2 # Character device configuration
5 menu "Character devices"
8 bool "Virtual terminal" if EMBEDDED
13 If you say Y here, you will get support for terminal devices with
14 display and keyboard devices. These are called "virtual" because you
15 can run several virtual terminals (also called virtual consoles) on
16 one physical terminal. This is rather useful, for example one
17 virtual terminal can collect system messages and warnings, another
18 one can be used for a text-mode user session, and a third could run
19 an X session, all in parallel. Switching between virtual terminals
20 is done with certain key combinations, usually Alt-<function key>.
22 The setterm command ("man setterm") can be used to change the
23 properties (such as colors or beeping) of a virtual terminal. The
24 man page console_codes(4) ("man console_codes") contains the special
25 character sequences that can be used to change those properties
26 directly. The fonts used on virtual terminals can be changed with
27 the setfont ("man setfont") command and the key bindings are defined
28 with the loadkeys ("man loadkeys") command.
30 You need at least one virtual terminal device in order to make use
31 of your keyboard and monitor. Therefore, only people configuring an
32 embedded system would want to say N here in order to save some
33 memory; the only way to log into such a system is then via a serial
34 or network connection.
36 If unsure, say Y, or else you won't be able to do much with your new
37 shiny Linux system :-)
39 config CONSOLE_TRANSLATIONS
42 bool "Enable character translations in console" if EMBEDDED
44 This enables support for font mapping and Unicode translation
48 bool "Support for console on virtual terminal" if EMBEDDED
52 The system console is the device which receives all kernel messages
53 and warnings and which allows logins in single user mode. If you
54 answer Y here, a virtual terminal (the device used to interact with
55 a physical terminal) can be used as system console. This is the most
56 common mode of operations, so you should say Y here unless you want
57 the kernel messages be output only to a serial port (in which case
58 you should say Y to "Console on serial port", below).
60 If you do say Y here, by default the currently visible virtual
61 terminal (/dev/tty0) will be used as system console. You can change
62 that with a kernel command line option such as "console=tty3" which
63 would use the third virtual terminal as system console. (Try "man
64 bootparam" or see the documentation of your boot loader (lilo or
65 loadlin) about how to pass options to the kernel at boot time.)
71 depends on VT && !S390 && !UML
74 config VT_HW_CONSOLE_BINDING
75 bool "Support for binding and unbinding console drivers"
79 The virtual terminal is the device that interacts with the physical
80 terminal through console drivers. On these systems, at least one
81 console driver is loaded. In other configurations, additional console
82 drivers may be enabled, such as the framebuffer console. If more than
83 1 console driver is enabled, setting this to 'y' will allow you to
84 select the console driver that will serve as the backend for the
87 See <file:Documentation/console/console.txt> for more
88 information. For framebuffer console users, please refer to
89 <file:Documentation/fb/fbcon.txt>.
92 bool "/dev/kmem virtual device support"
95 Say Y here if you want to support the /dev/kmem device. The
96 /dev/kmem device is rarely used, but can be used for certain
97 kind of kernel debugging operations.
98 When in doubt, say "N".
100 config SERIAL_NONSTANDARD
101 bool "Non-standard serial port support"
104 Say Y here if you have any non-standard serial boards -- boards
105 which aren't supported using the standard "dumb" serial driver.
106 This includes intelligent serial boards such as Cyclades,
107 Digiboards, etc. These are usually used for systems that need many
108 serial ports because they serve many terminals or dial-in
111 Note that the answer to this question won't directly affect the
112 kernel: saying N will just cause the configurator to skip all
113 the questions about non-standard serial boards.
115 Most people can say N here.
118 tristate "Computone IntelliPort Plus serial support"
119 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
121 This driver supports the entire family of Intelliport II/Plus
122 controllers with the exception of the MicroChannel controllers and
123 products previous to the Intelliport II. These are multiport cards,
124 which give you many serial ports. You would need something like this
125 to connect more than two modems to your Linux box, for instance in
126 order to become a dial-in server. If you have a card like that, say
127 Y here and read <file:Documentation/computone.txt>.
129 To compile this driver as modules, choose M here: the
130 modules will be called ip2 and ip2main.
133 tristate "Comtrol RocketPort support"
134 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
136 This driver supports Comtrol RocketPort and RocketModem PCI boards.
137 These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or
138 modems. For information about the RocketPort/RocketModem boards
139 and this driver read <file:Documentation/rocket.txt>.
