2 * linux/arch/arm/mach-omap2/board-omap3beagle.c
4 * Copyright (C) 2008 Texas Instruments
6 * Modified from mach-omap2/board-3430sdp.c
8 * Initial code: Syed Mohammed Khasim
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/platform_device.h>
18 #include <linux/delay.h>
19 #include <linux/err.h>
20 #include <linux/clk.h>
22 #include <linux/leds.h>
23 #include <linux/gpio.h>
24 #include <linux/input.h>
25 #include <linux/gpio_keys.h>
27 #include <linux/mtd/mtd.h>
28 #include <linux/mtd/partitions.h>
29 #include <linux/mtd/nand.h>
31 #include <linux/regulator/machine.h>
32 #include <linux/i2c/twl4030.h>
34 #include <mach/hardware.h>
35 #include <asm/mach-types.h>
36 #include <asm/mach/arch.h>
37 #include <asm/mach/map.h>
38 #include <asm/mach/flash.h>
40 #include <mach/board.h>
42 #include <mach/common.h>
43 #include <mach/gpmc.h>
44 #include <mach/nand.h>
47 #include "twl4030-generic-scripts.h"
48 #include "mmc-twl4030.h"
51 #define GPMC_CS0_BASE 0x60
52 #define GPMC_CS_SIZE 0x30
54 #define NAND_BLOCK_SIZE SZ_128K
56 static struct mtd_partition omap3beagle_nand_partitions[] = {
57 /* All the partition sizes are listed in terms of NAND block size */
61 .size = 4 * NAND_BLOCK_SIZE,
62 .mask_flags = MTD_WRITEABLE, /* force read-only */
66 .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
67 .size = 15 * NAND_BLOCK_SIZE,
68 .mask_flags = MTD_WRITEABLE, /* force read-only */
72 .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
73 .size = 1 * NAND_BLOCK_SIZE,
77 .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
78 .size = 32 * NAND_BLOCK_SIZE,
81 .name = "File System",
82 .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
83 .size = MTDPART_SIZ_FULL,
87 static struct omap_nand_platform_data omap3beagle_nand_data = {
88 .options = NAND_BUSWIDTH_16,
89 .parts = omap3beagle_nand_partitions,
90 .nr_parts = ARRAY_SIZE(omap3beagle_nand_partitions),
91 .dma_channel = -1, /* disable DMA in OMAP NAND driver */
96 static struct resource omap3beagle_nand_resource = {
97 .flags = IORESOURCE_MEM,
100 static struct platform_device omap3beagle_nand_device = {
101 .name = "omap2-nand",
104 .platform_data = &omap3beagle_nand_data,
107 .resource = &omap3beagle_nand_resource,
110 #include "sdram-micron-mt46h32m32lf-6.h"
112 static struct omap_uart_config omap3_beagle_uart_config __initdata = {
113 .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
116 static struct twl4030_usb_data beagle_usb_data = {
117 .usb_mode = T2_USB_MODE_ULPI,
120 static struct twl4030_hsmmc_info mmc[] = {
129 static struct regulator_consumer_supply beagle_vmmc1_supply = {
133 static struct regulator_consumer_supply beagle_vsim_supply = {
134 .supply = "vmmc_aux",
137 static struct gpio_led gpio_leds[];
139 static int beagle_twl_gpio_setup(struct device *dev,
140 unsigned gpio, unsigned ngpio)
142 /* gpio + 0 is "mmc0_cd" (input/IRQ) */
143 omap_cfg_reg(AH8_34XX_GPIO29);
144 mmc[0].gpio_cd = gpio + 0;
145 twl4030_mmc_init(mmc);
147 /* link regulators to MMC adapters */
148 beagle_vmmc1_supply.dev = mmc[0].dev;
149 beagle_vsim_supply.dev = mmc[0].dev;
151 /* REVISIT: need ehci-omap hooks for external VBUS
