;
4499
4500         switch (info->params.crc_type & HDLC_CRC_MASK) {
4501         case HDLC_CRC_16_CCITT: crc_size = 2; break;
4502         case HDLC_CRC_32_CCITT: crc_size = 4; break;
4503         }
4504
4505 check_again:
4506
4507         framesize = 0;
4508         addr_field = 0xff;
4509         start = end = info->rbuf_current;
4510
4511         for (;;) {
4512                 if (!desc_complete(info->rbufs[end]))
4513                         goto cleanup;
4514
4515                 if (framesize == 0 && info->params.addr_filter != 0xff)
4516                         addr_field = info->rbufs[end].buf[0];
4517
4518                 framesize += desc_count(info->rbufs[end]);
4519
4520                 if (desc_eof(info->rbufs[end]))
4521                         break;
4522
4523                 if (++end == info->rbuf_count)
4524                         end = 0;
4525
4526                 if (end == info->rbuf_current) {
4527                         if (info->rx_enabled){
4528                                 spin_lock_irqsave(&info->lock,flags);
4529                                 rx_start(info);
4530                                 spin_unlock_irqrestore(&info->lock,flags);
4531                         }
4532                         goto cleanup;
4533                 }
4534         }
4535
4536         /* status
4537          *
4538          * 15      buffer complete
4539          * 14..06  reserved
4540          * 05..04  residue
4541          * 02      eof (end of frame)
4542          * 01      CRC error
4543          * 00      abort
4544          */
4545         status = desc_status(info->rbufs[end]);
4546
4547         /* ignore CRC bit if not using CRC (bit is undefined) */
4548         if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4549                 status &= ~BIT1;
4550
4551         if (framesize == 0 ||
4552                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4553                 free_rbufs(info, start, end);
4554                 goto check_again;
4555         }
4556
4557         if (framesize < (2 + crc_size) || status & BIT0) {
4558                 info->icount.rxshort++;
4559                 framesize = 0;
4560         } else if (status & BIT1) {
4561                 info->icount.rxcrc++;
4562                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4563                         framesize = 0;
4564         }
4565
4566 #if SYNCLINK_GENERIC_HDLC
4567         if (framesize == 0) {
4568                 info->netdev->stats.rx_errors++;
4569                 info->netdev->stats.rx_frame_errors++;
4570         }
4571 #endif
4572
4573         DBGBH(("%s rx frame status=%04X size=%d\n",
4574                 info->device_name, status, framesize));
4575         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4576
4577         if (framesize) {
4578                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4579                         framesize -= crc_size;
4580                         crc_size = 0;
4581                 }
4582
4583                 if (framesize > info->max_frame_size + crc_size)
4584                         info->icount.rxlong++;
4585                 else {
4586                         /* copy dma buffer(s) to contiguous temp buffer */
4587                         int copy_count = framesize;
4588                         int i = start;
4589                         unsigned char *p = info->tmp_rbuf;
4590                         info->tmp_rbuf_count = framesize;
4591
4592                         info->icount.rxok++;
4593
4594                         while(copy_count) {
4595                                 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4596                                 memcpy(p, info->rbufs[i].buf, partial_count);
4597                                 p += partial_count;
4598                                 copy_count -= partial_count;