141 To compile this driver as a module, choose M here: the
142 module will be called rocket.
144 If you want to compile this driver into the kernel, say Y here. If
145 you don't have a Comtrol RocketPort/RocketModem card installed, say N.
148 tristate "Cyclades async mux support"
149 depends on SERIAL_NONSTANDARD && (PCI || ISA)
152 This driver supports Cyclades Z and Y multiserial boards.
153 You would need something like this to connect more than two modems to
154 your Linux box, for instance in order to become a dial-in server.
156 For information about the Cyclades-Z card, read
157 <file:Documentation/README.cycladesZ>.
159 To compile this driver as a module, choose M here: the
160 module will be called cyclades.
162 If you haven't heard about it, it's safe to say N.
165 bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)"
166 depends on EXPERIMENTAL && CYCLADES
168 The Cyclades-Z family of multiport cards allows 2 (two) driver op
169 modes: polling and interrupt. In polling mode, the driver will check
170 the status of the Cyclades-Z ports every certain amount of time
171 (which is called polling cycle and is configurable). In interrupt
172 mode, it will use an interrupt line (IRQ) in order to check the
173 status of the Cyclades-Z ports. The default op mode is polling. If
177 tristate "Digiboard Intelligent Async Support"
178 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
180 This is a driver for Digi International's Xx, Xeve, and Xem series
181 of cards which provide multiple serial ports. You would need
182 something like this to connect more than two modems to your Linux
183 box, for instance in order to become a dial-in server. This driver
184 supports the original PC (ISA) boards as well as PCI, and EISA. If
185 you have a card like this, say Y here and read the file
186 <file:Documentation/digiepca.txt>.
188 To compile this driver as a module, choose M here: the
189 module will be called epca.
192 tristate "Hayes ESP serial port support"
193 depends on SERIAL_NONSTANDARD && ISA && ISA_DMA_API
195 This is a driver which supports Hayes ESP serial ports. Both single
196 port cards and multiport cards are supported. Make sure to read
197 <file:Documentation/hayes-esp.txt>.
199 To compile this driver as a module, choose M here: the
200 module will be called esp.
205 tristate "Moxa Intellio support"
206 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
209 Say Y here if you have a Moxa Intellio multiport serial card.
211 To compile this driver as a module, choose M here: the
212 module will be called moxa.
215 tristate "Moxa SmartIO support v. 2.0"
216 depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA)
218 Say Y here if you have a Moxa SmartIO multiport serial card and/or
219 want to help develop a new version of this driver.
221 This is upgraded (1.9.1) driver from original Moxa drivers with
222 changes finally resulting in PCI probing.
224 This driver can also be built as a module. The module will be called
225 mxser. If you want to do that, say M here.
228 tristate "Multi-Tech multiport card support (EXPERIMENTAL)"
229 depends on SERIAL_NONSTANDARD && PCI
232 This is a driver for the Multi-Tech cards which provide several
233 serial ports. The driver is experimental and can currently only be
234 built as a module. The module will be called isicom.
235 If you want to do that, choose M here.
238 tristate "Microgate SyncLink card support"
239 depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API
241 Provides support for the SyncLink ISA and PCI multiprotocol serial
242 adapters. These adapters support asynchronous and HDLC bit
243 synchronous communication up to 10Mbps (PCI adapter).
245 This driver can only be built as a module ( = code which can be
246 inserted in and removed from the running kernel whenever you want).
247 The module will be called synclink. If you want to do that, say M
251 tristate "SyncLink Multiport support"
252 depends on SERIAL_NONSTANDARD && PCI
254 Enable support for the SyncLink Multiport (2 or 4 ports)
255 serial adapter, running asynchronous and HDLC communications up
256 to 2.048Mbps. Each ports is independently selectable for
257 RS-232, V.35, RS-449, RS-530, and X.21
259 This driver may be built as a module ( = code which can be
260 inserted in and removed from the running kernel whenever you want).
261 The module will be called synclinkmp. If you want to do that, say M
265 tristate "SyncLink GT/AC support"
266 depends on SERIAL_NONSTANDARD && PCI
268 Support for SyncLink GT and SyncLink AC families of
269 synchronous and asynchronous serial adapters
270 manufactured by Microgate Systems, Ltd. (www.microgate.com)
273 tristate "HDLC line discipline support"
274 depends on SERIAL_NONSTANDARD
276 Allows synchronous HDLC communications with tty device drivers that
277 support synchronous HDLC such as the Microgate SyncLink adapter.