152 * power switch and overcurrent detect
155 gpio_request(gpio + 1, "EHCI_nOC");
156 gpio_direction_input(gpio + 1);
158 /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
159 gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
160 gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
162 /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
163 gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
168 static struct twl4030_gpio_platform_data beagle_gpio_data = {
169 .gpio_base = OMAP_MAX_GPIO_LINES,
170 .irq_base = TWL4030_GPIO_IRQ_BASE,
171 .irq_end = TWL4030_GPIO_IRQ_END,
174 .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
175 | BIT(15) | BIT(16) | BIT(17),
176 .setup = beagle_twl_gpio_setup,
179 static struct platform_device omap3_beagle_lcd_device = {
180 .name = "omap3beagle_lcd",
184 static struct regulator_consumer_supply beagle_vdac_supply = {
186 .dev = &omap3_beagle_lcd_device.dev,
189 static struct regulator_consumer_supply beagle_vdvi_supply = {
191 .dev = &omap3_beagle_lcd_device.dev,
194 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
195 static struct regulator_init_data beagle_vmmc1 = {
199 .valid_modes_mask = REGULATOR_MODE_NORMAL
200 | REGULATOR_MODE_STANDBY,
201 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
202 | REGULATOR_CHANGE_MODE
203 | REGULATOR_CHANGE_STATUS,
205 .num_consumer_supplies = 1,
206 .consumer_supplies = &beagle_vmmc1_supply,
209 /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
210 static struct regulator_init_data beagle_vsim = {
214 .valid_modes_mask = REGULATOR_MODE_NORMAL
215 | REGULATOR_MODE_STANDBY,
216 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
217 | REGULATOR_CHANGE_MODE
218 | REGULATOR_CHANGE_STATUS,
220 .num_consumer_supplies = 1,
221 .consumer_supplies = &beagle_vsim_supply,
224 /* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
225 static struct regulator_init_data beagle_vdac = {
229 .valid_modes_mask = REGULATOR_MODE_NORMAL
230 | REGULATOR_MODE_STANDBY,
231 .valid_ops_mask = REGULATOR_CHANGE_MODE
232 | REGULATOR_CHANGE_STATUS,
234 .num_consumer_supplies = 1,
235 .consumer_supplies = &beagle_vdac_supply,
238 /* VPLL2 for digital video outputs */
239 static struct regulator_init_data beagle_vpll2 = {
244 .valid_modes_mask = REGULATOR_MODE_NORMAL
245 | REGULATOR_MODE_STANDBY,
246 .valid_ops_mask = REGULATOR_CHANGE_MODE
247 | REGULATOR_CHANGE_STATUS,
249 .num_consumer_supplies = 1,
250 .consumer_supplies = &beagle_vdvi_supply,
253 static const struct twl4030_resconfig beagle_resconfig[] = {
254 /* disable regulators that u-boot left enabled; the
255 * devices' drivers should be managing these.
257 { .resource = RES_VAUX3, }, /* not even connected! */
258 { .resource = RES_VMMC1, },
259 { .resource = RES_VSIM, },
260 { .resource = RES_VPLL2, },
261 { .resource = RES_VDAC, },
262 { .resource = RES_VUSB_1V5, },
263 { .resource = RES_VUSB_1V8, },
264 { .resource = RES_VUSB_3V1, },
268 static struct twl4030_power_data beagle_power_data = {
269 .resource_config = beagle_resconfig,
270 /* REVISIT can't use GENERIC3430_T2SCRIPTS_DATA;
271 * among other things, it makes reboot fail.
