arch/arm/mach-omap2/board-3430sdp.c

   1 /*
   2  * linux/arch/arm/mach-omap2/board-3430sdp.c
   3  *
   4  * Copyright (C) 2007 Texas Instruments
   5  *
   6  * Modified from mach-omap2/board-generic.c
   7  *
   8  * Initial code: Syed Mohammed Khasim
   9  *
  10  * This program is free software; you can redistribute it and/or modify
  11  * it under the terms of the GNU General Public License version 2 as
  12  * published by the Free Software Foundation.
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/init.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/delay.h>
  19 #include <linux/input.h>
  20 #include <linux/workqueue.h>
  21 #include <linux/err.h>
  22 #include <linux/clk.h>
  23 #include <linux/spi/spi.h>
  24 #include <linux/spi/ads7846.h>
  25 #include <linux/i2c/twl4030.h>
  26
  27 #include <mach/hardware.h>
  28 #include <asm/mach-types.h>
  29 #include <asm/mach/arch.h>
  30 #include <asm/mach/map.h>
  31
  32 #include <mach/mcspi.h>
  33 #include <mach/gpio.h>
  34 #include <mach/mux.h>
  35 #include <mach/board.h>
  36 #include <mach/usb-musb.h>
  37 #include <mach/usb-ehci.h>
  38 #include <mach/hsmmc.h>
  39 #include <mach/common.h>
  40 #include <mach/keypad.h>
  41 #include <mach/dma.h>
  42 #include <mach/gpmc.h>
  43 #include <linux/i2c/twl4030-rtc.h>
  44
  45 #include <asm/io.h>
  46 #include <asm/delay.h>
  47 #include <mach/control.h>
  48
  49 #include "sdram-qimonda-hyb18m512160af-6.h"
  50
  51 #define SDP3430_SMC91X_CS       3
  52
  53 #define ENABLE_VAUX3_DEDICATED  0x03
  54 #define ENABLE_VAUX3_DEV_GRP    0x20
  55
  56
  57 #define TWL4030_MSECURE_GPIO 22
  58
  59 static struct resource sdp3430_smc91x_resources[] = {
  60         [0] = {
  61                 .start  = OMAP34XX_ETHR_START,
  62                 .end    = OMAP34XX_ETHR_START + SZ_4K,
  63                 .flags  = IORESOURCE_MEM,
  64         },
  65         [1] = {
  66                 .start  = 0,
  67                 .end    = 0,
  68                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
  69         },
  70 };
  71
  72 static struct platform_device sdp3430_smc91x_device = {
  73         .name           = "smc91x",
  74         .id             = -1,
  75         .num_resources  = ARRAY_SIZE(sdp3430_smc91x_resources),
  76         .resource       = sdp3430_smc91x_resources,
  77 };
  78
  79 static int sdp3430_keymap[] = {
  80         KEY(0, 0, KEY_LEFT),
  81         KEY(0, 1, KEY_RIGHT),
  82         KEY(0, 2, KEY_A),
  83         KEY(0, 3, KEY_B),
  84         KEY(0, 4, KEY_C),
  85         KEY(1, 0, KEY_DOWN),
  86         KEY(1, 1, KEY_UP),
  87         KEY(1, 2, KEY_E),
  88         KEY(1, 3, KEY_F),
  89         KEY(1, 4, KEY_G),
  90         KEY(2, 0, KEY_ENTER),
  91         KEY(2, 1, KEY_I),
  92         KEY(2, 2, KEY_J),
  93         KEY(2, 3, KEY_K),
  94         KEY(2, 4, KEY_3),
  95         KEY(3, 0, KEY_M),
  96         KEY(3, 1, KEY_N),
  97         KEY(3, 2, KEY_O),
  98         KEY(3, 3, KEY_P),
  99         KEY(3, 4, KEY_Q),
 100         KEY(4, 0, KEY_R),
 101         KEY(4, 1, KEY_4),
 102         KEY(4, 2, KEY_T),
 103         KEY(4, 3, KEY_U),
 104         KEY(4, 4, KEY_D),
 105         KEY(5, 0, KEY_V),
 106         KEY(5, 1, KEY_W),
 107         KEY(5, 2, KEY_L),
 108         KEY(5, 3, KEY_S),
 109         KEY(5, 4, KEY_H),
 110         0
 111 };
 112
 113 static struct omap_kp_platform_data sdp3430_kp_data = {
 114         .rows           = 5,
 115         .cols           = 6,
 116         .keymap         = sdp3430_keymap,
 117         .keymapsize     = ARRAY_SIZE(sdp3430_keymap),
 118         .rep            = 1,
 119         .irq            = TWL4030_MODIRQ_KEYPAD,
 120 };
 121
 122 static struct platform_device sdp3430_kp_device = {
 123         .name           = "omap_twl4030keypad",
 124         .id             = -1,
 125         .dev            = {
 126                 .platform_data  = &sdp3430_kp_data,
 127         },
 128 };
 129
 130 static int ts_gpio;
 131
 132 static int __init msecure_init(void)
 133 {
 134         int ret = 0;
 135
 136 #ifdef CONFIG_RTC_DRV_TWL4030
 137         /* 3430ES2.0 doesn't have msecure/gpio-22 line connected to T2 */
 138         if (omap_type() == OMAP2_DEVICE_TYPE_GP &&
 139                         system_rev < OMAP3430_REV_ES2_0) {
 140                 u32 msecure_pad_config_reg = omap_ctrl_base_get() + 0xA3C;
 141                 int mux_mask = 0x04;
 142                 u16 tmp;
 143
 144                 ret = gpio_request(TWL4030_MSECURE_GPIO, "msecure");
 145                 if (ret < 0) {
 146                         printk(KERN_ERR "msecure_init: can't"
 147                                 "reserve GPIO:%d !\n", TWL4030_MSECURE_GPIO);
 148                         goto out;
 149                 }
 150                 /*
 151                  * TWL4030 will be in secure mode if msecure line from OMAP
 152                  * is low. Make msecure line high in order to change the
 153                  * TWL4030 RTC time and calender registers.