4599                                 if (++i == info->rbuf_count)
4600                                         i = 0;
4601                         }
4602
4603                         if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4604                                 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4605                                 framesize++;
4606                         }
4607
4608 #if SYNCLINK_GENERIC_HDLC
4609                         if (info->netcount)
4610                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4611                         else
4612 #endif
4613                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4614                 }
4615         }
4616         free_rbufs(info, start, end);
4617         return true;
4618
4619 cleanup:
4620         return false;
4621 }
4622
4623 /*
4624  * pass receive buffer (RAW synchronous mode) to tty layer
4625  * return true if buffer available, otherwise false
4626  */
4627 static bool rx_get_buf(struct slgt_info *info)
4628 {
4629         unsigned int i = info->rbuf_current;
4630         unsigned int count;
4631
4632         if (!desc_complete(info->rbufs[i]))
4633                 return false;
4634         count = desc_count(info->rbufs[i]);
4635         switch(info->params.mode) {
4636         case MGSL_MODE_MONOSYNC:
4637         case MGSL_MODE_BISYNC:
4638                 /* ignore residue in byte synchronous modes */
4639                 if (desc_residue(info->rbufs[i]))
4640                         count--;
4641                 break;
4642         }
4643         DBGDATA(info, info->rbufs[i].buf, count, "rx");
4644         DBGINFO(("rx_get_buf size=%d\n", count));
4645         if (count)
4646                 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4647                                   info->flag_buf, count);
4648         free_rbufs(info, i, i);
4649         return true;
4650 }
4651
4652 static void reset_tbufs(struct slgt_info *info)
4653 {
4654         unsigned int i;
4655         info->tbuf_current = 0;
4656         for (i=0 ; i < info->tbuf_count ; i++) {
4657                 info->tbufs[i].status = 0;
4658                 info->tbufs[i].count  = 0;
4659         }
4660 }
4661
4662 /*
4663  * return number of free transmit DMA buffers
4664  */
4665 static unsigned int free_tbuf_count(struct slgt_info *info)
4666 {
4667         unsigned int count = 0;
4668         unsigned int i = info->tbuf_current;
4669
4670         do
4671         {
4672                 if (desc_count(info->tbufs[i]))
4673                         break; /* buffer in use */
4674                 ++count;
4675                 if (++i == info->tbuf_count)
4676                         i=0;
4677         } while (i != info->tbuf_current);
4678
4679         /* if tx DMA active, last zero count buffer is in use */
4680         if (count && (rd_reg32(info, TDCSR) & BIT0))
4681                 --count;
4682
4683         return count;
4684 }
4685
4686 /*
4687  * return number of bytes in unsent transmit DMA buffers
4688  * and the serial controller tx FIFO
4689  */
4690 static unsigned int tbuf_bytes(struct slgt_info *info)
4691 {
4692         unsigned int total_count = 0;
4693         unsigned int i = info->tbuf_current;
4694         unsigned int reg_value;
4695         unsigned int count;
4696         unsigned int active_buf_count = 0;
4697
4698         /*
4699          * Add descriptor counts for all tx DMA buffers.
4700          * If count is zero (cleared by DMA controller after read),
4701          * the buffer is complete or is actively being read from.
4702          *
4703          * Record buf_count of last buffer with zero count starting
4704          * from current ring position. buf_count is mirror
4705          * copy of count and is not cleared by serial controller.
4706          * If DMA controller is active, that buffer is actively
4707          * being read so add to total.