275 static struct twl4030_platform_data beagle_twldata = {
276 .irq_base = TWL4030_IRQ_BASE,
277 .irq_end = TWL4030_IRQ_END,
279 /* platform_data for children goes here */
280 .usb = &beagle_usb_data,
281 .gpio = &beagle_gpio_data,
282 .power = &beagle_power_data,
283 .vmmc1 = &beagle_vmmc1,
284 .vsim = &beagle_vsim,
285 .vdac = &beagle_vdac,
286 .vpll2 = &beagle_vpll2,
289 static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
291 I2C_BOARD_INFO("twl4030", 0x48),
292 .flags = I2C_CLIENT_WAKE,
293 .irq = INT_34XX_SYS_NIRQ,
294 .platform_data = &beagle_twldata,
298 static int __init omap3_beagle_i2c_init(void)
300 omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
301 ARRAY_SIZE(beagle_i2c_boardinfo));
302 /* Bus 3 is attached to the DVI port where devices like the pico DLP
303 * projector don't work reliably with 400kHz */
304 omap_register_i2c_bus(3, 100, NULL, 0);
308 static void __init omap3_beagle_init_irq(void)
310 omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
315 static struct omap_lcd_config omap3_beagle_lcd_config __initdata = {
316 .ctrl_name = "internal",
319 static struct gpio_led gpio_leds[] = {
321 .name = "beagleboard::usr0",
322 .default_trigger = "heartbeat",
326 .name = "beagleboard::usr1",
327 .default_trigger = "mmc0",
331 .name = "beagleboard::pmu_stat",
332 .gpio = -EINVAL, /* gets replaced */
337 static struct gpio_led_platform_data gpio_led_info = {
339 .num_leds = ARRAY_SIZE(gpio_leds),
342 static struct platform_device leds_gpio = {
346 .platform_data = &gpio_led_info,
350 static struct gpio_keys_button gpio_buttons[] = {
359 static struct gpio_keys_platform_data gpio_key_info = {
360 .buttons = gpio_buttons,
361 .nbuttons = ARRAY_SIZE(gpio_buttons),
364 static struct platform_device keys_gpio = {
368 .platform_data = &gpio_key_info,
372 static struct omap_board_config_kernel omap3_beagle_config[] __initdata = {
373 { OMAP_TAG_UART, &omap3_beagle_uart_config },
374 { OMAP_TAG_LCD, &omap3_beagle_lcd_config },
377 static struct platform_device *omap3_beagle_devices[] __initdata = {
378 &omap3_beagle_lcd_device,
383 static void __init omap3beagle_flash_init(void)
386 u8 nandcs = GPMC_CS_NUM + 1;
388 u32 gpmc_base_add = OMAP34XX_GPMC_VIRT;
390 /* find out the chip-select on which NAND exists */
391 while (cs < GPMC_CS_NUM) {
393 ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
395 if ((ret & 0xC00) == 0x800) {
396 printk(KERN_INFO "Found NAND on CS%d\n", cs);
397 if (nandcs > GPMC_CS_NUM)
403 if (nandcs > GPMC_CS_NUM) {
404 printk(KERN_INFO "NAND: Unable to find configuration "
409 if (nandcs < GPMC_CS_NUM) {
410 omap3beagle_nand_data.cs = nandcs;
411 omap3beagle_nand_data.gpmc_cs_baseaddr = (void *)
412 (gpmc_base_add + GPMC_CS0_BASE + nandcs * GPMC_CS_SIZE);
413 omap3beagle_nand_data.gpmc_baseaddr = (void *) (gpmc_base_add);
415 printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
416 if (platform_device_register(&omap3beagle_nand_device) < 0)
417 printk(KERN_ERR "Unable to register NAND device\n");
421 static void __init omap3_beagle_init(void)
423 omap3_beagle_i2c_init();
424 platform_add_devices(omap3_beagle_devices,
425 ARRAY_SIZE(omap3_beagle_devices));
426 omap_board_config = omap3_beagle_config;
427 omap_board_config_size = ARRAY_SIZE(omap3_beagle_config);
430 omap_cfg_reg(J25_34XX_GPIO170);
431 gpio_request(170, "DVI_nPD");
432 /* REVISIT leave DVI powered down until it's needed ... */
433 gpio_direction_output(170, true);
437 omap3beagle_flash_init();
440 static void __init omap3_beagle_map_io(void)
442 omap2_set_globals_343x();
443 omap2_map_common_io();
446 MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
447 /* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
448 .phys_io = 0x48000000,
449 .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
450 .boot_params = 0x80000100,
451 .map_io = omap3_beagle_map_io,
452 .init_irq = omap3_beagle_init_irq,
453 .init_machine = omap3_beagle_init,
454 .timer = &omap_timer,