279 This driver can only be built as a module ( = code which can be
280 inserted in and removed from the running kernel whenever you want).
281 The module will be called n_hdlc. If you want to do that, say M
285 tristate "SDL RISCom/8 card support"
286 depends on SERIAL_NONSTANDARD
288 This is a driver for the SDL Communications RISCom/8 multiport card,
289 which gives you many serial ports. You would need something like
290 this to connect more than two modems to your Linux box, for instance
291 in order to become a dial-in server. If you have a card like that,
292 say Y here and read the file <file:Documentation/riscom8.txt>.
294 Also it's possible to say M here and compile this driver as kernel
295 loadable module; the module will be called riscom8.
298 tristate "Specialix IO8+ card support"
299 depends on SERIAL_NONSTANDARD
301 This is a driver for the Specialix IO8+ multiport card (both the
302 ISA and the PCI version) which gives you many serial ports. You
303 would need something like this to connect more than two modems to
304 your Linux box, for instance in order to become a dial-in server.
306 If you have a card like that, say Y here and read the file
307 <file:Documentation/specialix.txt>. Also it's possible to say M here
308 and compile this driver as kernel loadable module which will be
311 config SPECIALIX_RTSCTS
312 bool "Specialix DTR/RTS pin is RTS"
315 The Specialix IO8+ card can only support either RTS or DTR. If you
316 say N here, the driver will use the pin as "DTR" when the tty is in
317 software handshake mode. If you say Y here or hardware handshake is
318 on, it will always be RTS. Read the file
319 <file:Documentation/specialix.txt> for more information.
322 tristate "Specialix SX (and SI) card support"
323 depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA)
325 This is a driver for the SX and SI multiport serial cards.
326 Please read the file <file:Documentation/sx.txt> for details.
328 This driver can only be built as a module ( = code which can be
329 inserted in and removed from the running kernel whenever you want).
330 The module will be called sx. If you want to do that, say M here.
333 tristate "Specialix RIO system support"
334 depends on SERIAL_NONSTANDARD
336 This is a driver for the Specialix RIO, a smart serial card which
337 drives an outboard box that can support up to 128 ports. Product
338 information is at <http://www.perle.com/support/documentation.html#multiport>.
339 There are both ISA and PCI versions.
342 bool "Support really old RIO/PCI cards"
345 Older RIO PCI cards need some initialization-time configuration to
346 determine the IRQ and some control addresses. If you have a RIO and
347 this doesn't seem to work, try setting this to Y.
350 bool "Stallion multiport serial support"
351 depends on SERIAL_NONSTANDARD
353 Stallion cards give you many serial ports. You would need something
354 like this to connect more than two modems to your Linux box, for
355 instance in order to become a dial-in server. If you say Y here,
356 you will be asked for your specific card model in the next
357 questions. Make sure to read <file:Documentation/stallion.txt> in
358 this case. If you have never heard about all this, it's safe to
362 tristate "Stallion EasyIO or EC8/32 support"
363 depends on STALDRV && BROKEN_ON_SMP && (ISA || EISA || PCI)
365 If you have an EasyIO or EasyConnection 8/32 multiport Stallion
366 card, then this is for you; say Y. Make sure to read
367 <file:Documentation/stallion.txt>.
369 To compile this driver as a module, choose M here: the
370 module will be called stallion.
373 tristate "Stallion EC8/64, ONboard, Brumby support"
374 depends on STALDRV && BROKEN_ON_SMP && (ISA || EISA || PCI)
376 If you have an EasyConnection 8/64, ONboard, Brumby or Stallion
377 serial multiport card, say Y here. Make sure to read
378 <file:Documentation/stallion.txt>.
380 To compile this driver as a module, choose M here: the
381 module will be called istallion.
384 tristate "HSDPA Broadband Wireless Data Card - Globe Trotter"
385 depends on PCI && EXPERIMENTAL
387 If you have a HSDPA driver Broadband Wireless Data Card -
388 Globe Trotter PCMCIA card, say Y here.
390 To compile this driver as a module, choose M here, the module
391 will be called nozomi.