 154                  */
 155                 tmp = omap_readw(msecure_pad_config_reg);
 156                 tmp &= 0xF8; /* To enable mux mode 03/04 = GPIO_RTC */
 157                 tmp |= mux_mask;/* To enable mux mode 03/04 = GPIO_RTC */
 158                 omap_writew(tmp, msecure_pad_config_reg);
 159
 160                 gpio_direction_output(TWL4030_MSECURE_GPIO, 1);
 161         }
 162 out:
 163 #endif
 164         return ret;
 165 }
 166
 167 /**
 168  * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
 169  *
 170  * @return - void. If request gpio fails then Flag KERN_ERR.
 171  */
 172 static void ads7846_dev_init(void)
 173 {
 174         if (omap_request_gpio(ts_gpio) < 0) {
 175                 printk(KERN_ERR "can't get ads746 pen down GPIO\n");
 176                 return;
 177         }
 178
 179         omap_set_gpio_direction(ts_gpio, 1);
 180
 181         omap_set_gpio_debounce(ts_gpio, 1);
 182         omap_set_gpio_debounce_time(ts_gpio, 0xa);
 183 }
 184
 185 static int ads7846_get_pendown_state(void)
 186 {
 187         return !omap_get_gpio_datain(ts_gpio);
 188 }
 189
 190 /*
 191  * This enable(1)/disable(0) the voltage for TS: uses twl4030 calls
 192  */
 193 static int ads7846_vaux_control(int vaux_cntrl)
 194 {
 195         int ret = 0;
 196
 197 #ifdef CONFIG_TWL4030_CORE
 198         /* check for return value of ldo_use: if success it returns 0 */
 199         if (vaux_cntrl == VAUX_ENABLE) {
 200                 if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
 201                         ENABLE_VAUX3_DEDICATED, TWL4030_VAUX3_DEDICATED))
 202                         return -EIO;
 203                 if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
 204                         ENABLE_VAUX3_DEV_GRP, TWL4030_VAUX3_DEV_GRP))
 205                         return -EIO;
 206         } else if (vaux_cntrl == VAUX_DISABLE) {
 207                 if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
 208                         0x00, TWL4030_VAUX3_DEDICATED))
 209                         return -EIO;
 210                 if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
 211                         0x00, TWL4030_VAUX3_DEV_GRP))
 212                         return -EIO;
 213         }
 214 #else
 215         ret = -EIO;
 216 #endif
 217         return ret;
 218 }
 219
 220 static struct ads7846_platform_data tsc2046_config __initdata = {
 221         .get_pendown_state      = ads7846_get_pendown_state,
 222         .keep_vref_on           = 1,
 223         .vaux_control           = ads7846_vaux_control,
 224 };
 225
 226
 227 static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
 228         .turbo_mode     = 0,
 229         .single_channel = 1,  /* 0: slave, 1: master */
 230 };
 231
 232 static struct spi_board_info sdp3430_spi_board_info[] __initdata = {
 233         [0] = {
 234                 /*
 235                  * TSC2046 operates at a max freqency of 2MHz, so
 236                  * operate slightly below at 1.5MHz
 237                  */
 238                 .modalias               = "ads7846",
 239                 .bus_num                = 1,
 240                 .chip_select            = 0,
 241                 .max_speed_hz           = 1500000,
 242                 .controller_data        = &tsc2046_mcspi_config,
 243                 .irq                    = 0,
 244                 .platform_data          = &tsc2046_config,
 245         },
 246 };
 247
 248 static struct platform_device sdp3430_lcd_device = {
 249         .name           = "sdp2430_lcd",
 250         .id             = -1,
 251 };
 252
 253 static struct platform_device *sdp3430_devices[] __initdata = {
 254         &sdp3430_smc91x_device,
 255         &sdp3430_kp_device,
 256         &sdp3430_lcd_device,
 257 };
 258
 259 static inline void __init sdp3430_init_smc91x(void)
 260 {
 261         int eth_cs;
 262         unsigned long cs_mem_base;
 263         int eth_gpio = 0;
 264
 265         eth_cs = SDP3430_SMC91X_CS;
 266