4708          */
4709         do {
4710                 count = desc_count(info->tbufs[i]);
4711                 if (count)
4712                         total_count += count;
4713                 else if (!total_count)
4714                         active_buf_count = info->tbufs[i].buf_count;
4715                 if (++i == info->tbuf_count)
4716                         i = 0;
4717         } while (i != info->tbuf_current);
4718
4719         /* read tx DMA status register */
4720         reg_value = rd_reg32(info, TDCSR);
4721
4722         /* if tx DMA active, last zero count buffer is in use */
4723         if (reg_value & BIT0)
4724                 total_count += active_buf_count;
4725
4726         /* add tx FIFO count = reg_value[15..8] */
4727         total_count += (reg_value >> 8) & 0xff;
4728
4729         /* if transmitter active add one byte for shift register */
4730         if (info->tx_active)
4731                 total_count++;
4732
4733         return total_count;
4734 }
4735
4736 /*
4737  * load transmit DMA buffer(s) with data
4738  */
4739 static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4740 {
4741         unsigned short count;
4742         unsigned int i;
4743         struct slgt_desc *d;
4744
4745         if (size == 0)
4746                 return;
4747
4748         DBGDATA(info, buf, size, "tx");
4749
4750         info->tbuf_start = i = info->tbuf_current;
4751
4752         while (size) {
4753                 d = &info->tbufs[i];
4754                 if (++i == info->tbuf_count)
4755                         i = 0;
4756
4757                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4758                 memcpy(d->buf, buf, count);
4759
4760                 size -= count;
4761                 buf  += count;
4762
4763                 /*
4764                  * set EOF bit for last buffer of HDLC frame or
4765                  * for every buffer in raw mode
4766                  */
4767                 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4768                     info->params.mode == MGSL_MODE_RAW)
4769                         set_desc_eof(*d, 1);
4770                 else
4771                         set_desc_eof(*d, 0);
4772
4773                 set_desc_count(*d, count);
4774                 d->buf_count = count;
4775         }
4776
4777         info->tbuf_current = i;
4778 }
4779
4780 static int register_test(struct slgt_info *info)
4781 {
4782         static unsigned short patterns[] =
4783                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4784         static unsigned int count = sizeof(patterns)/sizeof(patterns[0]);
4785         unsigned int i;
4786         int rc = 0;
4787
4788         for (i=0 ; i < count ; i++) {
4789                 wr_reg16(info, TIR, patterns[i]);
4790                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4791                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4792                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4793                         rc = -ENODEV;
4794                         break;
4795                 }
4796         }
4797         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4798         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4799         return rc;
4800 }
4801
4802 static int irq_test(struct slgt_info *info)
4803 {
4804         unsigned long timeout;
4805         unsigned long flags;
4806         struct tty_struct *oldtty = info->port.tty;
4807         u32 speed = info->params.data_rate;
4808
4809         info->params.data_rate = 921600;
4810         info->port.tty = NULL;
4811
4812         spin_lock_irqsave(&info->lock, flags);
4813         async_mode(info);
4814         slgt_irq_on(info, IRQ_TXIDLE);
4815
4816         /* enable transmitter */
4817         wr_reg16(info, TCR,
4818                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4819
4820         /* write one byte and wait for tx idle */
4821         wr_reg16(info, TDR, 0);
4822
4823         /* assume failure */
4824         info->init_error = DiagStatus_IrqFailure;
4825         info->irq_occurred = false;
4826
4827         spin_unlock_irqrestore(&info->lock, flags);
4828
4829         timeout=100;
4830         while(timeout-- && !info->irq_occurred)
4831                 msleep_interruptible(10);
4832
4833         spin_lock_irqsave(&info->lock,flags);
4834         reset_port(info);
4835         spin_unlock_irqrestore(&info->lock,flags);
4836
4837         info->params.data_rate = speed;
4838         info->port.tty = oldtty;
4839
4840         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4841         return info->irq_occurred ? 0 : -ENODEV;
4842 }
4843
4844 static int loopback_test_rx(struct slgt_info *info)
4845 {
4846         unsigned char *src, *dest;
4847         int count;
4848