394 tristate "Commodore A2232 serial support (EXPERIMENTAL)"
395 depends on EXPERIMENTAL && ZORRO && BROKEN_ON_SMP
397 This option supports the 2232 7-port serial card shipped with the
398 Amiga 2000 and other Zorro-bus machines, dating from 1989. At
399 a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip
400 each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The
401 ports were connected with 8 pin DIN connectors on the card bracket,
402 for which 8 pin to DB25 adapters were supplied. The card also had
403 jumpers internally to toggle various pinning configurations.
405 This driver can be built as a module; but then "generic_serial"
406 will also be built as a module. This has to be loaded before
407 "ser_a2232". If you want to do this, answer M here.
410 bool "SGI Altix system controller communication support"
411 depends on (IA64_SGI_SN2 || IA64_GENERIC)
413 If you have an SGI Altix and you want to enable system
414 controller communication from user space (you want this!),
415 say Y. Otherwise, say N.
418 bool "SGI TIO CX driver support"
419 depends on (IA64_SGI_SN2 || IA64_GENERIC)
421 If you have an SGI Altix and you have fpga devices attached
422 to your TIO, say Y here, otherwise say N.
425 tristate "SGI FPGA Core Services driver support"
428 If you have an SGI Altix with an attached SABrick
429 say Y or M here, otherwise say N.
431 source "drivers/serial/Kconfig"
434 bool "Unix98 PTY support" if EMBEDDED
437 A pseudo terminal (PTY) is a software device consisting of two
438 halves: a master and a slave. The slave device behaves identical to
439 a physical terminal; the master device is used by a process to
440 read data from and write data to the slave, thereby emulating a
441 terminal. Typical programs for the master side are telnet servers
444 Linux has traditionally used the BSD-like names /dev/ptyxx for
445 masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
446 has a number of problems. The GNU C library glibc 2.1 and later,
447 however, supports the Unix98 naming standard: in order to acquire a
448 pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
449 terminal is then made available to the process and the pseudo
450 terminal slave can be accessed as /dev/pts/<number>. What was
451 traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
453 All modern Linux systems use the Unix98 ptys. Say Y unless
454 you're on an embedded system and want to conserve memory.
457 bool "Legacy (BSD) PTY support"
460 A pseudo terminal (PTY) is a software device consisting of two
461 halves: a master and a slave. The slave device behaves identical to
462 a physical terminal; the master device is used by a process to
463 read data from and write data to the slave, thereby emulating a
464 terminal. Typical programs for the master side are telnet servers
467 Linux has traditionally used the BSD-like names /dev/ptyxx
468 for masters and /dev/ttyxx for slaves of pseudo
469 terminals. This scheme has a number of problems, including
470 security. This option enables these legacy devices; on most
471 systems, it is safe to say N.
474 config LEGACY_PTY_COUNT
475 int "Maximum number of legacy PTY in use"
476 depends on LEGACY_PTYS
480 The maximum number of legacy PTYs that can be used at any one time.
481 The default is 256, and should be more than enough. Embedded
482 systems may want to reduce this to save memory.
484 When not in use, each legacy PTY occupies 12 bytes on 32-bit
485 architectures and 24 bytes on 64-bit architectures.
488 tristate 'Total Impact briQ front panel driver'
491 The briQ is a small footprint CHRP computer with a frontpanel VFD, a
492 tristate led and two switches. It is the size of a CDROM drive.
494 If you have such one and want anything showing on the VFD then you
497 To compile this driver as a module, choose M here: the
498 module will be called briq_panel.
500 It's safe to say N here.
503 tristate "Blackfin On-Chip OTP Memory Support"
504 depends on BLACKFIN && (BF52x || BF54x)
507 If you say Y here, you will get support for a character device
508 interface into the One Time Programmable memory pages that are
509 stored on the Blackfin processor. This will not get you access
510 to the secure memory pages however. You will need to write your
511 own secure code and reader for that.
513 To compile this driver as a module, choose M here: the module
514 will be called bfin-otp.
516 If unsure, it is safe to say Y.
518 config BFIN_OTP_WRITE_ENABLE
519 bool "Enable writing support of OTP pages"
523 If you say Y here, you will enable support for writing of the
524 OTP pages. This is dangerous by nature as you can only program
525 the pages once, so only enable this option when you actually
526 need it so as to not inadvertently clobber data.
531 tristate "Parallel printer support"
534 If you intend to attach a printer to the parallel port of your Linux
535 box (as opposed to using a serial printer; if the connector at the
536 printer has 9 or 25 holes ["female"], then it's serial), say Y.