 267         if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
 268                 printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
 269                 return;
 270         }
 271
 272         sdp3430_smc91x_resources[0].start = cs_mem_base + 0x0;
 273         sdp3430_smc91x_resources[0].end   = cs_mem_base + 0xf;
 274         udelay(100);
 275
 276         if (system_rev > OMAP3430_REV_ES1_0)
 277                 eth_gpio = OMAP34XX_ETHR_GPIO_IRQ_SDPV2;
 278         else
 279                 eth_gpio = OMAP34XX_ETHR_GPIO_IRQ_SDPV1;
 280
 281         sdp3430_smc91x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
 282
 283         if (omap_request_gpio(eth_gpio) < 0) {
 284                 printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
 285                         eth_gpio);
 286                 return;
 287         }
 288         omap_set_gpio_direction(eth_gpio, 1);
 289 }
 290
 291 static void __init omap_3430sdp_init_irq(void)
 292 {
 293         omap2_init_common_hw(hyb18m512160af6_sdrc_params);
 294         omap_init_irq();
 295         omap_gpio_init();
 296         sdp3430_init_smc91x();
 297 }
 298
 299 static struct omap_uart_config sdp3430_uart_config __initdata = {
 300         .enabled_uarts  = ((1 << 0) | (1 << 1) | (1 << 2)),
 301 };
 302
 303 static struct omap_lcd_config sdp3430_lcd_config __initdata = {
 304         .ctrl_name      = "internal",
 305 };
 306
 307 static struct omap_board_config_kernel sdp3430_config[] __initdata = {
 308         { OMAP_TAG_UART,        &sdp3430_uart_config },
 309         { OMAP_TAG_LCD,         &sdp3430_lcd_config },
 310 };
 311
 312 static struct twl4030_platform_data sdp3430_twldata = {
 313         .irq_base       = TWL4030_IRQ_BASE,
 314         .irq_end        = TWL4030_IRQ_END,
 315 };
 316
 317 static struct i2c_board_info __initdata sdp3430_i2c_boardinfo[] = {
 318         {
 319                 I2C_BOARD_INFO("twl4030", 0x48),
 320                 .flags = I2C_CLIENT_WAKE,
 321                 .irq = INT_34XX_SYS_NIRQ,
 322                 .platform_data = &sdp3430_twldata,
 323         },
 324 };
 325
 326 static int __init omap3430_i2c_init(void)
 327 {
 328         omap_register_i2c_bus(1, 2600, sdp3430_i2c_boardinfo,
 329                         ARRAY_SIZE(sdp3430_i2c_boardinfo));
 330         omap_register_i2c_bus(2, 400, NULL, 0);
 331         omap_register_i2c_bus(3, 400, NULL, 0);
 332         return 0;
 333 }
 334
 335 extern void __init sdp3430_flash_init(void);
 336
 337 static void __init omap_3430sdp_init(void)
 338 {
 339         omap3430_i2c_init();
 340         platform_add_devices(sdp3430_devices, ARRAY_SIZE(sdp3430_devices));
 341         omap_board_config = sdp3430_config;
 342         omap_board_config_size = ARRAY_SIZE(sdp3430_config);
 343         if (system_rev > OMAP3430_REV_ES1_0)
 344                 ts_gpio = OMAP34XX_TS_GPIO_IRQ_SDPV2;
 345         else
 346                 ts_gpio = OMAP34XX_TS_GPIO_IRQ_SDPV1;
 347         sdp3430_spi_board_info[0].irq = OMAP_GPIO_IRQ(ts_gpio);
 348         spi_register_board_info(sdp3430_spi_board_info,
 349                                 ARRAY_SIZE(sdp3430_spi_board_info));
 350         ads7846_dev_init();
 351         sdp3430_flash_init();
 352         msecure_init();
 353         twl4030_bci_battery_init();
 354         omap_serial_init();
 355         usb_musb_init();
 356         usb_ehci_init();
 357         hsmmc_init();
 358 }
 359
 360 static void __init omap_3430sdp_map_io(void)
 361 {
 362         omap2_set_globals_343x();
 363         omap2_map_common_io();
 364 }
 365
 366 MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
 367         /* Maintainer: Syed Khasim - Texas Instruments Inc */
 368         .phys_io        = 0x48000000,
 369         .io_pg_offst    = ((0xd8000000) >> 18) & 0xfffc,
 370         .boot_params    = 0x80000100,
 371         .map_io         = omap_3430sdp_map_io,
 372         .init_irq       = omap_3430sdp_init_irq,
 373         .init_machine   = omap_3430sdp_init,
 374         .timer          = &omap_timer,
 375 MACHINE_END