4849         if (desc_complete(info->rbufs[0])) {
4850                 count = desc_count(info->rbufs[0]);
4851                 src   = info->rbufs[0].buf;
4852                 dest  = info->tmp_rbuf;
4853
4854                 for( ; count ; count-=2, src+=2) {
4855                         /* src=data byte (src+1)=status byte */
4856                         if (!(*(src+1) & (BIT9 + BIT8))) {
4857                                 *dest = *src;
4858                                 dest++;
4859                                 info->tmp_rbuf_count++;
4860                         }
4861                 }
4862                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4863                 return 1;
4864         }
4865         return 0;
4866 }
4867
4868 static int loopback_test(struct slgt_info *info)
4869 {
4870 #define TESTFRAMESIZE 20
4871
4872         unsigned long timeout;
4873         u16 count = TESTFRAMESIZE;
4874         unsigned char buf[TESTFRAMESIZE];
4875         int rc = -ENODEV;
4876         unsigned long flags;
4877
4878         struct tty_struct *oldtty = info->port.tty;
4879         MGSL_PARAMS params;
4880
4881         memcpy(&params, &info->params, sizeof(params));
4882
4883         info->params.mode = MGSL_MODE_ASYNC;
4884         info->params.data_rate = 921600;
4885         info->params.loopback = 1;
4886         info->port.tty = NULL;
4887
4888         /* build and send transmit frame */
4889         for (count = 0; count < TESTFRAMESIZE; ++count)
4890                 buf[count] = (unsigned char)count;
4891
4892         info->tmp_rbuf_count = 0;
4893         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4894
4895         /* program hardware for HDLC and enabled receiver */
4896         spin_lock_irqsave(&info->lock,flags);
4897         async_mode(info);
4898         rx_start(info);
4899         info->tx_count = count;
4900         tx_load(info, buf, count);
4901         tx_start(info);
4902         spin_unlock_irqrestore(&info->lock, flags);
4903
4904         /* wait for receive complete */
4905         for (timeout = 100; timeout; --timeout) {
4906                 msleep_interruptible(10);
4907                 if (loopback_test_rx(info)) {
4908                         rc = 0;
4909                         break;
4910                 }
4911         }
4912
4913         /* verify received frame length and contents */
4914         if (!rc && (info->tmp_rbuf_count != count ||
4915                   memcmp(buf, info->tmp_rbuf, count))) {
4916                 rc = -ENODEV;
4917         }
4918
4919         spin_lock_irqsave(&info->lock,flags);
4920         reset_adapter(info);
4921         spin_unlock_irqrestore(&info->lock,flags);
4922
4923         memcpy(&info->params, &params, sizeof(info->params));
4924         info->port.tty = oldtty;
4925
4926         info->init_error = rc ? DiagStatus_DmaFailure : 0;
4927         return rc;
4928 }
4929
4930 static int adapter_test(struct slgt_info *info)
4931 {
4932         DBGINFO(("testing %s\n", info->device_name));
4933         if (register_test(info) < 0) {
4934                 printk("register test failure %s addr=%08X\n",
4935                         info->device_name, info->phys_reg_addr);
4936         } else if (irq_test(info) < 0) {
4937                 printk("IRQ test failure %s IRQ=%d\n",
4938                         info->device_name, info->irq_level);
4939         } else if (loopback_test(info) < 0) {
4940                 printk("loopback test failure %s\n", info->device_name);
4941         }
4942         return info->init_error;
4943 }
4944
4945 /*
4946  * transmit timeout handler
4947  */
4948 static void tx_timeout(unsigned long context)
4949 {
4950         struct slgt_info *info = (struct slgt_info*)context;
4951         unsigned long flags;
4952
4953         DBGINFO(("%s tx_timeout\n", info->device_name));
4954         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
4955                 info->icount.txtimeout++;
4956         }
4957         spin_lock_irqsave(&info->lock,flags);
4958         info->tx_active = false;
4959         info->tx_count = 0;
4960         spin_unlock_irqrestore(&info->lock,flags);
4961
4962 #if SYNCLINK_GENERIC_HDLC
4963         if (info->netcount)
4964                 hdlcdev_tx_done(info);
4965         else
4966 #endif
4967                 bh_transmit(info);
4968 }
4969
4970 /*
4971  * receive buffer polling timer
4972  */
4973 static void rx_timeout(unsigned long context)
4974 {
4975         struct slgt_info *info = (struct slgt_info*)context;
4976         unsigned long flags;
4977
4978         DBGINFO(("%s rx_timeout\n", info->device_name));
4979         spin_lock_irqsave(&info->lock, flags);
4980         info->pending_bh |= BH_RECEIVE;
4981         spin_unlock_irqrestore(&info->lock, flags);
4982         bh_handler(&info->task);
4983 }
4984