537 Also read the Printing-HOWTO, available from
538 <http://www.tldp.org/docs.html#howto>.
540 It is possible to share one parallel port among several devices
541 (e.g. printer and ZIP drive) and it is safe to compile the
542 corresponding drivers into the kernel.
544 To compile this driver as a module, choose M here and read
545 <file:Documentation/parport.txt>. The module will be called lp.
547 If you have several parallel ports, you can specify which ports to
548 use with the "lp" kernel command line option. (Try "man bootparam"
549 or see the documentation of your boot loader (lilo or loadlin) about
550 how to pass options to the kernel at boot time.) The syntax of the
551 "lp" command line option can be found in <file:drivers/char/lp.c>.
553 If you have more than 8 printers, you need to increase the LP_NO
554 macro in lp.c and the PARPORT_MAX macro in parport.h.
557 bool "Support for console on line printer"
560 If you want kernel messages to be printed out as they occur, you
561 can have a console on the printer. This option adds support for
562 doing that; to actually get it to happen you need to pass the
563 option "console=lp0" to the kernel at boot time.
565 If the printer is out of paper (or off, or unplugged, or too
566 busy..) the kernel will stall until the printer is ready again.
567 By defining CONSOLE_LP_STRICT to 0 (at your own risk) you
568 can make the kernel continue when this happens,
569 but it'll lose the kernel messages.
574 tristate "Support for user-space parallel port device drivers"
577 Saying Y to this adds support for /dev/parport device nodes. This
578 is needed for programs that want portable access to the parallel
579 port, for instance deviceid (which displays Plug-and-Play device
582 This is the parallel port equivalent of SCSI generic support (sg).
583 It is safe to say N to this -- it is not needed for normal printing
584 or parallel port CD-ROM/disk support.
586 To compile this driver as a module, choose M here: the
587 module will be called ppdev.
594 Generic "hypervisor virtual console" infrastructure for various
595 hypervisors (pSeries, iSeries, Xen, lguest).
596 It will automatically be selected if one of the back-end console drivers
601 bool "pSeries Hypervisor Virtual Console support"
602 depends on PPC_PSERIES
605 pSeries machines when partitioned support a hypervisor virtual
606 console. This driver allows each pSeries partition to have a console
607 which is accessed via the HMC.
610 bool "iSeries Hypervisor Virtual Console support"
611 depends on PPC_ISERIES
615 iSeries machines support a hypervisor virtual console.
618 bool "IBM RTAS Console support"
622 IBM Console device driver which makes use of RTAS
625 bool "Toshiba's Beat Hypervisor Console support"
626 depends on PPC_CELLEB
629 Toshiba's Cell Reference Set Beat Console device driver
632 bool "Xen Hypervisor Console support"
637 Xen virtual console device driver
639 config VIRTIO_CONSOLE
644 tristate "IBM Hypervisor Virtual Console Server support"
645 depends on PPC_PSERIES
647 Partitionable IBM Power5 ppc64 machines allow hosting of
648 firmware virtual consoles from one Linux partition by
649 another Linux partition. This driver allows console data
650 from Linux partitions to be accessed through TTY device
651 interfaces in the device tree of a Linux partition running
654 To compile this driver as a module, choose M here: the
655 module will be called hvcs.ko. Additionally, this module
656 will depend on arch specific APIs exported from hvcserver.ko
657 which will also be compiled when this driver is built as a
660 source "drivers/char/ipmi/Kconfig"
663 tristate "NetWinder thermometer support"
664 depends on ARCH_NETWINDER
666 Say Y here to include support for the thermal management hardware
667 found in the NetWinder. This driver allows the user to control the
668 temperature set points and to read the current temperature.
670 It is also possible to say M here to build it as a module (ds1620)
671 It is recommended to be used on a NetWinder, but it is not a
675 tristate "NetWinder Button"
676 depends on ARCH_NETWINDER
678 If you say Y here and create a character device node /dev/nwbutton
679 with major and minor numbers 10 and 158 ("man mknod"), then every
680 time the orange button is pressed a number of times, the number of
681 times the button was pressed will be written to that device.
683 This is most useful for applications, as yet unwritten, which
684 perform actions based on how many times the button is pressed in a
687 Do not hold the button down for too long, as the driver does not
688 alter the behaviour of the hardware reset circuitry attached to the
689 button; it will still execute a hard reset if the button is held
690 down for longer than approximately five seconds.
692 To compile this driver as a module, choose M here: the
693 module will be called nwbutton.
695 Most people will answer Y to this question and "Reboot Using Button"
696 below to be able to initiate a system shutdown from the button.
698 config NWBUTTON_REBOOT
699 bool "Reboot Using Button"
702 If you say Y here, then you will be able to initiate a system
703 shutdown and reboot by pressing the orange button a number of times.
704 The number of presses to initiate the shutdown is two by default,
705 but this can be altered by modifying the value of NUM_PRESSES_REBOOT
706 in nwbutton.h and recompiling the driver or, if you compile the
707 driver as a module, you can specify the number of presses at load
708 time with "insmod button reboot_count=<something>".
711 tristate "NetWinder flash support"
712 depends on ARCH_NETWINDER
714 If you say Y here and create a character device /dev/flash with
715 major 10 and minor 160 you can manipulate the flash ROM containing
716 the NetWinder firmware. Be careful as accidentally overwriting the
717 flash contents can render your computer unbootable. On no account
718 allow random users access to this device. :-)
720 To compile this driver as a module, choose M here: the
721 module will be called nwflash.
723 If you're not sure, say N.
725 source "drivers/char/hw_random/Kconfig"
728 tristate "/dev/nvram support"
729 depends on ATARI || X86 || ARM || GENERIC_NVRAM
731 If you say Y here and create a character special file /dev/nvram
732 with major number 10 and minor number 144 using mknod ("man mknod"),
733 you get read and write access to the extra bytes of non-volatile
734 memory in the real time clock (RTC), which is contained in every PC
735 and most Ataris. The actual number of bytes varies, depending on the
736 nvram in the system, but is usually 114 (128-14 for the RTC).
738 This memory is conventionally called "CMOS RAM" on PCs and "NVRAM"
739 on Ataris. /dev/nvram may be used to view settings there, or to
740 change them (with some utility). It could also be used to frequently
741 save a few bits of very important data that may not be lost over
742 power-off and for which writing to disk is too insecure. Note
743 however that most NVRAM space in a PC belongs to the BIOS and you
744 should NEVER idly tamper with it. See Ralf Brown's interrupt list
745 for a guide to the use of CMOS bytes by your BIOS.
747 On Atari machines, /dev/nvram is always configured and does not need
750 To compile this driver as a module, choose M here: the
751 module will be called nvram.
754 # These legacy RTC drivers just cause too many conflicts with the generic
755 # RTC framework ... let's not even try to coexist any more.
760 tristate "Enhanced Real Time Clock Support"
761 depends on !PPC && !PARISC && !IA64 && !M68K && !SPARC && !FRV \
762 && !ARM && !SUPERH && !S390 && !AVR32
764 If you say Y here and create a character special file /dev/rtc with
765 major number 10 and minor number 135 using mknod ("man mknod"), you
766 will get access to the real time clock (or hardware clock) built
769 Every PC has such a clock built in. It can be used to generate
770 signals from as low as 1Hz up to 8192Hz, and can also be used
771 as a 24 hour alarm. It reports status information via the file
772 /proc/driver/rtc and its behaviour is set by various ioctls on
775 If you run Linux on a multiprocessor machine and said Y to
776 "Symmetric Multi Processing" above, you should say Y here to read
777 and set the RTC in an SMP compatible fashion.
779 If you think you have a use for such a device (such as periodic data
780 sampling), then say Y here, and read <file:Documentation/rtc.txt>
783 To compile this driver as a module, choose M here: the
784 module will be called rtc.
787 tristate "Enhanced Real Time Clock Support"
788 depends on SPARC32 && PCI
790 If you say Y here and create a character special file /dev/rtc with
791 major number 10 and minor number 135 using mknod ("man mknod"), you
792 will get access to the real time clock (or hardware clock) built
795 Every PC has such a clock built in. It can be used to generate
796 signals from as low as 1Hz up to 8192Hz, and can also be used
797 as a 24 hour alarm. It reports status information via the file
798 /proc/driver/rtc and its behaviour is set by various ioctls on
801 If you think you have a use for such a device (such as periodic data
802 sampling), then say Y here, and read <file:Documentation/rtc.txt>
805 To compile this driver as a module, choose M here: the
806 module will be called js-rtc.
809 tristate "SGI DS1286 RTC support"
810 depends on SGI_HAS_DS1286
812 If you say Y here and create a character special file /dev/rtc with
813 major number 10 and minor number 135 using mknod ("man mknod"), you
814 will get access to the real time clock built into your computer.
815 Every SGI has such a clock built in. It reports status information
816 via the file /proc/rtc and its behaviour is set by various ioctls on
820 bool "SGI M48T35 RTC support"
823 If you say Y here and create a character special file /dev/rtc with
824 major number 10 and minor number 135 using mknod ("man mknod"), you
825 will get access to the real time clock built into your computer.
826 Every SGI has such a clock built in. It reports status information
827 via the file /proc/rtc and its behaviour is set by various ioctls on
831 tristate "Generic /dev/rtc emulation"
832 depends on RTC!=y && !IA64 && !ARM && !M32R && !MIPS && !SPARC && !FRV && !S390 && !SUPERH && !AVR32
834 If you say Y here and create a character special file /dev/rtc with
835 major number 10 and minor number 135 using mknod ("man mknod"), you
836 will get access to the real time clock (or hardware clock) built
839 It reports status information via the file /proc/driver/rtc and its
840 behaviour is set by various ioctls on /dev/rtc. If you enable the
841 "extended RTC operation" below it will also provide an emulation
842 for RTC_UIE which is required by some programs and may improve
843 precision in some cases.
845 To compile this driver as a module, choose M here: the
846 module will be called genrtc.
849 bool "Extended RTC operation"
852 Provides an emulation for RTC_UIE which is required by some programs
853 and may improve precision of the generic RTC support in some cases.
856 bool "EFI Real Time Clock Services"
860 tristate "DS1302 RTC support"
861 depends on M32R && (PLAT_M32700UT || PLAT_OPSPUT)
863 If you say Y here and create a character special file /dev/rtc with
864 major number 121 and minor number 0 using mknod ("man mknod"), you
865 will get access to the real time clock (or hardware clock) built
871 bool "Support for Cobalt LCD"
872 depends on MIPS_COBALT
874 This option enables support for the LCD display and buttons found
875 on Cobalt systems through a misc device.
878 tristate "Double Talk PC internal speech card support"
881 This driver is for the DoubleTalk PC, a speech synthesizer
882 manufactured by RC Systems (<http://www.rcsys.com/>). It is also
883 called the `internal DoubleTalk'.
885 To compile this driver as a module, choose M here: the
886 module will be called dtlk.
889 tristate "Xilinx HWICAP Support"
890 depends on XILINX_VIRTEX
892 This option enables support for Xilinx Internal Configuration
893 Access Port (ICAP) driver. The ICAP is used on Xilinx Virtex
894 FPGA platforms to partially reconfigure the FPGA at runtime.
899 tristate "Siemens R3964 line discipline"
901 This driver allows synchronous communication with devices using the
902 Siemens R3964 packet protocol. Unless you are dealing with special
903 hardware like PLCs, you are unlikely to need this.
905 To compile this driver as a module, choose M here: the
906 module will be called n_r3964.
911 tristate "Applicom intelligent fieldbus card support"
914 This driver provides the kernel-side support for the intelligent
915 fieldbus cards made by Applicom International. More information
916 about these cards can be found on the WWW at the address
917 <http://www.applicom-int.com/>, or by email from David Woodhouse
918 <dwmw2@infradead.org>.
920 To compile this driver as a module, choose M here: the
921 module will be called applicom.
926 tristate "Sony Vaio Programmable I/O Control Device support (EXPERIMENTAL)"
927 depends on EXPERIMENTAL && X86 && PCI && INPUT && !64BIT
929 This driver enables access to the Sony Programmable I/O Control
930 Device which can be found in many (all ?) Sony Vaio laptops.
932 If you have one of those laptops, read
933 <file:Documentation/laptops/sonypi.txt>, and say Y or M here.
935 To compile this driver as a module, choose M here: the
936 module will be called sonypi.
939 tristate "TANBAC TB0219 GPIO support"
940 depends on TANBAC_TB022X
943 source "drivers/char/pcmcia/Kconfig"
946 tristate "ACP Modem (Mwave) support"
950 The ACP modem (Mwave) for Linux is a WinModem. It is composed of a
951 kernel driver and a user level application. Together these components
952 support direct attachment to public switched telephone networks (PSTNs)
953 and support selected world wide countries.
955 This version of the ACP Modem driver supports the IBM Thinkpad 600E,
956 600, and 770 that include on board ACP modem hardware.
958 The modem also supports the standard communications port interface
959 (ttySx) and is compatible with the Hayes AT Command Set.
961 The user level application needed to use this driver can be found at
962 the IBM Linux Technology Center (LTC) web site:
963 <http://www.ibm.com/linux/ltc/>.
965 If you own one of the above IBM Thinkpads which has the Mwave chipset
968 To compile this driver as a module, choose M here: the
969 module will be called mwave.
972 tristate "NatSemi SCx200 GPIO Support"
976 Give userspace access to the GPIO pins on the National
977 Semiconductor SCx200 processors.
979 If compiled as a module, it will be called scx200_gpio.
982 tristate "NatSemi PC8736x GPIO Support"
984 default SCx200_GPIO # mostly N
985 select NSC_GPIO # needed for support routines
987 Give userspace access to the GPIO pins on the National
988 Semiconductor PC-8736x (x=[03456]) SuperIO chip. The chip
989 has multiple functional units, inc several managed by
990 hwmon/pc87360 driver. Tested with PC-87366
992 If compiled as a module, it will be called pc8736x_gpio.
995 tristate "NatSemi Base GPIO Support"
997 # selected by SCx200_GPIO and PC8736x_GPIO
998 # what about 2 selectors differing: m != y
1000 Common support used (and needed) by scx200_gpio and
1001 pc8736x_gpio drivers. If those drivers are built as
1002 modules, this one will be too, named nsc_gpio
1005 tristate "AMD CS5535/CS5536 GPIO (Geode Companion Device)"
1008 Give userspace access to the GPIO pins on the AMD CS5535 and
1009 CS5536 Geode companion devices.
1011 If compiled as a module, it will be called cs5535_gpio.
1014 tristate "NEC VR4100 series General-purpose I/O Unit support"
1015 depends on CPU_VR41XX
1018 tristate "RAW driver (/dev/raw/rawN)"
1021 The raw driver permits block devices to be bound to /dev/raw/rawN.
1022 Once bound, I/O against /dev/raw/rawN uses efficient zero-copy I/O.
1023 See the raw(8) manpage for more details.
1025 Applications should preferably open the device (eg /dev/hda1)
1026 with the O_DIRECT flag.
1029 int "Maximum number of RAW devices to support (1-8192)"
1030 depends on RAW_DRIVER
1033 The maximum number of RAW devices that are supported.
1034 Default is 256. Increase this number in case you need lots of
1038 bool "HPET - High Precision Event Timer" if (X86 || IA64)
1042 If you say Y here, you will have a miscdevice named "/dev/hpet/". Each
1043 open selects one of the timers supported by the HPET. The timers are
1044 non-periodic and/or periodic.
1047 bool "HPET Control RTC IRQ" if !HPET_EMULATE_RTC
1051 If you say Y here, you will disable RTC_IRQ in drivers/char/rtc.c. It
1052 is assumed the platform called hpet_alloc with the RTC IRQ values for
1056 bool "Allow mmap of HPET"
1060 If you say Y here, user applications will be able to mmap
1063 In some hardware implementations, the page containing HPET
1064 registers may also contain other things that shouldn't be
1065 exposed to the user. If this applies to your hardware,
1068 config HANGCHECK_TIMER
1069 tristate "Hangcheck timer"
1070 depends on X86 || IA64 || PPC64 || S390
1072 The hangcheck-timer module detects when the system has gone
1073 out to lunch past a certain margin. It can reboot the system
1074 or merely print a warning.
1077 tristate "MMTIMER Memory mapped RTC for SGI Altix"
1078 depends on IA64_GENERIC || IA64_SGI_SN2
1081 The mmtimer device allows direct userspace access to the
1084 source "drivers/char/tpm/Kconfig"
1087 tristate "Telecom clock driver for ATCA SBC"
1088 depends on EXPERIMENTAL && X86
1091 The telecom clock device is specific to the MPCBL0010 and MPCBL0050
1092 ATCA computers and allows direct userspace access to the
1093 configuration of the telecom clock configuration settings. This
1094 device is used for hardware synchronization across the ATCA backplane
1095 fabric. Upon loading, the driver exports a sysfs directory,
1096 /sys/devices/platform/telco_clock, with a number of files for
1097 controlling the behavior of this hardware.
1102 depends on ISA || PCI
1105 source "drivers/s390/char/Kconfig"
projects / linux-2.6-omap-h63xx.git / blob